User Manual HBL100/HBL200 Version: 1.
Contents Read Before Use..................................................................................................................................1 Safety Cautions............................................................................................................................ 1 Position and Gesture....................................................................................................................2 Facial Expression...........................................................
Low Battery Warning....................................................................................................................8 Emergency Charging................................................................................................................... 8 Emergency Mechanical Key.........................................................................................................9 How to Use..................................................................................................
Read Before Use Safety Cautions 1. The factory setting of all new locks cannot unlock with any verification. 2. Please register at least one administrator for the newly installed lock. The lock cannot register any normal users without an administrator. 3. The lock is equipped with mechanical keys for manual unlocking. Please keep the mechanical keys at a safe place. 4. Please replace or charge the battery soon when the lock prompts the low battery warning. 5.
Position and Gesture If the user’s height is 1.60-1.80m, the height from handle centerline to ground is 1m. Facial Expression During enrollment and verification, keep the facial expression natural. Do not use exaggerated expressions (such as staring and grinning).
Face Position During enrollment and verification, adjust your face into the white frame on the screen. Follow the device instructions. Method for Using the Touch Screen Click the touch screen with your finger pulp and keep your fingers and screen clean during use.
Method for Fingerprint Registration Recommended fingers: The thumb, index finger or middle finger; avoid using the ring finger and little finger. Press your finger on the sensor area, with the fingerprint’s center aligning to the center of the sensor area. Vertical Sides Slant Too Low Note: Please use the correct method to place your finger onto the surface of the sensor for registration and verification.
Structure Front Back 2.
Basic Function User Introduction Group Admin Normal User Verification Mode Function Face Fingerprint Passcode Card Access to menu Open the door Open the door Notes: 1) Fingerprint recognition is only available for the HBL100 series products. 2) The maximum face/fingerprint/passcode/card capacity is 100 for all groups. Initialization Initializing the lock means all data will be deleted and restored to factory default setting.
Lockout Mode Lockout mode means that only administrator can unlock the door from outside. The lockout button is above the handle of indoor unit. Enable: Press and hold the lockout button for 3 seconds until the red-light blinks twice. Disable: Press and hold the lockout button for 3 seconds until the green-light blinks twice. It can also be disabled when an administrator unlocks the door from outside or by turning the handle downward from inside.
Network Control Supports Bluetooth or ZigBee communication. Note: ZK SmartKey app is used with Bluetooth communication. Amazon Alexa app is used with ZigBee communication. Operate Alarm After 4 failed verification attempts, the system will automatically take a photo of the user and save it. Low Battery Warning When the battery power is low, the device will generate alarm sound. The screen will display the prompt "Low battery". In this case, you cannot access Main Menu.
Emergency Mechanical Key The mechanical key is used to open the door when the lock has electronic malfunction. Note: Keep the mechanical key at a safe place.
How to Use Enter Main Menu When no administrator is registered in the device, the process is as follows: ① Touch the fingerprint sensor or wake up key to wake up the screen, the system will enter face mode automatically. ② Then click the menu key 10 HBL100/HBL200 User Manual to enter main menu.
When an administrator is registered in the device, the process is as follows: ① Touch the fingerprint sensor or wake up key to wake up the screen, the system will enter face mode automatically. ② Click the menu key to enter verify admin mode, then verify the admin by face/fingerprint/ password/card. ③ After the verification is successful, the system will enter main menu automatically. Note: If you want to verify the admin by passcode, please click the keyboard key to enter passcode mode.
Register User [Main Menu > New User] Note: 1) The User ID can contain 1 to 999. The number cannot be modified after the user is registered. 2) Once any detail is successfully registered, the system automatically goes to the New User page. You can continue to register for other methods. 3) When you click the return key to exit the New User page, the system automatically saves the user registration information.
Register Face [Main Menu > New User > Face] ① Focus face inside the white box, adjust the positions of the face by adjusting within the box. Check the status in the progress bar at the bottom of the page. ② After the face is successfully registered, the system automatically goes to the New User page. Note: If you try to register the same face again, the system displays the prompt "This face is already used.
Register Fingerprints [Main Menu > New User > Fingerprint] ① Place a finger on the fingerprint sensor. ② When the prompt "Place your finger second time" is displayed on the screen, move your finger away and place the finger; so on. ③ After the finger is successfully registered for three times, the system automatically goes to the New User page. Note: Each user can register 10 fingerprints. If you try to register the same finger again, the system displays the prompt "Fingerprint is already used.
Register Passcode [Main Menu > New User > Passcode] ① Enter six digits passcode and then click [OK]. ② Enter the passcode again for confirmation, and then click [OK] to complete the passcode registration. Then the system automatically goes to the New User page. Note: 1) The passcode length must be 6 digits; otherwise, the system displays the prompt "Passcode must be six digits".
Register Card [Main Menu > New User > Card] Place a card at the card detection area. After you hear a beep, the system displays hexadecimal card number, and automatically goes to the New User page. Note: If the card has been registered is already in use, the system displays the prompt "This card is already enrolled".
Manage Users [Main Menu > User Mgt.] Modify User Information ① Click on desired user to access the Edit User page. ② Click the [User Role] column to modify the role types. Click the [Face/Fingerprint/Passcode/ Card] column to register again. For the registration processes, view the above section Register User. ③ Click the return key to exit the Edit User page, the system automatically saves the user registration information. Delete User Information ① Click on desired user to access the Edit User page.
Language Setting [Main Menu > System > Operate Setting > Language] Click the [Language] column to set the desired language, and reboot the device to make the setting effective. Verification Mode [Main Menu > System > Operate Setting > Verify Mode] Click the [Verify Mode] column to choose desired verification mode. Verification Mode All Users All users only need one verification method to unlock. Admin Only Only the administrators can unlock the door. Safety Mode Combined recognitions.
Operate Alarm [Main Menu > System > Operate Setting > Operate Alarm] Click the [Operate Alarm] column to enable or disable the alarm function, which is off by default. Note: After 4 failed unauthorized verification attempt, one user photo will be taken. On subsequent screen wake, the photo will be displayed as an alarm. Normal Open Mode [Main Menu > System > Operate Setting > Normal Open] Click the [Normal Open] column to enable or disable the normal open mode, which is off by default.
Click the [Date Format] column to set the date format, it includes YY-MM-DD, YY/MM/DD, YY.MM.DD, YYYY-MM-DD, MM-DD and MM/DD. Advanced Options [Main Menu > System > Advanced Options] Click the [Face] column to enable or disable the face recognition function, which is enabled by default. If it is disabled, the face recognition page will no longer be displayed when waking up the screen or entering the main menu.
Upgrade Firmware [Main Menu > U-Disk >Upgrade Firmware] Click the [Upgrade Firmware] column to start the upgrade through the USB disk, and the update process can be seen on the screen. Before the upgrade, check whether the corresponding upgrade file is available on the USB disk. Users are not recommended to upgrade the firmware. If you really need to upgrade the firmware, please do it under the guidance of the manufacturer.
records. The system can save up to 10 photos. After the query is completed, the system displays the prompt "Data query completed". System Information [Main Menu > System Info] Click the [Capacity] column to check device capacity information. Click the [Device Info] column to check the device information.
ZK Building, Wuhe Road, Gangtou, Bantian, Buji Town, Longgang District, Shenzhen China 518129 Tel: +86 755-89602345 Fax: +86 755-89602394 www.zkteco.com Copyright©2019 ZKTeco CO., LTD. All rights reserved.
