User Manual

MENU Function and How to set the instruction：
MENU
Function
Addr
DMX Address :A001~512
CHnd
Channel Mode:14CH/16CH (4 in1) or 16CH/18CH (6 in 1): press “ENTER” in to and then press “UP”
and “down” to choose and then press “ENTER” to confirm it.
SLnd
ASt→SL 1→SL 2 : press “ENTER” in to and then press “UP” and “down” to choose and then press
“ENTER” to confirm it.
SHnd
Show mode: SH 0~SH3: press “ENTER” in to and then press “UP” and “down” to choose and then
press “ENTER” to confirm it.
SenS
Audio sensitivity select : you can press the “ENTER” in to the fixtures system and then press “UP”
and “down” to choose 0~100 value, usually to choose 60, and then press “ENTER” to confirm it.
bLnd
bLAC(Turn zero)→Atuo→soUn→hoLd(Keep the last state control), please User no set it
Led
LCD display take on or take off select: press “UP” or “down” to choose it in “on” or “off ”.
diSP
Display positive/reverse: please User no set it
rPAn
X motor positive settings: please User no set it
rtiL
Y motor positive settings: please User no set it
rSet
Fixture Reset: You can press “ENTER” to Reset the fixture.
How to control the fixture
1、 DMX512 controller
2、 Master/slave operation
1、DMX512 controller
The fixtures only accepts the DMX512 signal of international standard to control the system. When you run the fixture, all The
fixture must set in the same channels ( CH14 or CH16 channels),Then according to connect you need the fixtures , then turn
on the power, the fixtures will begin to work and all the fixtures DMX LED light Strobe , in this times the all the fixtures have
accept the DMX512 signal.
2、 Master/slave operation
The will allow you to link 26 fixtures together ,under without a controller. in this mode, only one fixture as master, other fixtures
are slave. Notice: When you use this mode, all the fixtures must set in the same channels ( in CH14 or CH16 channel), Then
according to connect you need the fixtures as the below, then turn on the power, the fixtures will begin to work, in this time, the
master fixture Auto LED light or Sound LED light was be turn on, other Slave fixtures Slave LED light be turn on
DMX Operation
The Fixture has 14/16 (4 in1) or 16/18 (6 in 1) two DMX channel mode：
Channel control mode:
Channel
Value
Function
(4 in 1)
(6 in 1)
CH1
CH1
000～255
Adjust Pan motor movement
CH2
CH2
000～255
Adjust Tilt motor movement
CH3
CH3
000～255
PAN/TILT Speed
CH4
CH4
000～255
Dimmer:0～100%
CH5
CH5
000～255
Control the light strobe , the strobe speed from slow to fast
CH6
CH6
0～255
Red color Dimmer:0～100%
CH7
CH7
0～255
Green color Dimmer:0～100%
CH8
CH8
0～255
Blue color Dimmer:0～100%
CH9
CH9
0～255
White color Dimmer:0～100%
CH10
0～255
Orange color Dimmer:0～100%
CH11
0～255
UV color Dimmer:0～100%
CH10
CH12
0～015
Use in other channel
016~044
Motor Auto SH 3
045~074
Motor Auto SH 2
075~104
Motor Auto SH 1
105~128
Motor Auto SH 0
129~157
Motor sound SH 3
158~187
Motor sound SH 2
188~217
Motor sound SH 1
218~255
Motor sound SH 0
CH11
CH13
0～255
Motor sound Sensitivity: 0～100%
CH12
CH14
000
Use in other channel
000~007
LED gradual change
008~039
LED Auto Effect 1
040~074
LED Auto Effect 2
075~108
LED Auto Effect 3
109~140
LED Auto Effect 4
141~168
LED sound Effect 1
169~197
LED sound Effect 2
198~226
LED sound Effect 3
227~255
LED sound Effect 4
CH13
CH15
000~255
LED sound Sensitivity: 0～100%
CH14
CH16
0～255
Reset