Installation Guide and Users Manual

22
Attach the exhaust adaptor to the rear of the
oven by sliding it into the guides at the top
cent er of t h e back of th e oven.
AFTER: Fan Blade
Openings Facing Back
Place the blower unit back into the opening.
Repl ace the bl ower pl ate i n the same posi ti on
as bef or e wi t h t he scr ew. Make sur e the scr ew
is tight.
Roll the blower unit 90° so that fan blade
openings are facing out the back of the
mi cr owave.
ADAPTING MICROWAVE
BLOWER FOR OUTSIDE
BACK EXHAUST (cont.)
B5.
Rotate blower unit counterclockwise 180°.
Bef ore Rot at i on After Rotation
Gen t l y remove the wir es f rom th e gr ooves.
Rerout e t he wi r es thr ough gr ooves on other si de
of the blower unit.
Bef ore Rerout i ng Aft er Rerout i ng
Wires Rout ed Through Ri ght Side
Wires Rout ed Through Left Side
Back of
Microwave
Back of
Microwave
Bl ower Pl at e
Bl ower Motor
Screw
Secur e the bl ower uni t to the mi cr owave with
the original screw.
Bef ore Rol l i ng After Rolling
Back of
Microwave
End A
End B
Back of
Microwave
Back of
Microwave
CAUTION: Do not pull or stretch the blower
unit wiring. Make sure the wires are not
pinched, and that they are properly secured.
NOTE: The blower unit exhaust
openings should match exhaust
openings on rear of microwave oven.
Inst allat ion Inst ruct ions
Push in securely until it is in the lower locking
t abs. Take car e t o assur e th at t he damper hi n ge
is installed so that it is at the top and that the
damper swings f reel y.
Gui de
Gui de
Adaptor
Locking Tabs
Back of
Microwave
4
5
6
11
Back of mircrowave
Knockout Plates:
Snip all 4 webs on
each knockout panel
and remove t he metal
knockouts for rear airflow.
Please take care to
remove any sharp edges
created from removing
the knockout plates.
7
8
9
10
with snips. (For some models)
Remove the knockout plates in the back of the unit
EN-18
Attach the microwave oven to the top cabinet.
Inst allat ion Inst ruct ions
3
MOUNT THE M ICROWAVE
OV EN
B6.
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND TH AT T WO PEOPL E
INSTALL THIS MICROWAVE OVEN.
NO T E: I f your cabi n et i s metal, use th e n yl on
gr ommet around t he power cor d h ole t o pr event
cutting of the cord.
NO T E: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not
used, case damage may occur f r om
over tighteni ng screws.
Insert a self-aligning screw through top center
cabi n et h ole. Tempor ar il y secur e the oven by
turning the screw at least two f ull turns after the
thr eads have engaged. (It will be completely
ti ghtened l ater.) Be sur e to keep power cor d
tight. Be careful not to pinch the cord, especially
when mounting f lush to bottom of cabinet.
8
7
5
Cabi net Front
Cabi net Bot t om Shelf
Tighten the outer two screws to the top of the
microwave oven. (While tightening screws, hold
t h e m icr owave oven i n pl ace agai nst t h e wal l an d
the top cabinet.)
Filler Block
Microwave Oven Top
Equi val ent
to Depth
of Cabi net
Recess
Insert 2 self-aligning screws
through outer top cabinet
holes. Turn two full turns on
each scr ew.
packed with the mi cr owave.
Sel f-Ali gni ng Screw
4
2
Rotate front of oven
up agai nst cabi net
bottom.
NO T E: When mounting the
mi cr owave oven, thr ead
power cord through hole in
bottom of top cabinet. Keep
it tight throughout Steps
1–3. Do not pinch cord or
lift oven by pulling cord.
Lift microwave, tilt it
forward, and hook
slots at back bottom
edge onto four lower
tabs of mounting
pl ate.
1
I nstall gr ease fi lter s. See th e U se &&&&and Care
IMPORTANT: Do not grip or use the handle
or heat shield during installation. Do not
r emove t he cardboar d spacer s between the
heat shield and door.
EN-19
INSTALLATION