B ath F aucets Installation Guide and Users Manual
ZLINE is fueled by a passion for innovation; A relentless pursuit of bringing the highest end luxury designs and professional features into everyone's homes. Because we continually strive to improve our products, we may change specifications and designs without prior notice. WARNING: This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
Inspired by the clear, serene waters of the stunning Lake Tahoe, ZLINE Bath Faucets provide the ultimate luxury experience. ZLINE Faucets are offered in a wide selection of contemporary styles and designer finishes. With ergonomic control in mind, these faucets offer the perfect amount of aerated water pressure at 1.8 gal/min, allowing for an eco-friendly and efficient washing experience.
WARRANTY COVERAGE ZLINE Kitchen and Bath faucets have a limited lifetime warranty from the original purchase date for the original purchaser of the product. TERMS This warranty applies only to the original purchaser of a faucet installed for normal residential use. This is defined as a single-family, residential dwelling in a noncommercial setting.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS 1 SINGLE HANDLE & CENTERSET FAUCETS 2 DOUBLE HANDLE FAUCETS 8 WALL MOUNTED DOUBLE HANDLE FAUCETS 13 TROUBLESHOOTING 18
SAFETY INSTRUCTIONS PRIOR TO INSTALLATION • Make sure that the cold and hot water lines are turned off. • Wrap all threaded connections with plumber’s tape. Always wrap in a clockwise direction. • Cover your drain to avoid losing parts. • Do not disassemble the main faucet body, as it has been installed and commissioned correctly and precisely before delivery to the factory. • To keep the faucet from jamming, flush the water pipe before installation. Operating conditions: Working pressure at 0.05-1.
BEFORE INSTALLATION Single handle & Centerset 1. 5. 5. Pop-up 6. Washer 7. Flat Washer 8. Nut 5. Single Handle & Centerset Product Specifications 4. Body Washer Washer Nut Pop-up 8. 1. 3. 1. 2. 3. 4. 5. 7. 4. 2. Body Washer Washer Nut Pop-up Washer Flat washer Nut 6. 2. 3. 1. Body 2. C Washer 3. C Washer 4. Lock Nut 1. 2. 3. 4. 5. 6. 7. 8.
BEFORE INSTALLATION Single Handle & Centerset Tools Needed: Time required: Wrench Phillips-head screwdriver +/- 45 minutes Single Handle & Centerset Installation Tools Pliers 3 Legend: Hot Water Cold Water Warning Plumber’s Tape Grease
INSTALLATION Single Handle & Centerset Ø 34 mm (1.34”) Min Ø 37 mm (1.46”) Max Loosen the fixing nut and screws for the handles and put aside. Mount faucet to counter top. 11# 10# Secure the hardware into place. Secure the hoses to the hot (red) and cold (blue) lines appropriately.
Single Handle & Centerset Installation INSTALLATION Single Handle & Centerset 5 Clear area before inserting pop-up drain stopper. Remove the washer, flat washer, and nut from the pop-up. Insert the pop-up from above and tighten the nut and washers below to secure to the counter top. FOR MODELS WITH LIFT ROD Set the flat rubber gasket over the drain hole in your sink, then insert the flange into the drain hole. Insert the stopper tailpiece from above.
INSTALLATION Single Handle & Centerset Connect the drain lever by threading it into the hole on the side of the body. The lever must pass through the hole in the stopper tailpiece to function properly. If not already installed, insert the faucet’s lift rod into its designated hole on the back of the faucet. Attach the extension rod. Position the drain so that the lever is facing the back of the fixture, in line with the faucet’s lift rod.
INSTALLATION Single Handle & Centerset 2 1 Single Handle & Centerset Installation Connect the lift rod and the drain lever with the included attaching clip. Use a screwdriver to secure but do not overtighten the link. 7 Once connected, to open the drain, push down. To close the drain, pull up. Fill your sink to check for any leaks and to ensure that the drain is functioning properly.
