Handy Video Recorder Q2n --=M---11=-- ~!~ 2COM Handy Video Recorder Operation Manual You must read the Usage and Safety Precautions before use. This document cannot be displayed properly on black-and-white displays. © 2018 ZOOM CORPORATION Copying or reprinting this manual in part or in whole without permission is prohibited.
Operation Manual overview You might need this manual in the future. Always keep it in a place where you can access it easily. The contents of this document and the specifications of the product could be changed without notice. • iOS is a trademark or registered trademark of Cisco Systems, Inc. (USA). • HDMI (High-Definition Multimedia Interface) is a trademark of HDMI Licensing, LLC.
Introduction Thank you very much for purchasing a ZOOM The Q2n-4K Handy Video Recorder (hereafter, “ Q2n-4K ”). Q2n-4K has the following features. Capture the immediacy of live performances in both audio and video Using the wide angle lens, you can record video even when close to the subject. With the XY format condenser mic that has excellent sound pressure resistance, you can record even clearer stereo images at high resolutions up to 24-bit/96 kHz.
Contents Introduction .................................................................................................................................................. 3 Contents ........................................................................................................................................................ 4 Names of parts ............................................................................................................................................. 6 Preparations .....
Using as a web camera ......................................................................................................................... 38 Compensating for lags between video and audio............................................................................ 38 Using as a card reader ........................................................................................................................... 39 Using as a USB mic .......................................................................
Names of parts ■ Front G) Built-in XY mic @ Lens @ REC LED Handy Video Recorder G) Built-in XY mic The two crossing directional mics can record a three-dimensional sound with natural depth and width. @ Lens This lens has an F2.8 brightness and 150° wide angle. @ REC LED This LED shows the recording status. It lights red during recording.
■ Back Display (LCD) @ Function buttons Function buttons ® SETTING/EXIT button @ POWER/PLAY button @ REC button G) Display (LCD) This shows the video and various types of information. @ Function buttons Use these to operate the functions shown on the display. @ POWER/PLAY button Use this to turn the power ON/OFF and to start video playback. @ REC button Use this to start and stop recording. Use this to confirm on setting and confirmation screens.
■ Sides Input volume G) Output volume USB port @ Headphone jack @ External input jack 0 Micro HDMI connector Strap hole G) Output volume control Use to adjust the output volume. @ Headphone jack This outputs sound to headphones or a connected device. @ External input jack Use this to input sound from a connected device. @ Input volume dial Use to adjust the recording level. ® USB port Connect this to a computer or iOS device to use as a web camera, card reader or USB mic.
■ Bottom Battery/SD card compartment cover @ Tripod mounting threads IRlil□rt;OO@ ~IID ~rnllID mi MffllllW □lrll~□ IID~ Mlr111!1W:OOH(UW)/ aM(11!iWI/FOOll11!iWI .. -~m•z ~i1'!'ll[fflj]i•o!iml'l",~6•D........., 0 0 G) Battery/SD card compartment cover Remove when installing batteries and microSD cards. @ Tripod mounting threads Use these screw threads to attach a tripod (not included).
Preparations Supplying power Using batteries 1. Open the battery/card compartment cover. 2. Install the batteries. AA batteries 3. Close the battery/card compartment cover. NOTE After installing batteries, set the correct battery type.
Using an AC adapter 1. Connect the cable of an AD-17 AC adapter to the USB port. I~= • tf•~ I 2. Plug the AC adapter into an outlet. HINT When connected to a computer, power can be supplied by USB.
Inserting microSD cards 1. Open the battery/card compartment cover. 2. Insert the microSD card into the card slot. microSD card To remove a microSD card, push it further into the slot and then pull it out. 3. Close the battery/card compartment cover. NOTE • Always make certain that the power is off when inserting or removing a microSD card. Inserting or removing a card while the power is on could result in data loss.
Turning the power on/off Turning the power on 1. Press and hold . After startup completes, the REC LED on the front will light green and the Recording Screen will appear on the display. HINT To turn the power off, keep pressing until "Goodbye See You!” appears on the display.
