Operation Manual

The EFFECT1 module LED flashes.
This is a global parameter that serves for turning the amp simulator on
or off and to select the mode.
• Amp Sim Mode is a global parameter whose setting does not
change when a different patch is selected. It can also be set
when the EFFECT1 module is off.
• If not stored, the setting reverts to the previous value when the
unit is turned off and then on again. When wishing to store the
setting, select any patch in the USER group and store it as
described on page 17.
The 3000 incorporates an amp simulator that can be used for all patches. The amp simulator will produce
realistic guitar amp sound also when monitoring with headphones or over an audio system.
● 28
Other Functions
Other Functions
Using the Amp Simulator
ADVANCED GUITAR EFFECTS PROCESSOR
BANK
FUNCTION
VALUE
ADVANCED GUITAR EFFECTS PROCESSOR
1.COMP
2.BOOSTER
3.OVERDRIVE
4.TALKING BOX
Sens/Gain
(Talking Gain)
Attack/Tone
(Talking Mode)
Level
(MIC Level)
VOLUME RTM
PRE DRIVE RTM
Gain/Top
Tone/Body
Level
ZNR
POSITION
MAIN DRIVE RTM
High/Depth
Midf/Rate/Sens
MidG/Reso
Low/Stage/Inv
Level
EQ RTM
Pitch/Key
Tone/Scale/Time
Shift/Mode/Dly
Bal/Mix
Amp Sim Mode
EFFECT1 RTM
Pitch/Key/Depth
Fine/Scale/Rate
Shift/Mode
Bal/Mix/Peak
SERI/PARA
EFFECT2 RTM
Time(x100mS)
Time(x1mS)
Feedback
Mix
SEAMLESS
DELAY RTM
Time
Tone/FB
Mix
Patch Level
FUNCTION Mode
REVERB RTM
1.OD
3.DIST
5.GRU
7.
METAL
1.3-BAND EQ
2.PHASE
3.PEDAL-WAH
4.AUTO-WAH
1.PITCH
3.DETUNE
4.PEDAL-PITCH
5.STRING
2.HPS 1.HALL1
3.ROOM 1
4.ROOM 2
5.PP-DELAY
2.HALL21.PITCH
3.CHO
5.TREM/PAN
6.RING MOD
1.NORMAL
2.ANALOG
3.HOLD
2.HPS
4.FLG
2.B-OD
4.FUZZ
6.LEAD
8.ACO
PRE DRIVE MAIN DRIVE EQ EFFECT 1 EFFECT 2 DELAY REVERB
TALKING BOX
POSITION SERI/PARA SEAMLESS
FUNCTION MODE BANK
(
VALUE
)
EDIT
(
CANCEL
)
GROUP STORE
1.MANUAL
2.BANK DOWN
3.DELAY(
TAP&HOLD)
4.BYPASS
5.MUTE
6.RTM
7.VOLUME
PRESETUSER
(BOTH) SEAMLESS
U
P
U O
1, 5
4
2
3
STEP
1
Press the EDIT key to activate the Edit mode.
STEP
2
Use the Module Select keys to select the EFFECT1 module.
STEP
3
Use the Parameter Select keys to select "Amp Sim Mode".
STEP
4
Use the VALUE knob to select the amp simulator mode as follows.
STEP
5
Press the EDIT key to revert to Play mode.
EDIT
(
CANCEL
)
EDIT
(
CANCEL
)
VALUE
Amp Sim Mode
EFFECT1 RTM
SS
TM
FUNCTION Mode
REVERB RTM
Values Control Assignment
oF OFF Amp simulator function is off.
C1– C9
COMBO
The amp simulator creates a sound resembling that of a combo amplifier of
about 100 watts. Higher values result in stronger box sound.
b1– b9
BRIGHT COMBO
The amp simulator creates a sound resembling that of a bright combo
amplifier of about 120 watts. Higher values result in stronger box sound.
S1– S9 STACK
The amp simulator creates a sound resembling that of a four-speaker
amplifier stack. Higher values result in stronger box sound.
NOTE