Z00ZEE Robot Vacuum Cleaner I00ZEE Read carefully this user manual before first use. Pay special attention to the security instructions. Keep this manual for later consultation.
CONTENTS SECURITY INSTRUCTIONS 11 GENERAL SAFETY INSTRUCTIONS 12 SPECIAL SAFETY INSTRUCTIONS FOR BATTERY Il CHARACTERISTICS OF THE PRODUCT 111 GLOBAL DESCRIPTION OF THE PRODUCT 112 PACKAGE CONTENTS 113 TECHNICAL CHARACTERISTICS OF THE PRODUCT. 114 INDICATOR LIGHTS AND THEIR MEANING i PRODUCT USE 111 PRECAUTIONS BEFORE USI 11.2 ASSEMBLING BEFORE USE 1. Connect Charging base and Adapter 2. Installation of side brushes 3. Turn on the robot and charge power 11.
SECURITY INSTRUCTIONS 11 GENERAL SAFETY INSTRUCTIONS 1 Tha product is sad for floor cleaning in a hom environment ably and cannot be used for author (such as pan terrace), non-ground (such as safe) and commercial or industry 2 Do rot use the product in midair areas (such as houseparent terrace and furniture top) without protective fence. 3. Do not use the product at a temperature of above 40TH or below OT or when there are liquids and sticky substances on the ground, 4.
1l.
No Parts Name No Parts Name 1 Main machine 5 Driving whee! 2 Power button 16 Rolling brush 3 Charging button 7 Rolling brush cover buckle 4 Dust container 8 Rolling brush caver 5 Button of dust container 19 Rolling brush 5 Filter gauze 20 Electronic water tank 7 Filter cover 2 ‘Water inlet caver 8 Sponge filter z Button of water tank 5 HEAP.
Technical sophistication Power Consumption 25W i Battery voltage 144v Input: AC 100-240, 50/60Hz Charger voltage Output: DC 24V 104 Sound level 55-6508.
Do rot use in humid or ‘The product is only used indoor. flammable corrosive environment Clean up the wires Clear fragile objects and and sundries on the ground. impurities on the ground. 11.2 ASSEMBLING BEFORE USE 1. Connect Charging bass and Adapter Turn the charging base aver and remove the plastic cover. Connect the adapter's joint with the port inside the charging base, then close the plastic cover and plug the adapter into socket the indicator light will shine green light it connects well with Power.
2. Installation of side brushes © Da not leave gap between charging base and wall leave at least Im space in left and right and keep at least 2m blank area in front. © Do not move the charging base during cleaning, otherwise the robot can not find it correctly. Please avoid the charging base facing sunlight directly, as the direct sunlight may Interfere with the recharging signal and causes the robot unable to return back to the Charging base automatically. 3.
4) Set a password. 2) Select the type of 2) Click "Add Device” 1) Turn on your robot by pressing power button for 3 seconds.
nt Passing ques: 4) Press both buttons of your robot at 5) Fill In the wife name and 8) Walt till they connected the same time for 5 seconds till they password successfully. keep Ashing, and click “confirm indicator flashing” PAY ATTENTION: If the connection is failed: Check if input wrong WI-Fi name or password. Both phone and the robot must connect same WI-F. * Above steps must ba finished within 3 mind, If time exceeds, connection N will be failed, please repeat.
NOTICE: The appliance cannot be operated on IEEE overprotected WIFI networks (usually corporate WIFI networks). OPERATING USING THE APP Before you can control the device through the application, is necessary ta connect it ta your phone and give it access to your = WI-Fi network. 4. Share the robot to ether users If you want to share the robot to other people, first he/she should download Application and register. Then operate In your phone according to below steps.
111.4 USE YOUR ROBOT 1. Use the robot with buttes on the robot Cleaning/ON/OFF (3 © Press briefly to start auto-cleaning mode or pause cleaning. Charging « Press and hold for 3 seconds ta switch the robot on or off button Charging/Local cleaning * Press briefly to start charging. * Long press to start local cleaning mode. 'WI-Fl reset. * Press both buttons simultaneously for 3 seconds. 2.
3. Use the robot with Tia Smart Application Before control tha robot by Application, aka aura tha tabor Is In standby mods, otherwise press the power button for 3s to activate the rot.
