B AT T E R Y C H AR G E R BATTERY CHARGER NG3 CANBUS Installation and User Manual ...................................
Battery charger NG3 CANBUS Mechanical dimension 220 368 100 95 7 430 N.B. All dimensions are expressed in mm. Drilling details 220 40 140 40 15 401 430 UP Advised Installation 60 2 100 60 14 N.B. All dimensions are expressed in mm.
Battery Charger NG3 CANBUS Mechanical dimension with Air Pump 220 445 210 540 N.B. All dimensions are expressed in mm. Drilling details with Air Pump Ø6.5 505 540 UP Advised Installation Ø6.5 N.B. All dimensions are expressed in mm.
English Battery charger NG3 CANBUS ATTENTION: To reduce the risk of electric shock, do not remove cover. Refer servicing to qualified service personnel. Disconnect the mains supply before connecting or disconnecting the links to the battery. Read the Instruction Manual carefully before use. Verify that the selected charge curve is suitable for the type of battery You have to re-charge.
Battery charger NG3 CANBUS English LED Indicator RED LED shows that battery is in the initial charging phase. YELLOW LED shows that battery charger has reached 80% of charge. GREEN LED shows that battery has reached 100% of charge. 100% 80% 80% Further information can be found in the description of the Charging Curve. START Example: RED LED on with short flashing indicates a constant tension phase.
English Battery charger NG3 CANBUS Charging curve selection (if display is present) You can press the MODE button according to two modalities: 1. Long pressure (at least 1 second): during battery charger setting, it means ENTER 2. Short pressure (less than 1 second): during battery charger setting, it means ROLL. Setting: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Turn on the equipment while pressing the MODE button.
Battery charger NG3 CANBUS Micro-fit contacts 6 5 4 3 2 1 English CANBUS connector pinout Pin N° Description Pin N° Description 1 Pump pressure sensor 1 CAN low 2 Generic digital input 2 CAN low 3 GND 3 CAN negative 4 Hardware S/S 4 +12V (internal) 5 GND 5 CAN high with termination (120Ω) 6 Not used 6 GND (internal) 7 PPT100 7 CAN high 8 NPT100 8 CAN high 9 Green LED 9 CAN positive 12 11 10 9 8 7 10 GND 11 Red LED 12 Not used Auxiliary Contacts AUX1 NC C
English Battery charger NG3 CANBUS TECHNICAL FEATURES Ta=25°C unless otherwise specified Mains side Description Supply Voltage Frequency Absorbed Maximum Current Inrush Current Power Factor Absorbed Minimum Power Absorbed Maximum Power Symbol Vin f Iinmax cosϕ Pinmin Pinmax Test Condition P = Pmax Vin = 230Veff P = Pmax End of charge P = Pmax Value and/or Range 230 ± 10% 50 ÷ 60 22 < 1,35 0,68 <5 3 Unit Veff Hz Aeff A W kW Battery side Description Output current Maximum output current Output current r
Battery charger NG3 CANBUS English ADDITIONAL FEATURES WITH AIR PUMP Standard Version The Air Pump technology generates a re-mix of the acid inside the battery by a delivery of air pumping. The battery charger controls the air pump by an auxiliary contact (generally AUX1). An air injection cycle along all the charging period is held as per requirements of the battery specifications.
Italiano Carica batteria NG3 CANBUS Progettazione, produzione e vendita: ZIVAN SRL Via Bertona, 63/1 42028 Poviglio (RE) ITALIA Tel. +39 0522 960593 Fax +39 0522 967417 info@zivan.it www.zivan.it UFFICI VENDITA AUSTRALIA M+H Power Systems 9 Mosrael Place Rowville, Victoria, 3178 TEL: +61 3 9763 0555 FAX: +61 3 9763 0577 sales@mhpower.com.au www.mhpower.com.au BELGIUM BATTERY SUPPLIES NV Lindestraat, 89A 8790 Waregem Tel +32 56 617977 Fax +32 56 617955 battery.supplies@skynet.be www.batterysupplies.
Carica batteria NG3 CANBUS D01737-01 Italiano 11
ZIVAN S.r.l. Via Bertona, 63/1 42028 Poviglio (RE) ITALIA Tel. +39 0522 960593 Fax +39 0522 967417 E-mail: info@zivan.it Web: www.zivan.
