Owner's Manual
Table Of Contents
- Operation Manual
- Table of Contents
- Features
- Parts & Controls
- Getting Started
- Recording Flow
- Easy Recording Guide (Stereo Mode)
- Parts and Controls
- Battery / Power Setting
- Power / Hold Switch
- Recording and Transport Buttons
- Track 1-4 Buttons
- Input, Mic, 1 and 2 Buttons
- Record Level and Volume Buttons
- Dial and Menu Buttons
- Loading an SD Card
- Setting Date and Time
- Connecting External Devices
- Built-In Microphones
- External Mic with Power Plug
- Input 1 / 2 Connections and Phantom Power
- Using a USB Audio Interface
- Using as a USB Card Reader
- Built-In Speaker
- Mode Overview
- Switching and Confirming Modes
- Mode Details
- Mode Screens
- Optional Remote Control
- Operations
- Reference
- Main Specifications by Mode
- Settings Available in each Mode
- MTR Mode Effect Types and Parameters
- H4n Pro Patch List
- Specs
- Troubleshooting
- Index
- Supplied Accessories
- Cubase LE Startup Guide
- Warranty
143
9LMLYLUJL4;9TVKLLɈLJ[[`WLZHUKWHYHTL[LYZ
4;9TVKLLɈLJ[[`WLZHUKWHYHTL[LYZ
Q,-?TVK\SLZ
O*VTWYLZZVYSPTP[LYLɈLJ[Z
RackComp
Compressors reduce high-level signals and raise the
minimum level.
(1) THRSHOLD 0–50
Sets the base level from which the compressor
operates.
(2) RATIO 1–10
Sets the compression ratio.
(3) ATTACK 1–10
Sets how quickly compression starts.
(4) LEVEL 2–100
Sets the level of the signal after the EFX module.
LIMITER
3PTP[LYZJVTWYLZZ^OLUPUW\[ZPNUHSZL_JLLK[OLÄ_LK
level.
(1) THRSHOLD 0–50
This sets the base level from which the limiter
operates.
(2) RATIO 1–10
Sets the compression ratio.
(3) RELEASE 1–10
Sets how quickly the limiter stops functioning
after the signal goes below the base level.
(4) LEVEL 2–100
Sets the level of the signal after the EFX module.
O4VK\SH[PVULɈLJ[Z
AUTO WAH
;OPZ^HOLќLJ[YLZWVUKZ[VJOHUNLZPUPUW\[ZPNUHS
strength.
(1) POSITION
Before,
After
Sets the insertion point of the EFX module.
Select before or after the PREAMP.
(2) SENSE
ò¶ò
1–10
:L[Z[OLLќLJ[ZLUZP[P]P[`
(3) RESONANC 0–10
Sets the amount of resonance.
(4) LEVEL 2–100
Sets the level of the signal after the EFX module.
PHASER ;OPZLќLJ[]HYPLZ[OLZV\UK^P[OWOHZPUN
(1) POSITION
Before,
After
Sets the insertion point of the EFX module.
Select before or after the PREAMP.
(2) RATE
0–50, ʖ
(See P.146)
Adjusts the speed of modulation.
(3) COLOR
4STAGE,
8STAGE,
INVERT4,
INVERT8
:LSLJ[[OLLќLJ[ZV\UK[`WL
(4) LEVEL 2–100
Sets the level of the signal after the EFX module.
TREMOLO ;OPZLќLJ[YHPZLZHUKSV^LYZ[OL]VS\TLJ`JSPJHSS`
(1) DEPTH 0–50
Adjusts the modulation depth.
(2) RATE
0–50, ʖ
(See P.146)
Adjusts the speed of modulation.
(3) WAVE
UP 0–9
DOWN 0–9
TRI 0–9
Select the modulation waveform from UP (rising
sawtooth), DOWN (falling sawtooth) and TRI
(triangle) types.
The higher the number, the more the wave peaks
HYLJSPWWLKLTWOHZPaPUN[OLLќLJ[
(4) LEVEL 2–100
Sets the level of the signal after the EFX module.