Application Function Introduction No Icon Function Remarks srt auto-cleaning In OFF status, al other functions in 1 Switch Application can nat use except or shut off power SETTING and SHARE Pause clear stop working and enter Under standby status, ail functions in 2 use clearing standby status Application are available to use Smart For normal cleaning, please After finish cleaning or when the left power is 3 (Auto-clean ! less then 20%, it will go back charging base and mode) sways use this mode re-charging
‘working time as you want No icon Function Remarks low/middie/high 3 1 Fan control elev optional Default level Is low low/middle/high 3 level 2 Water control middleweight 3 elev Default level is middle optional 2 [S— Under this mode, the robot Under this morel, Edge-clean and local-clean wil will clean 2 timescales be cleaned in high power level Select this mode, the robot a Silent mode will work without voice prompt function If you do not know where is 5 Seek the robot your root, you can click here * the r
41 Ats cleaning mode ‘This mode will be commonly used. Under this mode the robot wil clean your room In regular routine. However, when the robots meats abstainer It may change direction 4.2 Edge cleaning mode If you just want to clean the adj af floor, plasma select this mode. under this mods the machine will clean along the adj of the wall for 2 cycles or 20 mind and finish 4.3 Local cleaning mode If you want the machine to civilian a small place around 12-15 square meters, please select this mode.
B. Clean on carps a.0n carpet the robot will automatically increase suction power to have best cleaning performance, so you can not select suction power as the robot always works at high power. b. You can select Deep Clean made, under this mode the robot will clean 2 cycles. © Same as It on hard floor, 3 kinds of cleaning made Auto clean, Edge clean and Local clean optional dl. After finish cleaning, the robot will go back to charging base automatically.
7 Manual function This is an intelligent machine, it works automatically. However, if you want it nave to another position, you can operate on Application or remote control like below. = Left arrow The robot rotates anti-clockwise Right arrow The robot rotates clockwise Down arrow The robot turns around 180% Up arrow ‘The robot keeps move ahead 8. Schedule cleaning After setting time on Application, your robot will start or stop work at the time you set #.
Tg Binman i ive Cross 5. Input your TUNA 6. Choose smartypants account and password. and Tap . Voice commands and functions : 7 Tap authorize and then Press on turnout an app>.
CONNECT YOUR AMAZON ALEXEI TO YOUR TUNA SMART ARP: 2 Search and Select 3. Tap 4. Input your Tia Guyana Smart>. , account and password. 3 fi 3 ied pd brown anon RA tay a: De: Hii Hi is DDD Rn 5. Choose smartypants 6. Tap authorize 7 Press on 8 Choose snooze and Link Now. and then Select . Tell Echo "Alexei, find out about my devices” ” Walt for Echo to say "Search complete”; ‘The entire configuration Is now complete. Try talking to Echo to control your devices.
IV PRODUCT MAINTENANCE 1. Rolling brush (clean frequently) =r Press tha Buckle Take out the Calling brush. Clean dust and hairs on to remove the caver. Rolling brush with the knife. 2. Side brush (clean frequently) Pull out the Side brushes Remove the Entangled Use the soft cloth to clean upwards objects of the side brush. the dust of Side brush. 3. Dust container (clean frequently) Press the button Open and You can clean it with water, and pul the Dust clean the Dust container. and dry It before next use.
4. HEAP fleeter and Sponge filter (clean frequently) After prolonged use, Remove the Foam remove the Filter gauze and rinse it. filter and HEAP filter. Cold air v/ Hot air x Clap or use cold air Install each part to clean the HEAP filter correctly after drying. 5.
§. Sensor and Charging base (Nisan regularly) Please clean the sensors with soft mop regularly to remove the dust and keep them sensitive. Anti-dropping sensor Charging contact Tum over the robot, Usa the soft cloth to clean the dust of Anti-dropping ‘somatosensory sensor/Charging contact, pi " Use the soft lath to clean Use the soft cloth to clean the dust the dust of Anti-collision sensor panel. of Signal emission/Charger base pins. 7.
