Instructions for installation and use English H0402400.
• Read this manual carefully before installing, maintaining or repairing this device! • The symbol indicates important information that must be taken into account in order to avoid risk of personal injury and/or damage to the appliance. • The symbol indicates useful information. Exclusive use: pool water cleaning (must not be used for any other purpose). Warnings Failure to comply with the following warnings can result in permanent injury, electrocution or drowning.
Warnings Failure to comply with the following warnings could cause damage to pool equipment or personal injury. • This product is intended for use with permanently‐installed pools. Do not use with storable pools. A permanently‐installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity.
1. Information before use 1.1 Important Check that your appliance has not been damaged during transport (shocks, broken parts, etc.). If you find any problems don't hesitate to contact your reseller before using the cleaner. 1.
1.4 Package content and assembly of the transport caddy H0402400.
1.5 Immersing the cleaner Do not allow bathing when the cleaner is in the pool. Place the cleaner vertically into the water (1) and move it slightly in all directions so that the air contained in the cleaner escapes (2). It is essential that the cleaner sinks on its own and settles on the pool bottom. Spread out the required length of cable by the pool. For optimum operation we recommend that you place the caddy with the control box at the centre of the pool length (3). 1.
2.
3.3 Removing the cleaner from the water You can use the “remove from pool” mode during the cleaning cycle or at the end of the cycle by using the control box or the remote control (V4 4WD). Using the control box, a short press on the button. The moves towards a pool wall and climbs up to the waterline. message is displayed. The cleaner Using the remote control unit (V4 4WD) : (see § 5.1).
4. Program cleaning cycles for when you are away It is not recommended to unplug the power cord once the programmed cleaning cycles have completed as this will delete the time settings. The time setting will be saved for approximately 2 minutes if the power cord is disconnected. 4.1. Setting the time To set the time, press the button for a longer time (3 seconds). The days of the week begin flashing: Select the current day using the Validate using the , then the leds and . buttons.
To programme a cycle, press the button for a longer time (3 seconds). The led stops flashing The days of the week flash twice. The LED and the current date and time flash. This is a reminder of the current date and time you entered in order to help you to programme. Press to start programming. If the LEDs flash it means that the time setting is not complete. To continue with the cleaning cycle programming, it is essential to set the time first. To do this follow the instructions in § 4.1.
5. Remote control (V4 4WD) 5.1 Using the remote control By default, the remote control is already synchronised with the control box. To power on the remote control press the button for a long time (3 seconds).
6. Maintenance 6.1 Cleaning the filter The cleaner performance can be reduced if the filter is full or dirty. Make sure you clean the filter regularly with clean water for efficient pool cleaning. Filter access "Clean filter" indicator (V4 4WD) If the indicator on the control box lights, it is strongly recommended to clean the filter in order to perfect the cleaning. If the indicator comes on during a cleaning cycle, it will remain on until the end of the cycle. 6.
7. Troubleshooting In the event of malfunction, the control box indicates the error code on the screen. Pressing a key deletes the error code and turns off the control box. The screen switches to standby after 10 minutes. To turn the screen back on, just press any key. When an error is detected, the control box temporarily suspends the programme (the Press the led is turned off). key for a longer period to revalidate the current programming. 7.
7.2 Pre‐diagnosis in the event of a malfunction If your cleaner malfunctions you have access to a menu which gives some indications on the status of your cleaner. This information can be used by your reseller to troubleshoot a possible breakdown. To access the menu the cleaner must not be operational and the display must be on. Press on and simultaneously for at least 5 seconds.
Notes
Zodiac Group Australia Pty Ltd. 219 Woodpark Road, Smithfield NSW 2164 Ph: +612 8786 6800 | FAX +61 2 9756 3987 For more information visit www.zodiac.com.au or call 1800 688 552 ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license. All trademarks referenced herein are the property of their respective owners.
