User's Manual

34
Effect Types and Parameters
Effect Types and Parameters
006 Limiter This is a limiter that suppresses signal peaks above a certain reference level.
Knob1 Knob2 Knob3
Page01
THRSH 0–50 P Ratio 1–10 Level 0–150
Adjusts the reference signal level for
the limiter action.
Adjusts the compression ratio of the
limiter.
Adjusts the output level.
Page02
REL 1–10
Adjusts the delay between the point
where the signal level falls below the
threshold level and the limiter release.
007 SlowATTCK
This effect slows the attack of each note, resulting in a violin-like performance.
Knob1 Knob2 Knob3
Page01
Time 1–50 P Curve 0–10 Level 0–150
Adjusts the attack time.
Set the curve of volume change during
attack.
Adjusts the output level.
008 ZNR ZOOM'suniquenoisereductioncutsnoiseduringpausesinplayingwithoutaffectingthetone.
Knob1 Knob2 Knob3
Page01
THRSH 1–25 P DETCT GtrIn, EfxIn Level 0–150
Adjusts the effect sensitivity. Sets control signal detected. Adjusts the output level.
009
GraphicEQ This unit has a seven band equalizer.
Knob1 Knob2 Knob3
Page01
50Hz -12–12 120Hz -12–12 400Hz -12–12
Adjusts the amount of boost/cut at 50
Hz.
Adjusts the amount of boost/cut at
120 Hz.
Adjusts the amount of boost/cut at
400 Hz.
Page02
500Hz -12–12 800Hz -12–12 4.5kHz -12–12
Adjusts the amount of boost/cut at
500 Hz.
Adjusts the amount of boost/cut at
800 Hz.
Adjusts the amount of boost/cut at
4.5 kHz
Page03
10kHz -12–12 Level 0–150
Adjusts the amount of boost/cut at
10 kHz.
Adjusts the output level.
010 ParaEQ This is a 2-band parametric equalizer.
Knob1 Knob2 Knob3
Page01
Freq1 20Hz–20kHz Q1
0.5, 1, 2, 4, 8, 16 Gain1 -20–20
Adjusts center frequency of EQ1. Adjusts EQ1 Q. Adjusts EQ1 gain.
Page02
Freq2 20Hz–20kHz Q2
0.5, 1, 2, 4, 8, 16 Gain2 -20–20
Adjusts center frequency of EQ2. Adjusts EQ2 Q. Adjusts EQ2 gain.
Page03
Level 0–150
Adjusts the output level.
011 Splitter
This effect divides the signal into two bands (high/low) and lets you freely adjust the mix
ratio of the two bands.
Knob1 Knob2 Knob3
Page01
Hi 0–100 Lo 0–100
Freq 80Hz–2.5kHz
Adjusts the mix ratio of the high
frequency band.
Adjusts the mix ratio of the low
frequency band.
Adjusts the crossover point between the
high frequency and low frequency band.
Page02
Level 0–150 P
Adjusts the output level.
012 Bottom B Emphasizes the low and high frequencies.
Knob1 Knob2 Knob3
Page01
Bass 0–10 P Trebl 0–10 Level 0–150
Adjusts the amount of low-frequency
boost.
Adjusts the amount of high-frequency
boost.
Adjusts the output level.
013 Exciter This exciter is in the style of the BBE Sonic Maximizer.
Knob1 Knob2 Knob3
Page01
Bass 0–10 P Trebl 0–10 Level 0–150
Adjusts the amount of low-frequency
phase correction.
Adjusts the amount of high-frequency
phase correction.
Adjusts the output level.