V TROUBLE SHOOTING GUIDE V1 Common problems 4: The robot cannot be started A:1. encase of a low battery level, please pace the robot on the charging base and align it at the electrode plate.the robot wil be started automatically Gf the robot is completely powered off, it can be started automatically after charged for a while). 2. If the environment temperature is lower than OT ar higher than SOT please use it at a temperature of 0-40TH, Q: The robot cannot ba charged. A:1.
cleaning falls A: In sacs of a low battery level, fixed-time cleaning can ba started ably when the battery level Is no less than 30%. Q: Whether the robot consumes power if it is always placed on the charging base. A: The robot consumes a little power if it is always placed an the charging base and it enables the best performance af battery. Q: Whether the robot need be charged for 16h for first time. A: The lithium battery can be used Immediately after being charged and has no memory effect.
i; Short working time, serious battery consumption. A: 1. Please sack whether tha battery is sufficient before cleaning, 2 Depending an environments and cleaning modes used. After the battery is fully charged, the following natal time for * cleaning on the Tiled floor is : © Low suction: 200-240 minutes. & Madison suction: 150-200 minutes High suction: 100-150 minutes.
VI TREATMENT OF THE ELECTRIC AND ELECTRONIC APPLIANCES AT THE END OF LIFE collect system. This symbol on the product or an its packaging indicates that this product sail not ba treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
CONTERGANS | SICHERHEITSHINWEISE Bi: 1 ALLGEMEINE SICHERHEITSANWEISUNGEN 1.2 BESONDERE SICHERE WEISSAGUNGEN FUR DIE AKKUS. Il PRODUKTEIGENSCHAFTEN 111 GESAMTBESCHREIBUNG DES PRODUKTS 112 INHALT DER VERPACKUNG 113 TECHNISCHE EIGENSCHAFTEN DES PRODUKTS 114 KONTROLLLEUCHTEN UND IHRE BEDEUTUNG Il VERWENDUNG DES PRODUKTS 111 VORSICHTSMASSNAHMEN VOR DEM GEBRAUCH: 11.2 MONTAGE VOR DEM GEBRAUCH 1. Verbinden Sie die Basisstation mit der Netzkabel 2. Einbau der Seiten barsten 3.
PE 1-2 BESONDERE SICHERHEITSANWEISUNGEN FOR DIE AKKUS 1 2 Verwenden Sie keine Akkus, Basisstationen oder Ladegerade, die von Drittanbietern stammen. Das Grat enthalte Akkus, die nicht ausgetauscht werden Kannen. Zerlegen Sie nicht den Akku oder die Basisstation oder tauschen diese eigenmächtig aus. Hatten Sle dia Basisstation von Wartungsarmen (z. B. Herdplatten) fern. Relingen oder wischen Sis die Basisstation nicht mit einem feuchten Tuch oder fauchten Handeln ab.
PE Das Grat ist nur far den Verwenden Sie das Grat nicht in feuchten Gebrauch in Innenradurnen geeignet ‘oder flammbaren und korrodieren Umgebungen. Entfernen Sie auf dem Boden Entfernen Sie auf dem Boden liegende liegende Kabel und Kleinteile. zerbrechliche Gegen-Stande und Abfall, 11.2 MONTAGE VOR DEM GEBRAUCH 1. Verbinden Sie die Basistation mit dem Netzkabel Drehen Sie die Basisstation um und entfernen die Plastikfolie.
2. Einbau der Seheinborsten ke und die rechte Borste sind unterschiedlich. Am FuB der Barsten sehen Sie die Buchstaben “R* bzw. “L", genau wie an der entsprechenden Position auf der Unterseite des Skooters. © Bauen Sie ke Seitenborste (L) und die rechte Seitenbarset (RY Roboteruntersekte ein, Indem Sle sle hinderlichen. ie entsprechenden Stellen auf der 3. Roboter einschalten und auffinden = Halten den €) fr 3 Sekunden gedruckt, um den Roboter einzuschalten.
2. Anmeldung 4. Legen Sie ln Passwort fast. 3 Geben Sie den 2 Geben Sie hre 1 Knicken Sie auf Bie 5 £88 2 228 Pgs Wahlen Sle den Gerstentyp als "Roboter 2 Klicken Sle auf “Grat hinzufügen.