Setting up when first turned on The first time the Q2n-4K is turned on, the display language and the date and time must be set. HINT Language display and date and time settings can be changed later on the Setting Screen. ( language shown” on page 52, “Setting the date and time” on page 47) ➔ Setting the language shown 1. Use < and > to select the language displayed. VIDEO LO CUT [□ □] FOV AUDIO SCENE AUTO GAIN [□ □] EXIT 2. Press [I• I) to confirm.
Setting the date and time 1. Press the button for the item to be set. VIDEO LO CUT [□ □] FOV AUDIO SCENE AUTO GAIN EXIT 2. Press [I• I] to confirm.
Recording Recording Screen overview The Recording Screen opens when the power is turned on. When recording: recording time In recording standby: available recording time Remaining battery charge VIDEO setting LO CUT setting AUDIO setting FOV setting AUTO GAIN setting SCENE setting Level meters Peak indicators HINT If the power is turned on when connected to a computer, the USB function selection screen will open.
Making video recording settings Use the buttons on both sides of the display to change settings. Video quality Low-frequency noise reduction Field of view Audio quality Scene Setting the video quality The video quality (resolution) and frame rate per second can be set. 1. Press VIDEO on the Recording Screen to set the video quality.
Setting the field of view This sets the field of view (FOV) for videos. 1. Press FOV on the Recording Screen to set the field of view. VIDEO LO CUT [□ [□ [□ FOV AUDIO SCENE AUTO GAIN □] EXIT Setting Explanation Distortion correction WIDE This widens the field of view. — · ; I\ ✓ 0 · TELE ✓ ✓ '/ This narrows the field of view.
Setting the scene type This sets the camera settings for the recording conditions (scene). 1. Press SCENE on the Recording Screen to set the scene type. VIDEO LO CUT □] [□ FOV AUDIO [□ SCENE AUTO GAIN [□ [ ► l] [I • I] [ x l] EXIT o Setting Explanation AUTO Settings change according to the recording conditions. OUTDOOR Settings are optimized for outdoor recording. SUNSET Settings are optimized for sunset scenes. NIGHT Adjustments are made for night and other dark situations.
Setting low-frequency noise reduction The low-cut filter can be set to reduce the sound of wind, vocal pops and other noise. 1. Press LO CUT on the Recording Screen to set the low-frequency noise reduction. 1■ 1 ul VIDEO LO CUT □] FOV AUDIO □] [□ SCENE AUTO GAIN □] [□ EXIT Setting Explanation OFF Low-frequency noise reduction is disabled. 80 Hz These set the cutoff frequency.
Adjusting recording levels Adjusting levels manually 1. Turn to adjust the recording level. Low High Adjust so that the level meters are around −12 dB with the loudest sounds. Level meters Peak indicators NOTE • The peak indicators light and the REC LED on the front blinks when loud sounds are input. • Recording when the indicators are lit could cause the sound to become distorted. Lower the input volume to avoid this.
Using automatic level adjustment The recording level can be adjusted automatically according to the use conditions. 1. Press AUTO GAIN on the Recording Screen to set the automatic gain adjustment. VIDEO LO CUT □] [□ FOV AUDIO □] [□ SCENE AUTO GAIN EXIT Setting Explanation OFF This disables automatic level adjustment. Adjust the recording level manually. CONCERT This is suitable for recording band performances, concerts and other loud situations.
Recording ■ Recording video 1. Press [I• I] . VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT This starts video recording. 2. Press [I• I] again to stop video recording. NOTE • The energy saving function will make the screen dim during recording. (➔ ----“Setting the display backlight time” on page 43) • During video recording, the REC LED on the front lights red.
Connecting external input devices You can capture audio with an external mic or audio device when recording video or audio. 1. Connect the external mic or audio device to the external input jack. EXT IN NOTE The built-in mics are disabled when an external device is connected to the external input jack. HINT • This jack can provide plug-in power to mics that use it.
Playing recordings Playback Screen overview From the Recording Screen, press to open the Playback Screen.
Playing recordings 1. Press on the Recording Screen. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] I(!) [I ► ll111 • I] [I X 0 ~ EXIT Playback of the last recorded file or the most recently played file will start. NOTE • The 2. Press Q2n-4K can only play videos that it recorded. to stop playback and reopen the Recording Screen.
