Operation Manual

The 3000 incorporates a so-called RTM (real-time modulation) function which lets the user change effect
parameters in real time, using the FUNCTION switch. This makes it possible to adjust, for example,
overdrive, distortion, or reverb mix during a performance. It is also possible to control several parameters
simultaneously. The parameter(s) to be affected by RTM, the change distortion, and the change step
width can be set for each patch individually.
To use the RTM function, perform the following steps.
23 ●
If the module is off, press the Module Select key once more to turn it
on.
Which parameter can be controlled depends on the effect type. In the
"Effect Types and Parameters" table on page 36 - 45, the parameter
marked with "
←RTM" can be controlled by RTM.
For example, when the DELAY module is selected, parameter 5 (Mix
(←RTM) can be controlled by RTM.
BANK
FUNCTION
VALUE
ADVANCED GUITAR EFFECTS PROCESSOR
1.COMP
2.BOOSTER
3.OVERDRIVE
4.TALKING BOX
Sens/Gain
(Talking Gain)
Attack/Tone
(Talking Mode)
Level
(MIC Level)
VOLUME RTM
PRE DRIVE RTM
Gain/Top
Tone/Body
Level
ZNR
POSITION
MAIN DRIVE RTM
High/Depth
Midf/Rate/Sens
MidG/Reso
Low/Stage/Inv
Level
EQ RTM
Pitch/Key
Tone/Scale/Time
Shift/Mode/Dly
Bal/Mix
Amp Sim Mode
EFFECT1 RTM
Pitch/Key/Depth
Fine/Scale/Rate
Shift/Mode
Bal/Mix/Peak
SERI/PARA
EFFECT2 RTM
Time(x100mS)
Time(x1mS)
Feedback
Mix
SEAMLESS
DELAY RTM
Time
Tone/FB
Mix
Patch Level
FUNCTION Mode
REVERB RTM
1.OD
3.DIST
5.GRU
7.
METAL
1.3-BAND EQ
2.PHASE
3.PEDAL-WAH
4.AUTO-WAH
1.PITCH
3.DETUNE
4.PEDAL-PITCH
5.STRING
2.HPS 1.HALL1
3.ROOM 1
4.ROOM 2
5.PP-DELAY
2.HALL21.PITCH
3.CHO
5.TREM/PAN
6.RING MOD
1.NORMAL
2.ANALOG
3.HOLD
2.HPS
4.FLG
2.B-OD
4.FUZZ
6.LEAD
8.ACO
PRE DRIVE MAIN DRIVE EQ EFFECT 1 EFFECT 2 DELAY REVERB
TALKING BOX
POSITION SERI/PARA SEAMLESS
FUNCTION MODE BANK
(
VALUE
)
EDIT
(
CANCEL
)
GROUP STORE
1.MANUAL
2.BANK DOWN
3.DELAY(
TAP&HOLD)
4.BYPASS
5.MUTE
6.RTM
7.VOLUME
PRESETUSER
(BOTH) SEAMLESS
U
P
U O
1, 9
11, 12
3, 5, 7
3, 4, 6
2
VALUE
Time
2.HALL2
REVERB
EDIT
(
CANCEL
)
REVERB RTM
Adjusting Effect Parameters in Real Time (RTM)
STEP
1
Press the EDIT key to activate the Edit mode.
STEP
2
Use the Module Select keys to select the module to be controlled by RTM.
STEP
3
Use the Parameter Select keys to select parameter 1, operate the VALUE knob
and select the effect type.
STEP
4
Refer to the section "Effect Types and Parameters" and check the control target
parameter for the currently selected effect type. Then select this parameter with
the Parameter Select keys.
ADVANCED GUITAR EFFECTS PROCESSOR
Using the FUNCTION switch