Designer Wall Range Hood Installation Installation Tutorial Video 9
Designer Wall Range Hood Installation Please unpack your range hood when it is delivered and inspect to ensure all parts are included. Parts Supplied: 1. Main Hood With All Lights and Button Banks Pre-installed 2. Chimney 3. Transition Piece (For 6˝ or 8˝) 4. Baffle Filters 5. Flexible Duct (For 6˝ or 8˝) 6. Packet of Screws and Anchors 7. Top Mounting Bracket 8. Crown Molding Bracket 9. Crown Molding 10.
Designer Wall Range Hood Installation *The recommended height to install your hood is 30˝ minimum and 36˝ maximum above the cooktop. *For Outdoor (304 Series) hood installation: The unit must be installed at a minimum of 36˝ above the grill. 1 2 Find the center of the wall where you are installing the hood. Make sure there is sufficient bracing to hold the weight of the hood. Mark your center line and measure out from the center to find your two mounting points.
Designer Wall Range Hood Installation Designer Wall Range Hood Installation 5 Make your electrical and ducting connections. Try and minimize the use of elbows. More elbows and longer runs create higher static pressure. The hood comes with a grounded three prong plug that can either be direct wire or plugged into a 20amp. circuit. (Figure 4) Figure 4 Figure 5 6 Install the transition piece securing it with screws provided.
Designer Wall Range Hood Installation 8 Cut chimney to height needed. (Figure 7) Figure 7 9 Install the chimney on top of the hood. Secure the lower portion with the provided screw at the bottom. (Figure 8) Figure 8 10 Slide crown molding over mounting bracket.
Installing Crown Moldings If using a crown molding follow instructions before attaching ducting and chimney sections. 14 1 Attach crown molding bracket to ceiling using hardware provided. 2 Attach ducting and electrical connections. 3 Attach chimney sections to the range hood then connect to crown molding bracket. 4 Slide crown molding onto crown bracket and secure into place.
Wall Range Hood Installation Installation Tutorial Video 4
Wall Range Hood Installation Please unpack your range hood when it is delivered and inspect to ensure all parts are included. E B F Parts Supplied: 1. Main Hood With All Lights and Button Banks Pres-installed 2. Adjustable Stainless Chimney Cover 3. Transition Piece (For 6˝ or 8˝) 4. Baffle Filters 5. Flexible Duct (For 6˝ or 8˝) 6. Packet of Screws and Anchors 7. Top Mounting Bracket 8.
Wall Range Hood Installation *The recommended height to install your hood is 30˝ minimum and 36˝ maximum above the cooktop. *For Outdoor (304 Series) hood installation, the unit must be installed at a minimum of 36˝ above the grill. 1 2 Find the center of the wall where you are installing the hood. Make sure there is sufficient bracing to hold the weight of the hood. Mark your center line and measure out from the center to find your two mounting points.
Wall Range Hood Installation 5 Install the transition piece securing it with screws provided. (Figure 4) 6 Make your electrical and ducting connections. Try and minimize the use of elbows. More elbows and longer runs create higher static pressure. The hood comes with a grounded three prong plug that can either be direct wire or plugged into a 20amp. circuit. (Figure 5) Figure 4 Figure 5 7 Connect the ducting to the transition piece using ring to hold into place. Attach ducting to the range hood.
Wall Range Hood Installation 8 Install the two part chimneys on top of the hood. Slide the inside section up until the vertical vent slots are visible, attach top portion to mounting bracket with screws. Secure lower chimney portion to the hood with screws provided. (Figure 7) 9 Install plastic drip cup by sliding into brackets located at the bottom of the motor. Install ◆baffle channel and baffle filters. (Figure 8) ◆Not all models include baffle channels.