Playback operations The following operations are possible during playback. Changing the playback position Pause/resume Press Search forward Press and hold Search backward Press and hold Selecting files Move to next file Press Move to previous file Press Playing files continuously Playback can be set so that after playback of one file completes the next file can be played back without stopping.
Adjusting the output volume 1. Use to adjust the volume. Qo OEXTIN C=::J VIDEO LO CUT □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT HINT • The volume can be adjusted separately for the speaker and headphones. • The volume can be set from 0 to 30.
Headphone/line output You can listen to the audio with headphones or an external audio amplifier. 1. Connect headphones or audio equipment to the headphone jack using a stereo mini plug cable. HINT When the Recording Screen is open, you can monitor the input sound.
Viewing on an HDMI-compatible TV Use an HDMI cable to connect with an HDMI-compatible TV to view Q2n-4K video recordings on it. 1. Connect an HDMI cable (not included) to the Micro HDMI connector. D - - 2. Press I ----:::::i -i:::::-- --- to play the video and audio. VIDEO LO CUT [□ □] FOV AUDIO C] [C SCENE AUTO GAIN [□ □] I(!) [I ► 11 1[1 • 0 I] [I X I] EXIT The display on the recorder will turn off and the recorded file will play on the TV screen.
Managing files Checking file information You can view a variety of information about the current playback file. 1. Press on the Playback Screen. VIDEO LO CUT FOV AUDIO [□ [□ [Q] SCENE AUTO GAIN □] EXIT This shows information about the current playback file. Information about the duration, size, date, time, video and audio can be checked. 2. Press . This reopens the Playback Screen.
Deleting files You can delete files that you do not need. 1. Press on the Playback Screen. VIDEO LO CUT [Q] FOV AUDIO [□ [□ ij;J] SCENE AUTO GAIN □] EXIT The deletion screen will open. 2. Press to select a file. le VIDEO LO CUT 111 1 FOV AUDIO [□ [□ □] SCENE AUTO GAIN □] EXIT A check will appear in the box at the top left of the file image. HINT You can use < and > to change files and add checks to multiple files. 3. Press .
4. Press II• I) to select Yes • . VIDEO LO CUT □] FOV AUDIO [□ [□ □] SCENE AUTO GAIN □] EXIT The checked files will be deleted. To cancel deletion, press to select No ×.
Using USB functions Connecting to computers and iOS devices Use a USB cable to connect to a computer or iOS device and use the recorder as a web camera, card reader or USB mic. 1. Press on the Recording Screen. VIDEO LO CUT [□ □] FOV □ AUDIO ] c..-..i:~•••"""' [ SCENE AUTO GAIN □ ]-=~..~ =-Q) [[ ► l] □ [□ cr::1mo I EXIT This opens the Setting Screen. 2. Press . ➔ VIDEO LO CUT [□ □] FOV AUDIO □] SCENE AUTO GAIN □] Q> [[ ► l] [[ • This opens the USB Connection Setting Screen.
3. Press the button for the function to be used. VIDEO LO CUT [□ FOV AUDIO IQ] [□ SCENE AUTO GAIN IQ] [□ <.
on any function screen. 6. To end use, press 7. Press II• I on the Confirmation Screen to select Yes This reopens the Recording Screen. • . NOTE • When connected to a computer, power can be supplied by USB. • When connected to an iOS device, use batteries because power cannot be supplied by USB. • A list of iOS devices that have been confirmed to work with this unit can be checked at www.zoom. co.jp.
Turning the power on when connected to a computer If the Q2n-4K power is turned on when connected to a computer, the USB function selection screen will open. 1. Use < and > to select the function to use. VIDEO LO CUT FOV AUDIO SCENE AUTO GAIN [□ □] EXIT 2. Press II• I) to confirm. VIDEO □] FOV □] < SCENE LO CUT [□ >[□ [□ u~;E: D □] AUDIO DI AUTO GAIN IJJEBCHM ;< EXIT :EtHEli EXIT 3. Press [I• I) on the Confirmation Screen to select Yes This activates the selected mode.
