Install Instructions

ManualsBrandsZoeller ManualsPlumbing SuppliesA-Pak Deluxe Alarm System w/ 20' Float Switch, 6' Power Cord, Watertight Cord Connectors

FOR YOUR PROTECTION ALWAYS DISCONNECT FROM POWER SOURCE BEFORE HANDLING. The “A-Pak” Alarm

system has a double insulated plastic enclosure for your protection and is supplied with a 2-prong plug.

SPECIFICATIONS

This alarm system monitors liquid levels in lift pump chambers, sump pump basins, holding tanks, sewage, agricultural

and other non-potable water applications. It features a red warning light, green “power on” light, alarm test switch and

horn silence switch. “A-Pak” primary voltage is 120 VAC, 60 Hz, 2.4 watts max (alarm condition) (circuit is not supervised).

Secondary voltage is 9 VDC (circuit is not supervised). Battery backup power is 9 VDC. NOTE: 9V battery is not included

and must be purchased separately.

NOTE: The alarm panel plugs into a standard household 120 VAC socket. DO NOT plug “A-Pak” Alarm System into the

same circuit as the pump. The “A-Pak” Alarm System should be connected to a circuit separate from the pump circuit.

Push test button to check alarm panel for operation.

ALARM PANEL INSTALLATION

1) Before installing alarm panel, remove battery cover on side of alarm panel and install a 9V battery. (not included)

2) Mount the alarm panel indoors with screws provided. NOTE: The mounting screw is to be located over a wall stud or

used with a wall anchor sized for a #8 x 1.25 self tapping screw.

3) Hang the panel by the keyhole in the back of the alarm enclosure and install the second screw between the tabs

located on bottom of the enclosure.

4) Using the provided cable clamp, secure the power cord to the outlet as shown (see Fig. A). Use existing receptacle

faceplate screw and supplied washer.

SECTION: 6.10.100

FM0483

0112

Supersedes

1111/2

PN 1012302 Rev. F

MODEL TAAB

Product information presented

here reects conditions at time

of publication. Consult factory

regarding discrepancies or

inconsistencies.

MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347

SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961

(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624

visit our web site:

www.zoeller.com

Your Peace of Mind is Our Top Priority

NOTICE TO INSTALLER: Instructions must remain with installation.

Figure A

SK2148

“A-PAK” ALARM SYSTEM INSTALLATION INSTRUCTIONS

CONTROL SWITCH INSTALLATION

MECHANICAL FLOAT SWITCH

(10-1494, 10-2614)

1) Place cord into clamp and secure to discharge pipe as shown in clamp detail (see

Fig. B). NOTE: Do not install the cord under the hose clamp.

2) Tighten the hose clamp with a screwdriver. NOTE: Do not over tighten; over tightening

may cause damage to the plastic clamp.

3) Make sure the oat cable is not allowed to touch the excess hose clamp band during

operation.

4) The oat switch must be suspended seven inches below desired activation level. (see Fig. D)

5) Allow system to cycle to ensure proper operation.

FACEPLATE SCREW

WASHER

CABLE CLASP

3.5 INCH

TETHER LENGTH

FOR DOUBLE

FLOAT

3.5 INCH

MINIMUM

TETHER LENGTH

FOR PUMP

SWITCH

SK1301D

Figure B

CLAMP DETAIL

(Tether Length Non-Adjustable)

LIFT PUMP

Suspend control switch above pump turn on level. If a pump failure causes

high-level condition, the A-Pak Alarm System will activate (see Fig. C).

Figure C

SEWAGE HOLDING TANK

Suspend control switch into tank seven inches below desired

alarm level. A-Pak Alarm System will activate if oat ascends to

alarm level (see Fig. D).

SK1301b

Figure D

TEST

SILENCE

ALARM

POWER ON

ZOELLER

ALARM

ZOELLER

PUMP "ON"

PUMP "OFF"

FIBERGLASS

OR POLYETHYLENE

BASIN

"ON" LEVEL

VARIABLE LEVEL

CONTROL SWITCH

LEVEL

4" OF GRAVEL

ALARM

ZOELLER

TO POWER SUPPLY

UNICHECK

"DO NOT" PLUG "A-PAK ALARM SYSTEM

INTO THE SAME CIRCUIT AS THE PUMP

NOTE:

SK2376

Summary of content (4 pages)

PAGE 1
NOTICE TO INSTALLER: Instructions must remain with installation. SECTION: 6.10.100 Your Peace of Mind is Our Top Priority ® FM0483 0112 Supersedes 1111/2 ® Product information presented here reflects conditions at time of publication. Consult factory regarding discrepancies or inconsistencies. MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347 SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961 (502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624 visit our web site: www.zoeller.
PAGE 2
CONTROL SWITCH INSTALLATION VERTICAL REED FLOAT SWITCH (10-2613, 10-2615) Do not install switch in direct line of incoming liquid. 1) Place the clamp into the switch housing as shown. (see Fig. E). 2) Locate clamp at desired activation level and secure the clamp to the discharge pipe as shown (see Fig. E). NOTE: Do not install cord under hose clamp. 3) Tighten the hose clamp using a screwdriver. Over tightening may result in damage to the switch housing. 4) Check installation.
PAGE 3
MODELS 10-2614 AND 10-2615 “A-PAK” ALARM SYSTEMS WITH AUXILLIARY CONTACTS WIRING INSTRUCTIONS ELECTRICAL SHOCK HAZARD - Disconnect all power sources before servicing. Failure to do so could result in serious injury or death. 1) Remove the three screws from the back of the enclosure as shown in Fig. H. 2) Remove the back of the enclosure. Note the position of the power cord in the enclosure. The cord will need to be located in the same manner when the enclosure back is replaced.
PAGE 4
BELL ALARM SYSTEMS TYPICAL INSTALLATION AND WIRING INSTRUCTIONS All electrical systems must be installed by a qualified licensed electrician according to the National Electrical Code and all other applicable codes. Model Voltage dB @ 10’ 10-0015 115V 74 10-0016 230V 74 10-0028 115V 78 Bell Transformer o o o Float o o o o NOTE: Utility box and cordage sold separately. Bell Alarms 10-0015 and 10-0016 are designed to be used with Alarm Packs 10-2614 and 10-2615.