Instructions for installation and use English H03818-00.
• Read this manual carefully before installing, maintaining or repairing this device! indicates important information that must be taken into account in order to avoid risk • The symbol of personal injury and/or damage to the appliance. • The symbol indicates useful information. • Exclusive use: pool water cleaning (must not be used for any other purpose). Warnings Failure to comply with the following warnings can result in permanent injury, electrocution or drowning.
Warnings Failure to comply with the following warnings could cause damage to pool equipment or personal injury. • This product is intended for use with permanently-installed pools. Do not use with storable pools. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity.
1. Information before use 1.1 Important Ensure that the unit has not been damaged in transit (impact, broken parts, etc.). Please report any damage, however minor, to your retailer immediately, before using. 1.2 Package contents The packaging should contain the following items: • The robot • a transport caddy, • a control unit, • a user manual, 1.3 Assembling the transport trolley • Insert the upper tubes (handles) into the bottom tubes on the cart as shown (1).
• Secure the control unit hook using two bolts and two nuts and tighten with Torx wrench (7). • Place two caps on the wheels (8). • Attach the support blocks to the caddy using four screws (V3 = figure 9; V3 4WD = figure 10). EN • The transport caddy is now ready to use 1.4 Connecting the control unit to the caddy • Position the control unit over the control unit hook on the caddy. • Slide the locking plate clips into the control hook and line up the screw holes (1).
1.5 Technical information Control unit voltage Robot supply voltage Installed load Cable length Cleaner size (WxDxH) Pack size (WxDxH) Weight of cleaner Packed weight Filtering surface Filtration Theoretical width cleaned Theoretical area cleaned Pump output Rate 220-240 VAC, 50 Hz; short-circuit-proof safety isolating type 30 VDC 150 W 18 m 43 x 48 x 27 cm 58 x 58 x 59 cm 11 kg 300 19 kg 3400 cm² medium 38 cm 260 m² / h 16 m³/h 8 m / min 2. Use 2.
2.3 Electrical connection The cleaner control unit is water-resistant, not waterproof. In order to prevent electrocution, which could result in serious injury or death, never submerge the control unit. • Place the control box at a distance of at least 3.5 meters from the pool edge and away from direct sunlight; it can either be placed on the ground or attached to the caddy.
Approximately 15 minutes after the cycle is completed, the light located on the control unit will flash slowly to indicate that the cleaner may be removed from the pool. The 15 minute period allows the motor to cool and will prevent damage to the cleaner. • Remove the cleaner from the pool after the cleaning cycle is completed and store on the caddy. • Never lift the cleaner out of the pool by the floating cable. Always use the handle to remove it from the pool.
3.2 Cleaning and Storing the Cleaner The cleaner must be cleaned regularly using slightly soapy clean water, do not use solvents such a trichloroethylene or its equivalent. Rinse the cleaner generously using clean water. Do not let your cleaner dry in direct sunlight near the pool. The cleaner must be stored on its own caddy, so that it dries quickly. • Place the rear wheels on the caddy side wedges (1). • Roll the unit into place onto the caddy (2).
5. Replacing the Tyres on the Cleaner • Pull on the inside of the old tyre to remove the tyre lip from the wheel (1). • Remove the old tyre (2). • To replace the tyre, position the tyre on the wheel making sure to orient the tyre so that the tyre tread is on the outer side of the wheel (3). The word "inside" is imprinted on the rim of the tyre. Make sure the word "inside" is facing towards the body of the cleaner.
Symptom The cleaner does not stay firmly on the pool bottom. Cause There is air in the appliance casing. Filter is full or dirty. The cleaner does not or no longer climbs the pool sides. Sides of pool are slippery or slimy. Although the water seems clear, microscopic algae, invisible to the human eye, are present in the pool. As a result the pool sides become slippery and prevent the cleaner from climbing. Not supplied with electricity. On startup the cleaner does not move. Unit is turned ON.
Zodiac chlorinators are designed and tested in accordance with International Standard EN 61000-6-1 immunity measurements. They are designed to tolerate minor fluctuations (2000 volts) in power supply that can be reasonably expected to occur in the energy grid. They will not tolerate power surges outside these limits nor will they withstand lightning strikes. 4.
Notes
Notes
Notes
Zodiac Group Australia Pty Ltd. 219 Woodpark Road, Smith eld NSW 2164 Ph: +612 8786 6800 | FAX +61 2 9756 3987 For more information visit www.zodiac.com.au or call 1800 688 552 ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license. All trademarks referenced herein are the property of their respective owners.