Using as a web camera The Q2n-4K can be used as a web camera to input audio and video to a computer. 1. Connect the Q2n-4K with a computer. “Connecting to computers andiOSdevices” on page34) (➔ -----NOTE Web camera use is not possible with an iOS device. 2. Launch an application that uses a camera on the computer, and select the Q2n-4K . NOTE • The recorder can simultaneously transmit video and audio with resolutions up to 720 p HD and 48 kHz/16-bit to a computer.
Using as a card reader The Q2n-4K can be used as a card reader to read and write data from computers and iOS devices. 1. Connect the Q2n-4K to a computer or iOS device. “Connecting to computers and iOS devices” on page 34) (➔ ---------------- 2. Open a file management screen on the computer or iOS device and show the contents of the microSD card in the Q2n-4K . 3. Work with the files on the microSD card. 4.
Using as a USB mic The Q2n-4K can be used as a USB mic to input audio to a computer or iOS device. 1. Connect the Q2n-4K to a computer or iOS device. “Connecting to computers andiOSdevices” on page34) (➔ ------ 2. Launch an application that uses a mic on the computer or iOS device, and select the Q2n-4K . HINT Refer to the manual for the application that you are using for the procedures to select the Q2n-4K . 3.
Battery settings Setting the type of battery used Set the type of battery used so that the amount of remaining battery charge can be accurately displayed. 1. Press on the Recording Screen. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT This opens the Setting Screen. 2. Press ➔ three times to change the Setting Screen. VIDEO □] FOV □] SCENE □] NTSC/PAL 'ff I ; Plug-in Power 1; lltt SD E,1eep ◄) Fonn::lt .·. [□ AUDIO [□ AUTO GAIN Ill PIa:/ Mode ~' I LO CUT I·".
3. Press Battery Type to set the type of battery used. VIDEO LO CUT Batten·· T~/Pe - - 'I 11 I I' f FOV [□ [□ [□ AUDIO □] SCENE AUTO GAIN □] EXIT The options are Alkaline, Ni-MH and Lithium. 4. Press . This reopens the Recording Screen.
Enabling energy saving Setting the display backlight time Power can be saved by shortening the amount of time that the backlight stays lit. 1. Press on the Recording Screen. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT This opens the Setting Screen. 2. Press ➔ three times to change the Setting Screen.
3. Press Power Save, and set the time until the backlight dims. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO Po 1.i.ie r :::a•. .•e --1 II I' SCENE AUTO GAIN □] EXIT Setting Explanation Off The backlight always stays bright. 1 min The backlight dims if no operation occurs for 1 minute. 3 min The backlight dims if no operation occurs for 3 minutes. 5 min The backlight dims if no operation occurs for 5 minutes. 4. Press . This reopens the Recording Screen.
Setting the Auto Power Off function Set to turn off automatically if not used at all for a set amount of time when running on battery power. NOTE This function is disabled during recording and playback as well as when it is powered through its USB port. 1. Press on the Recording Screen. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT This opens the Setting Screen. 2. Press ➔ three times to change the Setting Screen. VIDEO LO CUT [□ □] FOV AUDIO □] SCENE AUTO GAIN □]
3. Press Auto Power Off, and set the time until the power turns off. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN t-\uto Power· Off - - - . ii II (!) ([ ► l) [I e I] ([ X ll EXIT O Setting Explanation Off The Auto Power Off function is disabled. 1 min The power will turn off automatically 1 minute after the last operation. 3 min The power will turn off automatically 3 minutes after the last operation.
Setting the date and time If the date and time are set, the recorder can add the recording date and time to files. 1. Press on the Recording Screen. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT This opens the Setting Screen. 2. Press ➔ two times to change the Setting Screen. VIDEO LO CUT [□ □] FOV AUDIO □] SCENE AUTO GAIN [OJ] [ ► l] [I • I] [ x l] EXIT o This opens the Date and Time Setting Screen. 3. Press the button for the item to be set.
