B ath F aucets Installation Guide and Users Manual
ZLINE created a wide range of faucet solutions delivering comfortable elegance and undeniable quality down to the smallest detail. Brass housing allows ZLINE faucets to be durable and provides sophistication. It’s what’s on the inside that counts. Behind the scenes, ZLINE’s main focus is improving water efficiency. The faucets are manufactured with carefully hand selected materials that undergo over 50,000 unit tests, well over the industry standard for certification of 15,000 tests. 1.
TABLE OF CONTENTS SAFETY INSTRUCTIONS 1 Prior to Installation Safety Tips Installation Preparation Care and Maintenance Notes SINGLE HANDLE/CENTERSET FAUCETS 3 Parts Tools Models: 31-0301 (Washoe Series) 31-0308 (Diamond Peak Series) 31-0302 (North Lake Series) 31-0303 (South Lake Series) 31-0304 (Aloha Series) 31-0296 (Carnelian Series) 31-0300 (Donner Series) 31-0307 (Vikingsholm Series) 31-0306 (Heavenly Series) 31-0305 (Zephyr Series) 31-0298 (Eagle Falls Series) 31-0297 (Homewood Series) 31-02
TABLE OF CONTENTS DOUBLE HANDLE FAUCETS 17 Parts Tools Models: 26-0075 (Marlette Series) 26-0071 (Alpine Series) 26-0070 (Fallen Leaf Series) 26-0072 (Crystal Bay Series) 26-0073 (Eldorado Series) 26-0074 (Emerald Bay Series) Assembly TROUBLESHOOTING 25
Safety Instructions Prior to Installation Make sure that the cold and hot water lines are turned off. Wrap all threaded connections with plumber’s tape. Always wrap in a clockwise direction. Cover your drain to avoid losing parts. Do not disassemble the main faucet body, as it has been installed and commissioned correctly and precisely before delivery to the factory. To keep the faucet from jamming, flush the water pipe before installation. Operating conditions: Working pressure at 0.05-1.
NOTES Faucet Model: Purchase Order #: Date: 2
SINGLE HANDLE/CENTERSET FAUCET 1. 2. 3. 4. 1. Body 2. C Washer 3. C Washer 4. Lock Nut 5. 6. 7. 1. Body 2. Washer 3. Washer 4. Nut 5. Pop-up 6. Washer 7. Flat washer 8. Nut 8. 5. Pop-up 6. Washer 7. Flat Washer 8. Nut 1. Body 2. Washer 3. Washer 4. Nut 5.
SINGLE HANDLE/CENTERSET FAUCET Tools: Time required: Wrench Phillips-head screwdriver +/- 45 minutes Pliers Legend: Hot Water Cold Water Warning Plumber’s Tape Grease 4
SINGLE HANDLE FAUCET Single Handle Faucet Models 31-0301 (Washoe Series) 31-0308 (Diamond Peak Series) 5
SINGLE HANDLE FAUCET Single Handle Faucet Models 31-0302 (North Lake Series) 31-0303 (South Lake Series) 6
SINGLE HANDLE FAUCET Single Handle Faucet Models 31-0304 (Aloha Series) 31-0296 (Carnelian Series) 7
SINGLE HANDLE FAUCET Single Handle Faucet Models 31-0300 (Donner Series) 31-0307 (Vikingsholm Series) 8
SINGLE HANDLE FAUCET Single Handle Faucet Models 31-0306 (Heavenly Series) 31-0305 (Zephyr Series) 9
SINGLE HANDLE FAUCET Single Handle Faucet Models 31-0298 (Eagle Falls Series) 31-0297 (Homewood Series) 10
SINGLE HANDLE FAUCET 31-0295 (Spooner Series) 11
CENTERSET FAUCET Centerset Faucet Models 21-0005 (Baldwin Series) 12
SINGLE HANDLE/CENTERSET FAUCET Loosen the fixing nut and screws for the handles and put aside. Mount faucet to counter top. Secure the hardware into place. Secure the hoses to the hot (red) and cold (blue) lines appropriately.
SINGLE HANDLE/CENTERSET FAUCET Clear area before inserting pop-up drain stopper. Remove the washer, flat washer, and nut from the pop-up. Insert the pop-up from above and tighten the nut and washers below to secure to the counter top. FOR MODELS WITH LIFT ROD Set the flat rubber gasket over the drain hole in your sink, then insert the flange into the drain hole. Insert the stopper tailpiece from above. Position the tailpiece hole to align with the hole to the side of the body.
SINGLE HANDLE/CENTERSET FAUCET Connect the drain lever by threading it into the hole on the side of the body. The lever must pass through the hole in the stopper tailpiece to function properly. Position the drain so that the lever is facing the back of the fixture, in line with the faucet’s lift rod. (See STEP 10) 15 If not already installed, insert the faucet’s lift rod into its designated hole on the back of the faucet. Attach the extension rod.
SINGLE HANDLE/CENTERSET FAUCET Connect the lift rod and the drain lever with the included attaching clip. Use a screwdriver to secure but do not overtighten the link. Once connected, to open the drain, push down. To close the drain, pull up. Fill your sink to check for any leaks and to ensure that the drain is functioning properly.
DOUBLE HANDLE FAUCET 5. 1. 6. 7. 8. 9. 10. 11. 12. 13. 2. 3. 4. 1. Faucet Handle 2. Washer 3. Washer 4. Lock Nut 5. Body 6. Washer 7. Washer 17 8. Nut 9. Adapter 10. Pop-up 11. Washer 12. Flat Washer 13.
DOUBLE HANDLE FAUCET Tools: Time required: Wrench Phillips-head screwdriver +/- 45 minutes Pliers Legend: Hot Water Cold Water Warning Plumber’s Tape Grease 18
DOUBLE HANDLE FAUCET Double Handle Faucet Models 26-0075 (Marlette Series) 26-0071 (Alpine Series) 19
DOUBLE HANDLE FAUCET Double Handle Faucet Models 26-0070 (Fallen Leaf Series) 26-0072 (Crystal Bay Series) 20
DOUBLE HANDLE FAUCET Double Handle Faucet Models 26-0073 (Eldorado Series) 26-0074 (Emerald Bay Series) 21
DOUBLE HANDLE FAUCET Loosen the fixing nut and screws for the handles and put aside. Mount handles to the counter top. Secure the hardware into place with the Base O-ring, nuts, and screws. Loosen the fixing nut, washers, and adapter from the body and put aside.
DOUBLE HANDLE FAUCET Insert the body into the counter top from above and secure with nuts and washer from below. Secure the hardware into place. SPOUT Secure the spout hose lines from the hot and cold water fixtures. 23 Secure the hoses to the hot (red) and cold (blue) lines appropriately.
DOUBLE HANDLE FAUCET Clear area before inserting pop-up drain stopper. Remove the washer, flat washer, and nut from the pop-up. Insert the pop-up from above and tighten the nut and washers below to secure to the counter top. Review the diagram to understand the hot, cold, and open settings.
TROUBLESHOOTING Problem Possible Cause Solution There is leakage under the The locking nut has Unscrew the lever on the handle. come loose. handle by hand. Loosen set screw with a hex wrench. Remove the handle and unscrew trim cap by hand. Tighten locking nut with an adjustable wrench. Water will not shut off Cartridge may be Unscrew the level on the completely. defective. handle by hand. Loosen set screw with a hex wrench. Remove the handle and unscrew trim cap by hand.
Kitchen and Bath Three Locations: 350 Parr Circle Reno, NV 89512 916 Delaware Avenue Marysville, OH 43040 319 Rowland Mill Road Bruceton, TN 38317 www.zlinekitchen.