ATA Quick Start Guide

ManualsBrandsZoom ManualsNetwork Router5804

ATA Quick Start

ATA Quick StartATA Quick Start

ATA Quick Start

Your ATA comes with a power cube and Ethernet cable. Some

models also include other items, such as a phone cord, phone-jack

adapter, phone filter, or service provider flyer.

To complete the installation, you need the following:

- A broadband Internet connection using a cable modem,

ADSL, T1, E1, SDSL, or any other high-speed “always on”

Internet connection.

- An account set up with a VoIP service provider. If you

do not have an account set up, please look for a Read Me

First! flyer in the box for your VoIP ATA and follow its

instructions. If there is no flyer, go to your service provider’s

Web site and sign up for service.

- A router that uses your broadband Internet connection. This

can be an ADSL modem with a built-in router, a cable

modem with a built-in router, or some other router

connected to a broadband Internet connection. The router

needs at least one available LAN port, and the router needs

to be set up for 10/100 or 10/100/1000 or 10 Mbps. (Most

routers use 10/100 unless you change them.)

- A telephone so you can place and receive phone calls.

Now you’re ready to connect the ATA to a telephone, a router,

and a “live” power outlet. You will make your connections to the

back of the ATA.

Plug your telephone or cordless phone base station into the

ATA’s PHONE jack, which is on the far left of the ATA’s

back panel.

Note: In some countries outside the USA, you may need to use a phone-jack adapter.

Plug the adapter into the ATA’s PHONE jack and then plug in your phone

Plug one end of the Ethernet cable into the ATA’s Ethernet

port and the other end into a LAN port of your router.

If your unit has the word TELCO on the front panel of the

unit, continue with step 4.

If your unit does not have the word TELCO on the front

panel, continue with step 5.

For ATA units with a TELCO jack: Plug one end of the

supplied telephone cord into the ATA’s TELCO jack and

the other end into your home or office’s telephone jack, one

Summary of content (12 pages)

PAGE 1
ATA Quick Start Your ATA comes with a power cube and Ethernet cable. Some models also include other items, such as a phone cord, phone-jack adapter, phone filter, or service provider flyer. To complete the installation, you need the following: - A broadband Internet connection using a cable modem, ADSL, T1, E1, SDSL, or any other high-speed “always on” Internet connection. - An account set up with a VoIP service provider.
PAGE 2
where you would normally plug in a standard telephone. You may need to use a phone-jack adapter so the phone cord can fit into your wall jack. If you have ADSL service at that wall jack, you need to put an ADSL filter between that wall jack and the ATA’s TELCO jack. Now continue with step 5. 5 Plug the ATA’s power cube into the ATA’s PWR jack and the other end into a “live” power strip or wall outlet.
PAGE 3
If the ATA loses power or loses its Internet connection, you cannot place calls through the Internet. Advanced Features - Controlling the ATA from Your Phone Your ATA has a number of features that relate to calls traveling through the Internet. These features can be controlled from the phone plugged into your ATA as described below. For all these commands you first take the phone off-hook and then enter the command. *55 Enable call waiting on all calls. When a call is waiting, you will hear a tone.
PAGE 4
The commands above let you use a phone to directly control the ATA. Note that some VoIP service providers also let you control some of these features by using the setup screens for your account. Note also that these features apply only to VoIP calls, not calls that travel through the traditional phone network by way of your TELCO jack. Features for the traditional phone network are normally available from your traditional phone company. Resetting Your ATA You can reset your ATA by pressing the RESET switch.
PAGE 5
Inicio Rápido ATA Su ATA viene con un cargador (power cube) y un cable Ethernet. Algunos modelos también incluyen otros elementos, tales como un cordón telefónico, un adaptador para el enchufe telefónico (phone-jack adapter), un filtro telefónico, o un folleto del proveedor del servicio. Para completar la instalación se necesita lo siguiente: - Una conexión de Internet de banda ancha usando un cable modem, ADSL, T1, E1, SDSL, o cualquier otra conexión de Internet de alta velocidad “siempre funcionando”.
PAGE 6
3 Si su unidad tiene la palabra TELCO en el panel frontal de la unidad, continuar con el paso 4. Si su unidad no tiene la palabra TELCO en el panel frontal continuar con el paso 5. 4 Para las unidades ATA con un enchufe TELCO: Conectar un extremo del cordón telefónico recibido en el enchufe TELCO del ATA y el otro extremo en el enchufe telefónico de su casa u oficina, donde por lo general usted conecta un teléfono estándar.
PAGE 7
- Si lo tiene: Usted puede hacer llamadas que viajan primero a través de Internet, o puede hacer llamadas que viajan primero a través de su servicio normal de teléfono mediante su enchufe TELCO. Su ATA puede ser determinado por su proveedor de servicio, por ejemplo, para que enrute todas las llamadas a través de Internet a menos que esas llamadas sean locales o llamadas de emergencia.
PAGE 8
*73 Deshabilitar el paso de llamadas. *82 Habilitar el identificador de llamadas para todas las llamadas que salgan. *62 Bloquear el identificador de llamadas para todas las llamadas que salgan. *65 Habilitar el identificador de llamadas para todas las llamadas que entran. *85 Deshabilitar el identificador de llamadas para todas las llamadas que entran. *67 Habilitar el identificador de llamadas para la próxima llamada que salga.
PAGE 9
configuraciones de su ATA se regresarán a las últimas suministradas por su proveedor de servicio. Si usted presiona RESET por un tiempo mucho más corto el ATA lo reseteara tal y como si lo hubiera apagado y luego vuelto a encender. Como Registrar su Producto y Como Conseguir Ayuda Si necesita ayuda, deberá ponerse en contacto con su proveedor del servicio. Lo animamos a registrar su producto y tener en cuenta las muchas opciones disponibles por parte de Zoom. - Por favor ir a www.zoom.
PAGE 10
afterwards. In the event such a disconnection is deemed necessary, you will be advised of your right to file a complaint with the FCC. From time to time, the telephone company may make changes in its facilities, equipment, or operations which could affect the operation of this equipment. If this occurs, the telephone company is required to provide you with advance notice so you can make the modifications necessary to obtain uninterrupted service.
PAGE 11
Industry Canada Emissions Statement This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Electrostatic Discharge Statement The unit may require resetting after a severe electrostatic discharge event. Safety Notices CAUTION: To reduce the risk of fire, use only No.
PAGE 12
NOTICE This document contains proprietary information protected by copyright, and this Quick Start and any accompanying hardware, software, firmware, and documentation are copyrighted. No part of this document may be photocopied or reproduced by mechanical, electronic, or other means in any form.