Setting the volume of the operation sound Set the volume of the 1. Press Q2n-4K operation sound. on the Recording Screen. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT This opens the Setting Screen. 2. Press Beep, and set the volume. VIDEO LO CUT [□ [□ [□ FOV AUDIO SCENE AUTO GAIN □] EXIT Setting Explanation ◄x ◄> No operation sound is output. ◄ >)) A high-volume operation sound is output. 3. Press A low-volume operation sound is output. .
Enabling continuous playback Playback can be set so that after playback of one file completes the next file can be played back without stopping. 1. Press on the Recording Screen. VIDEO LO CUT [□ [□ [□ C] FOV AUDIO □] SCENE AUTO GAIN EXIT This opens the Setting Screen. 2. Press Play Mode, and set whether continuous playback is enabled. VIDEO NTSC/PAL □] W ,_, ;11: ~ _ FOV □] SCENE I • • 1 AUDIO Beep Fonnat -,111) AUTO GAIN P .
Using mics that support plug-in power Enable plug-in power from the 1. Press Q2n-4K for mics that support it. on the Recording Screen. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT This opens the Setting Screen. 2. Press Plug-in Power and set it to On. VIDEO □] PIu•~1- in Power· - LO CUT Wt FOV AUDIO [□ [□ □] SCENE AUTO GAIN □] EXIT 3. Press . This reopens the Recording Screen.
Setting the standard frame rate This sets the standard recording frame rate used according to the regional video format. 1. Press on the Recording Screen. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT This opens the Setting Screen. 2. Press NTSC/PAL to set the standard frame rate.
Setting the language shown Set the language shown on the display. 1. Press on the Recording Screen. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT This opens the Setting Screen. 2. Press ➔ three times to change the Setting Screen. VIDEO □] FOV □] SCENE □] NTSC/PAL 'j.' I 1 : ~I Plug-in Power , , 1 • Beep • SD Format ◄> LO CUT [□ AUDIO AUTO GAIN Play Mode c., [ ► l) [I • I] [ x l) EXIT o 3. Press Language.
Formatting microSD cards To maximize the performance of a microSD card, use the 1. Press Q2n-4K to format it. on the Recording Screen. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT This opens the Setting Screen. 2. Press SD Format. VIDEO LO CUT [□ C] FOV ::;[1 □] AUDIO Forn1.:1 t SCENE AUTO GAIN [□ □] EXIT This opens a formatting confirmation screen. 3. Press II• I to select Yes e. This will start microSD card formatting.
Restoring factory default settings You can restore all 1. Press Q2n-4K settings to their factory defaults. on the Recording Screen. VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT This opens the Setting Screen. 2. Press ➔ three times to change the Setting Screen. VIDEO Plug-in Power □] NTSC/PAL r,. ; i~ ~, - , I FOV □] SCENE □] Beep SD L [□ AUDIO Fo · - ◄) PI a:,.. LO CUT AUTO GAIN -+ Ill Mode 11 I-,-,,-, t!> [ ► l] [I • I] [ x l] EXIT o 3.
4. Press II• I) to select Yes • . VIDEO LO CUT [□ [□ [□ □] FOV AUDIO □] SCENE AUTO GAIN □] EXIT This starts resetting the Q2n-4K . After resetting completes, the power will automatically turn off.
Updating the firmware The Q2n-4K firmware can be updated to the latest versions. 1. Install new batteries in the Q2n-4K or connect an AC adapter. NOTE Executing a firmware update is not possible if the remaining battery power is low. 2. Copy the firmware update file to the root directory on a microSD card. The latest firmware update file can be downloaded from www.zoom.co.jp. 3. Insert the microSD card into the microSD card slot. to turn the power on. 4.
6. Press II• I) to select Yes • . After updating completes, a notification screen appears. NOTE Do not turn the power off during a firmware update. 7. Press and hold to turn the power off.
Responding to warning messages If one of the warning messages below appears, follow the instructions to respond to it. ■ Warning messages that appear during startup Message A Explanation and response [I,:it8 and Ti 1118 · '.'.'8 r-e P8•:,8t A The date and time setting were initialized. Reset the time. (➔ “Setting the --date and time” on page 15) Data recording was not completed properly, so the unit tried to recover it but recovery failed. Fi le recoveryfai led.
