~t7 RHINOVIRUS ®Be sure that all parts are attached Ee : firmly before each use. Name of Each Part Spring Holder Mouth TN Spout —¢ interior ® The illustrations used in this instruction manual may vary from the actual product you have purchased.
Please follow these instructions to prevent scalding, Important Safeguards deterioration and discoloration of beverages, and malfunction or staining of the Carafe. Keep out of the reach of infants and small children. Do not slow them to play with this product. Mishandling may cause injury or scalding. Do not use In direct sunlight er near open flames from sources such as stoves. Doing so may cause scalding, deformation or discoloration of the Carafe.
(continued) Consume beverages within the same day to prevent spoilage. Leaving a beverage in the Carafe for an extended period of time may cause spoilage and increase gas pressure inside the Main Body, causing the Stopper Set to pop off and beverages fo spill, resulting in injury. After attaching the Stopper Set to the Main Body, the Pour Lever several times io make sure that the Lower Stopper Set is also correctly attached.
n ® Before uss, rinse the Stopper Set and the Interior (VS the Carafe thoroughly with lukewarm water. © The first time you use the product you may notice the smell of plastic. This is normal and will gradually fade away. © Always make sure that all parts of the Stopper Set are properly attached before use. Failure to do so may cause contents to leak. (See py. 7-8 “Reassembling the Stopper Set’ for details) © Keep the Carafe upright when transporting it.
ng the Carafe (continued) Pouring beverages: (Hold the handle and press down @Keep the Pour Lever pressed the Pour Lever while keeping the down and tilt the Carafe to Main Body upright. pour. (D While holding and pressing the Seashell the Pour Lever. Pour Lever, stand the Carafe upright. EEE If the Pour Lever is released while the Carafe Is tilted, beverages will sit in the Stopper Set and cause leakage during use, resulting in burns or stains. if the Pour Lever is released while the Carafe Is tilted.
Disassembling the Stopper Set Ss N Remove the Upper Stopper Set. @Lift the Upper Stopper Set to remove. (Hold the Upper Stopper Set and rotate the Lower Stopper Set in the direction arrow. Remove the Spring Holder. (Hold the bottom of the @While holding the bosom of the Stopper Stopper Valve Set with Valve Set, firmly hold and push down on your finger so it does not the Spring Holder, tum it 80 degrees in move. the direction indicated by the arrow, and remove the Spring Holder and Spring.
Disassembling the Stopper Set (continued) r ~ Remove the Stopper Packing and Valve Packing. (Push the Stopper @Pinch the Stopper (“Do ret remove the Packing so that it is Packing at the notch | salter packing on the loose at the notch. and remove the Sipper Naive Set. @ Stopper Packing. Valve Packing \ Push Or Notch 7 4 Attach the packing. Stopper Packing Valve Packing Note the top and bottom There is ne top or bottom. of the packing. 8 i The flat A {surface | Opening i should be | font op.
Reassembling the Stopper Set (continued) 7 a Attach the Stopper Valve Set. insert the Stopper Valve Set to @Hold the bottom of the Stopper the Lower Stopper Set, place the Valve Set, push in the Spring spring, then the Spring Holder. Holder and rotate it 30 degrees in the direction indicated by the arrow to attach i to the Stopper Valve Set. Spring Holder Turn while pushing down “Writing on top 1 [ed Align the Tab on the Spring Hold with finger Holder with the Opening on the Stopper Valve.
Clean the product after each use to prevent odors, stain, mold, and to keep the product sanitary. @Airways disassemble the Carafe before cleaning. {See pg. 8-7) O Wash with warm water and mild dish washing liquid using a soft sponge. 2 (I @Rinse, shake a few times, gently wipe away any moisture, and allow to dry. S101 @ Disassemble the Stopper Set and remove the Stopper Packing LT and Valve Packing first, then wash and dry. See pg. 6-7 “Disassembling the Stopper Set” for details.