UIB-01 Installation Manual © Zoom Corporation Reproduction of this manual, in whole or in part, by any means, is prohibited.
Safety Precautions Disregarding instructions printed here incurs the risk of death or Warning severe injury to persons. Disregarding instructions printed here incurs the risk of injury to Caution persons and/or damage to peripheral equipment. Please observe the following safety tips and precautions to ensure hazard-free use of the UIB-01. ■ Handling ● Before installing the UIB-01 in the Warning MRS-1044, be sure to turn the MRS1044 off and disconnect the AC adapter from the outlet.
Introduction Thank you for selecting the ZOOM USB Interface Board UIB-01 (hereafter called the "UIB-01"). To ensure correct use of this product, please read and follow all instructions contained in this manual. About the UIB-01 ● Project backup/restore You can copy any project of the MRS-1044 to the hard disk of the computer. This is convenient for creating backups of important projects. A backed-up project can be restored to the MRS-1044 at any time.
Preparations This section describes how to install the UIB-01 in the MRS-1044, and how to install the driver software on the computer. These steps are required before the UIB-01 can be used. 2. Installing the UIB-01 The UIB-01 is designed for installation in the side panel slot of the MRS1044. 1. Correct Remove the two screws that fasten the cover of the side panel slot, and remove the cover. These screws will be used to fasten the UIB-01. Incorrect 3.
Connection between computer and MRS-1044 1. Turn power to the computer on and start Windows 98/Me/2000. 2. Insert the CD-ROM supplied with the UIB-01 into the CDROM drive of the computer. 3. To allow the computer to recognize the MRS-1044 properly, a driver must be installed. The steps for installing the driver differ for the various operating systems. Please refer to the appropriate page, as shown below. Windows 98 → this page / Windows Me → p.13 / Windows 2000 → p.15 Windows 98 driver installation 1.
3. 10 5. After a while, the following screen will be shown. Click on the [Finish] button. 6. After a while, the following screen will be shown. Click on the [Next] button. 7. Place a check mark in "Search for the best driver..." on the next screen, and click on the [Next] button (same as step 2). 8. Place a check mark in "Specify a location " on the next screen, enter "[CD-ROM drive letter]:\", and click on the [Next] button (same as step 3). Preparations Preparations 4.
9. Verify that the following indication is shown, and click on the [Next] button. Windows Me driver installation 1. Verify that the following indication is shown on the computer display. Then place a check mark in "Automatic search for ...", and click on the [Next] button. Preparations Preparations 10. After a while, the following screen will be shown. Click on the [Finish] button. * If the indication is not shown → p.31 2. After a while, the following screen will be shown.
3. Windows 2000 driver installation 1. Verify that the following indication is shown on the computer screen, and click on the [Next] button. Preparations Preparations 4. After a while, the following screen will be shown. Place a check mark in "Automatic search for...", and click on the [Next] button. After a while, the following screen will be shown. Click on the [Finish] button. * If the indication is not shown → p.31 2. On the next screen, place a check mark in "Search for a suitable driver...
On the next screen, place a check mark in "Specify a location", and click on the [Next] button. 5. Verify that the following indication is shown, and click on the [Next] button. 4. Enter "[CD-ROM drive letter]:\", and click on the [OK] button. The following example uses the drive letter "E". 6. After a while, the following screen will be shown. Click on the [Finish] button. Preparations Preparations 3. This completes the driver installation.
Check whether computer and MRS-1044 are in the online state • The volume label for the MRS-1044 recognized as local disk differs depending on the operating system. In Windows 98, the volume label is shown as "None" and in Windows Me and Windows 2000 as "Local Disk". • The driver installation process must only be carried out once.
UIB-01 Applications The computer and MRS-1044 are now in the offline state, and you can terminate the USB connection. This section describes the various uses of the UIB-01. Project backup/restore In the offline state, the "USB Storage Unplug" icon should disappear from the task tray. If not, right-click on the icon and select [End of USB Storage Unplug]. 3. 5. Press the [ENTER] key of the MRS-1044. Power to the MRS-1044 is turned off.
3. Select the folder of the project you want to back up, and select [Copy] from the [Edit] menu on the menu bar. 4. Open the destination drive/folder and select [Paste] from the [Edit] menu on the menu bar. Restoring a project Select the folder for the project you want to restore, and select [Copy] from the [Edit] menu on the menu bar. 4. Open "My Computer" and double-click on the local disk representing the MRS-1044. 5. Select [Paste] from the [Edit] menu on the menu bar.
Returning the MRS-1044 to the factory default condition The supplied CD-ROM contains complete data about the factory default settings of the MRS-1044. Using the application program "Factory Recovery Tool", you can automatically copy these data to the hard disk of the MRS-1044, thereby restoring the MRS-1044 to the factory default condition. Formatting the hard disk of the MRS-1044 4.
NOTE (2) • To return the MRS-1044 to the factory condition, be sure to use the Factory Recovery Tool. Simply copying the FACDAT folder to the MRS-1044 will not perform a restore, and the MRS-1044 will not operate normally. (1) Using the Audio File Manager Installing the software 1. 2. 3. 26 Insert the supplied CD-ROM into the CD-ROM drive of the computer, and double-click on the "UIB_01_CD" icon in "My Computer". Click on the "UTY" folder, and select [Copy] from the [Edit] menu on the menu bar.
Reference Information MRS-1044 hard disk contents ● This section describes the contents of the internal hard disk of the MRS1044 that can be checked from the computer. Open "My Computer" and double-click on the MRS-1044 recognized as local hard disk. This will display the contents of the disk. SYSTEM.ZEX file MRS-1044 system file ● CURSNGNO.INI file Last edited project number data ● PATCH.DAT file Effect patch data used for new projects ● RHYTHM.
Troubleshooting ● FACDAT folder This folder contains the data for returning the MRS-1044 to the factory default settings. ● UTY folder This folder contains the "Audio File Manager" software for exchanging audio data between the computer and the MRS-1044. For information on use of the software, see p.26. ● ● UNINST file This is the software for uninstalling the installed driver. To uninstall, double-click on this file and follow the instructions that appear on the screen.
ZOOM CORPORATION NOAH Bldg., 2-10-2, Miyanishi-cho, Fuchu-shi, Tokyo 183-0022, Japan PHONE: +81-42-369-7116 FAX: +81-42-369-7115 Web Site: http://www.zoom.co.