Troubleshooting If you think that the Q2n-4K is operating strangely, check the following items first. Recording/playback trouble ■ It becomes warm • The unit and the microSD card might become warm but this is not a malfunction. ■ There is no sound or it is very quiet • Check the connections with connected devices and their volume settings. • Confirm that the output volume is not set low. ■ Recorded sound cannot be heard or is very quiet • Check the recording level setting.
Specifications Image sensor 1/2.3" 16 M-pixel CMOS sensor Lens F 2.8, 150° FOV Video format MPEG-4 AVC/H.264 (MOV) Video resolutions 4K: 30 p, 25 p, 24 p 1080: 60 p, 50 p, 30 p, 25 p, 24 p 720: 30 p, 25 p Audio formats WAV: 96 kHz/24-bit, 48 kHz/24-bit, 44.1 kHz/16-bit Audio functions · LO CUT: OFF, 80 Hz, 120 Hz, 160 Hz · AUTO GAIN: OFF, CONCERT, SOLO, MEETING · DELAY: 0.0 F, 0.5 F–10.
ZOOM CORPORATION 4-4-3 Kanda-surugadai, Chiyoda-ku, Tokyo 101-0062 Japan www.zoom.co.
2n-4K Handy Video Recorder Q2n Ea 2c::::x::JM Handy Video Recorder Quick Guide You must read the Usage and Safety Precautions before use. I■ The Operation Manual can be downloaded from the ZOOM website (https://www.zoom.jp/docs/ q2n-4k). This page has files in PDF and ePub formats. The PDF file format is suitable for printing on paper and reading on a computer. The ePub format can be read with electronic document readers and is designed for reading on smartphones and tablets.
Preparations 1. Remove the battery/SD card compartment cover and install batteries and a microSD card. microSD card 2. Press I I l 3. -----------------------------------, HINT • The dedicated AC adapter (ZOOM AD-17) can also be connected to the USB port to use AC power. • When connected to a computer, power can be supplied by USB. I ► 1 to turn the power on. -----------------, I II HINT Press and hold (!) off. ► to turn the power I 2 I J Set the language shown.
Recording ■ Using the Recording Screen The Recording Screen opens when the power is turned on. When recording: recording time In recording standby: available recording time Remaining battery charge VIDEO setting LO CUT setting FOV setting AUDIO setting SCENE setting AUTO GAIN setting Start recording Stop recording (press when recording) ■ Making video recording settings VIDEO • Setting video quality: Press l-~W) This sets the video resolution and frame rate per second.
■ Adjusting the audio recording level • Adjusting manually: Turn Adjust so that the level meters are around −12 dB with the loudest sounds. • Adjusting automatically: Turn AUTO GAIN Setting Explanation OFF This disables automatic level adjustment. Adjust the recording level manually. CONCERT Use for recording band performances, concerts and other loud situations. SOLO Use for solo performances and other quiet sounds. MEETING Use for meetings and field recordings. HINT - ------ f~\I Low High
Playing recordings ■ Playing back videos 1. Press Status indicator Playing : Paused : Stopped : on the Recording Screen. Remaining playback time Remaining battery charge The recorded file will start playing. 2. Press to stop playback and re- open the Recording Screen. 1 2 ■ Playback operations Function Operation Pause/resume Press <.'.
Setting item list From the Recording Screen, press to open the Setting Screen where you can use the following functions and settings. ■ Page 1 Item Explanation NTSC/PAL This sets the standard recording frame rate used according to the regional video format. [NTSC (30 FPS)/PAL (25 FPS)] Beep Set the volume of the sound made when turned on or operated. [ ◄ x / ◄ > / ◄ >)) ] Play Mode Set whether files are played continuously or playback stops after one file.
Connecting by USB 1. When the Recording Screen is open, press 3 3 ~ ~ to open the Setting Screen. CARD READER --- 2. Press ➔ to open the USB Connection Setting -t CARD READER for 10S o e oo 4 . ~ ,. ~ Screen. 3. 4. 5. 6. USB MIC ~ ~j EI]2 ., lie· . . F.,1,6 Pf --- . --- Press the button for the function to use. Press II• 1 on the Confirmation Screen to select “Yes Use a USB cable to connect a computer or iOS device. To end a USB connection, press • ”. on any function screen.