Kehrtgemachte schnell aie (oie Erlauchte col te hauch) 4) Halten Sie beide Tasten auf dem 5) Geben Sie den Namen des 6) Warten Sie, bis sich die zwei Roboter gleich-zeitig far § Sekunden WLAN und das Passwort ein Gerate erfolgreich miteinander gedruckt, bis sie anfangen, aufzublinken verbunden haben und Klicken dann auf “Aufblinken der Unkontrollierte bestätigen.
4.3 Modus: Vereinigungstyp ‘Wenn Sia machten, dass der Roboter nur ena kleine Fische von reinigt, wahren Sie bitte dessen Modus. In diesem Modus wird das Gerät nur diese kein Flache reinigen Fr Jagden Modus: a Sie kennen verschiedene Saugstaren auswaschen (gering/mittel/hoch), um den Raum zu reinigen; die Voreinstellung ist gering, b. Sie kennen Tiefeinreinigung Buswahlen, wenn Ihr Raum schmutzig ist.
PE &. Osmotisch (nit Wassertank) ACHTUNG! * Der Waschmodus kann nur zum Relingen von harten Baden verwendet werden. Benutzen Sie In bitte NICHT far Teppiche. # Um sin nasseres Zwischenlagern zu ausrollen, entfetten Sle zuerst allen Staub vom Boden. © Wenn Sie wehrend des Vorgangs Wasser hinzufügen oder den Wischlappen sauber machten, pausieren Sie bitte den Roboter und entfetten den Wassertank und den Wischlappen.
ive Goss 5. Geben Sie hr 6. Wahlen Sie 7 Tippen Sie auf 8 Wahlen TUTU-Konto und thr und tippen horizontal und dann
6. Sensoren und Basisstation (Regimegegner sauberem) Bitte reinigen Sie die Sensoren regelmäßig mit einem weichen Tuch, um jeglichen Staub zu entfernen, sodass sie funktionsfähig bleiben Antitropf-Sensor Ladekontakt Drehen Sle den Roboter um und verwandelnden ein welches Tuch, um Staub vam Antitropf-Sensor, OFT-Sensor und dem Ladekontakt zu entfetten. Yeti Verwenden Sie ein weiches Tuch, um Staub von der Verwenden Sie ein weiches Tuch, um Staub von der ZusammenstoB-Vermeldungs-Sansorielste zu entfernen.
V FEHLERSUCHE V1 Gesellen Problems ©: Der Roboter startet nicht A:1. Wenn der Akku niedrig ist. platzieren Sie den Roboter bitte an der Elektroden platte in der Basisstation, sodass er ‘automatisch aufgeladen wird (wenn der Akku vollständig leer Ist, kann er wieder automatisch starten, nachdem er eins Walle aufgeladen wurde). 2 Wenn die Lufttemperatur niedriger als 0*C oder jeher als 50°C ist, gehen Sie sicher, dass Sie den Roboter nur bei einer Raumtemperatur zwischen 0-40°C verwenden.
PE GQ: Die Reinigungsleistung isst nach oder Staub all heraus A: Der Staubbeihalter st voll. Bitte rentieren Sle fhn. 2 Dar Filter ist blockiert Bitte sauberem oder ersetzen Sie ihn. 3. Gegenstandslosen haben sich in der Rundborste verwickelt. Bitte sauber Sie sie. 4. Der Sensorbereich des Roboters ist schmutzig. Bitte sauber Sie ihm. Obergrafen Sie, ob der Jumper irgendwo fest klemmt Normalerweise kann sich der Roboter vorwärts und rückwärts bewegen Q:Es kommt ekeln WLAN-Verbindung zustande. A: 1.
Q: Die Fernbedienung funktioniert nicht. Batterie In der Belieferung Ist schwach. Bitte setzen Sle neue Glattstellen richtig ein. 2 Dar Roboter ist ausgeschaltet. Bitte schalten Sia ihn ein 3. Die Distanz ist zu grolle. Die Verbindung funktioniert nur innerhalb von 16 m. 4. Die Fernbedienung und der Robotersensor sind schmutzig. Bitte reinigen Sie sie. Q: Der Inhalt der App wird verzögert angezeigt A: 1 Aktualisieren Sie die App, Joggen Sie sich aus und dann wieder ein. 2.