BEFORE INSTALLATION Double Handle Faucet 5. 1. 6. 7. 8. 9. 10. 11. 12. 13. 2. 3. 4. 8. Nut 8. 9. Nut Adapter 9. Adapter 10. Pop-up 10. Pop-up Washer 11 1.1.Washer 12. Washer 12.FlatFlat Washer 13. Nut 13. Nut Double Handle Product Specifications 1. Faucet Handle 1. Washer Faucet Handle 2. 2. Washer 3. Washer 3. Washer 4. Nut 4. Lock Lock Nut 5. Body Body 5. 6. Washer 6. Washer 7. Washer 7.
BEFORE INSTALLATION Double Handle Faucet Tools Needed: Time required: Wrench Phillips-head screwdriver +/- 45 minutes Pliers Double Handle Tools Legend: 9 Hot Water Cold Water Warning Plumber’s Tape Grease
INSTALLATION Double Handle Faucet 102 mm - 153 mm 102 mm - 153 mm 4” - 6” 4” - 6” 3- Ø 28 mm (1.1”) Min 3- Ø 33 mm (1.3”) Max Mount handles to the counter top. Secure the hardware into place with the Base O-ring, nuts, and screws. Loosen the fixing nut, washers, and adapter from the body and put aside. Double Handle Installation Loosen the fixing nut and screws for the handles and put aside.
INSTALLATION Double Handle Faucet Insert the body into the counter top from above and secure with nuts and washer from below. Double Handle Installation SPOUT SPOUT 11 Secure the hardware into place. IN IN 9/16-24UNEF IN SPOUT Secure the spout hose lines from the hot and cold water fixtures. Secure the hoses to the hot (red) and cold (blue) lines appropriately.
INSTALLATION Double Handle Faucet Clear area before inserting pop-up drain stopper. Remove the washer, flat washer, and nut from the pop-up. Open Insert the pop-up from above and tighten the nut and washers below to secure to the counter top. 90° Open Review the diagram to understand the hot, cold, and open settings.
Wall Mounted Double Handle Product Specifications BEFORE INSTALLATION Wall Mounted Double Handle Faucet 13 1. 2. 3. 4. 5.
BEFORE INSTALLATION Wall Mounted Double Handle Faucet Tools Needed: Time required: Wrench Phillips-head screwdriver +/- 45 minutes Hacksaw Legend: Plumber’s Tape Wall Mounted Double Handle Tools 14
INSTALLATION Wall Mounted Double Handle Faucet 1 2 Ø6 15 3- Ø 1 1/4” 3- Ø 32 mm MAX MIN Wall Mounted Double Handle Installation Plan where the faucet will hang on the Mount rough-in to the wall. wall. 1/2-14PNT Max 95 mm (3 3/4”) Min 70 mm (2 3/4”) Finished wall Secure the rough-in into place. Use plumber’s tape to prevent leaks. See Figure 1. Figure 1.
INSTALLATION Wall Mounted Double Handle Faucet Cartridge adapter 2-Max 40 mm (1 9/16”) 2-Min 30 mm (1 3/16”) Min 28 mm (1 1/8”) Max 35 mm (1 3/8”) Sleeve adapter 2-Max 16 mm (5/8”) 2-Min 8 mm (5/16”) Finished wall Figure 2. Prepare rough-in for faceplate, handle, and spout. Connect the faceplate and secure into place. Wall Mounted Double Hand Installation Tighten rough-in components. See Figure 2.
INSTALLATION Wall Mounted Double Handle Faucet 90° 90° Open Open Open Wall Mounted Double Handle Installation Connect the handles and secure into place. 17 90° 90° Open Open Review the diagram to understand the hot, cold, and open settings. Connect the spout and secure into place.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTIONS Unscrew the lever on the handle by hand. Loosen set screw with a hex There is leakage under the The locking nut has come loose. handle. wrench. Remove the handle and unscrew trim cap by hand. Tighten locking nut with an adjustable wrench. Unscrew the level on the handle by hand. Loosen set screw with a hex Water will not shut off wrench. Remove the handle and Cartridge may be defective. completely. unscrew trim cap by hand.
Three Locations: 350 Parr Circle Reno, NV 89512 916 Delaware Avenue Marysville, OH 43040 427 Rowland Mill Road Bruceton, TN 38317 www.zlinekitchen.com 1-614-777-5004 2.1.