Installation Sheet

ManualsBrandsZoeller ManualsTools and HardwareFlow Mate Collection 188-0046 1.5 HP High Head Effluent Pump with Non-Automatic Cord

180, 190 Series

Features

The Flow-Mate series of submersible pumps is designed for use in residential or

light commercial dewatering applications and can be used to transfer

groundwater or effluent. These durable cast iron pumps include a powder

coated epoxy finish to prevent corrosion, and are designed to provide great heat

dissipation from the motor, ensuring a long service life. As with every Zoeller

pump, each one is 100% pressure-tested, submerged and run to ensure quality

and reliability for years of trouble-free performance!

Automatic models include a float-operated, 2-pole mechanical switch, a

stainless steel float guard and switch arm, and a buoyant polystyrene float.

Nonautomatic units are ideal for use in septic systems, low pressure pipe

(LPP), and enhanced flow STEP systems.

For nonautomatic pumps, variable level control systems and containers of

various sizes are available for longer cycles.

Double seal models are available to prevent leaks and damage to seals or

bearings during dry run conditions as well as improve bearing lubrication.

Includes a stainless steel handle for easy installation and removal.

All models are hermetically sealed to be watertight, dust-tight, and completely

submersible.

Reserve Powered Design: For unusual conditions, a reserve safety factor is

engineered into the design of every pump.

Specifications

Motor Characteristics

Motor 1 - 2 HP

Voltage 200 - 575 V

Phase 1 or 3 Ph

Hertz 60 Hz

RPM 3450 RPM

Type Permanent split capacitor or 3 Ph

Insulation Class B/185 & 4185, Class F/186-191 & 4186-

4189

Amps 3.3 - 20.5 Amps

Pump Characteristics

Operation Automatic or nonautomatic

Auto On/ Off Points 15-3/4" (400 mm) / 5-1/4" (133 mm)

Discharge Size 1-1/2" NPT (optional 2" or 3" flange)

Solids Handling 180/4180: 3/4" (19 mm), 191: 5/8" (15 mm)

spherical solids

Cord Length 20' (6 m) standard

Cord Type UL listed, 3-wire neoprene cord and plug (1

Ph) or 4-wire cord with no plug (3 Ph)

Max Head 137' (42 m)

Max Flow Rate 145 GPM (549 LPM)

Max Operating Temp 130 °F (54 °C), (model WD189 120 °F [49 °C])

Cooling Oil filled

Motor Protection Auto reset thermal overload (1 Ph)

Materials Characteristics

Cap Cast iron

Motor Housing Cast iron

Pump Housing Cast iron

Base Cast iron

Upper Bearing Ball bearing

Lower Bearing Ball bearing

Mechanical Seals Carbon and ceramic

Impeller Type Non-clogging vortex

Impeller Bronze

Hardware Stainless steel

Motor Shaft 1117 carbon steel or 416 stainless steel*

Gasket Neoprene

FM0659_Ea

Summary of content (3 pages)

PAGE 1
80, 190 Series Specifications Motor Characteristics Motor 1 - 2 HP Voltage 200 - 575 V Phase 1 or 3 Ph Hertz 60 Hz RPM 3450 RPM Type Permanent split capacitor or 3 Ph Insulation Class B/185 & 4185, Class F/186-191 & 41864189 Amps 3.3 - 20.
PAGE 2
180, 190 Series Model Model Number Seal Mode Volts Phase Amps HP Hz Lbs Kg D185 / H185 Single Auto 230 / 200 1 9.8 / 11.5 1 60 85 / 86 38 / 39 E185/E4185 Single / Dbl Non 230 1 9.8 1 60 85 / 92 38 / 41 I185/I4185 Single / Dbl Non 200 1 11.5 1 60 85 / 92 38 / 41 F185/F4185 Single / Dbl Non 230 3 7.4 1 60 85 / 92 38 / 41 J185/J4185 Single / Dbl Non 200 3 7.5 1 60 85 / 92 38 / 41 G185/G4185 Single / Dbl Non 460 3 3.
PAGE 3
180, 190 Series Model Number Seal Mode Volts Phase Amps HP Hz Lbs Kg E191 Single Non 230 1 14.5 2 60 87 39 *Single seal models are built with a carbon steel motor shaft, and double seal models are built with a stainless steel motor shaft. WD models controlled by integral variable level pump switch. H, I, J, F, G, BA models have no molded plug. Cords available in 25' (8 m) 35' (11 m) and 50' (15 m).