2COM® ZOOM CORPORATION 4-4-3 Kanda-surugadai, Chiyoda-ku, Tokyo 101-0062 Japan http://www.zoom.co.
Included items The package should contain the following items. Please confirm that they have all been included. Q2n-4K --- fl'- □ - Qui c k Guid e I ■ ==-~---~- I ~---. . ----=--·-. . --_ ___ __ .. __ _ -·----------·..., .., _., - ~==:... .· :.: : :.: :-·--..
. . c2 1 .....,:____1M®• Optional accessories Accessory for the Q2n-4K Handy Video Recorder Universal Windscreen Tripod to three-prong action camera mount adapter WSU-1 .. ACM-1 '. The SCU-20 is a pad9ed-shell case which protects your Q2n-4K from shock and scratches for storing each accessory.
Q2n-4K Handy Video Recorder About recommended batteries To extend continuous shooting time, following batteries are recommended. ■ Alkaline LR6 (1.5 V) • Panasonic EVOLTA • FUJITSU High Power • SONY STAMINA • Energizer MAX • Other suitable batteries for "digital cameras" and "charging smartphones" that can supply large current continuously. ■ ■ Nickel Metal Hydride HR6 (1.2 V) • Panasonic eneloop • Panasonic eneloop pro • Energizer Recharge (2000 mAh) • Duracell Rechargeable (1.
2COM I Disposal of Old Electrical & Electronic Equipment (Applicable In __________._ European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it will be handed over at a designated collection point for the recycling of electrical and electronic equipment.
Q2n-4K Operation Confirmed micro SDHC/SDXC Cards As of November 2018, the operation confirmed micro SDHC/SDXC Memory Cards are as follows.
Safety and Usage Precautions Précautions de sécurité et d’emploi Sicherheits- und Gebrauchshinweise Precauzioni d'uso e sicurezza Precauciones de uso y seguridad 安全上の注意／使用上の注意 安全使用设备／注意事项 © 2018 ZOOM CORPORATION
2COM®Safety Precautions Read the content of these Usage and Safety Precautions carefully before use, and then use the product correctly. In this document, symbols are used to show precautions for the prevention of injury and loss to you or other people that could result from misuse. The meanings of these symbols are as follows.
■ Battery handling (for products that use batteries) 0 0 0 0 0 Install batteries with the correct +/− orientations. Use the specified batteries. Do not use new and old batteries together. Do not use batteries of different brands or types together. Remove the batteries when the unit will not be used for a long time. Always turn the power OFF for all equipment before connecting any cables. NOTE: Contact our company service department if a leak should occur.
2• = •M~ NORTH AM ERI C A WARRANTY REGISTRATION Zoom products are distributed in the United States by Zoom North America. Please visit warranty.zoom-na.com -or- return this card within 10 days of purchase to register your product. CUSTOMER INFORMATION: WHERE 010 YOU BUY THIS PRODUCT?: NAME: ADDRESS: CITY: DATE OF PURCHASE: I STATE: 12P. HOW 0 0 YOU INTEND ON USING THIS ZOOM PRODUCT?: EMAIL: PRODUCT INFORMATION: MODEL: SERIAL NUMBER: - --- - - - - - - - --- - - - - -- - --- - - .
PLACE STAMP HERE 2 l_w: .. . .__IM.
Importers in EU countries UNITED KINGDOM SPAIN/ PORTUGAL Zoom UK Distribution Ltd tla Zoom UK Adagio, S.L.U. 15 Weston Barns, Hitchin Road, Weston, Hertfordshire, SG4 7AX, United Kingdom Tel: (44) 1462-791100 E-mail: info@zoomcorp.co.uk I enquiries@zoomcorp.co.uk Avenida de La Ferreria n° 3-5 Polfgono Industrial La Ferreria 08110 MONTCADA I REIXAC, Barcelona, Spain Tel: (34) 93-564-60-12 E-mail: comercial@adagio.es http://www.adagio.
