User manual Washing Machine PWG 61051
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Frost precaution _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 4 5 6 6 Special accessories _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
• After having installed the appliance, check that it is not standing on the inlet and drain hose and the worktop is not pressing the electrical supply cable against the wall. • Install the appliance on a flat hard floor. • Never place cardboard, wood or similar materials under the appliance to compensate for any unevenness in the floor. • If the appliance is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely under the appliance.
To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin. To disable this device and restore the possibility of closing the door, rotate the button anti-clockwise until the groove is vertical. Frost precaution If the appliance is installed in a place where the temperature could drop below 0°C, proceed as follows to remove any water remaining inside the appliance: 1. unplug the appliance; 2. turn off the water tap; 3.
>PE<=polyethylene >PS<=polystyrene >PP<=polypropylene This means that they can be recycled by disposing of them properly in appropriate collection containers. Ecological hints To save water, energy and to help protect the environment, we recommend that you follow these tips: • Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!). • The machine works more economically if it is fully loaded.
Technical data Dimensions Width Height Depth Depth (Overall dimensions) 60 cm 85 cm 50 cm 54 cm Electrical connection Voltage - Overall power - Fuse Information on the electrical connection is given on the rating plate, on the inner edge of the appliance door. Water supply pressure Minimum Maximum 0,05 MPa 0,8 MPa Maximum Load Cotton 6 kg Spin Speed Maximum 1000 rpm Installation Unpacking • Remove the external film. Use a cutter, if necessary.
• Return appliance to it's upright position. • Open the door and remove the plastic hose guide, the bag containing the instruction booklet and the plastic plug caps from the drum. • Unscrew the three bolts (A) and remove the hose holders (C). • Slide out the relevant plastic spacers (B). Warning! Do not remove the drain hose from the rear support. Remove this hose only if it is necessary to drain the water. Refer to "Frost precaution" and "What to do if".
Positioning and levelling Water inlet Connect the hose to a tap with a 3/4” thread. 35° 45° x2 Level the appliance by raising or lowering the feet. The appliance MUST be level and stable on a flat hard floor. If necessary, check the setting with a spirit level. Any necessary adjustment can be made with a spanner. Loosen the ring nut to angle the hose to the left or right depending on the position of your water tap. Do not place the inlet hose downwards.
If the outlet spigot has not been used before, remove any blanking plug that may be in place. MAX 100cm • Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. Tie the plastic hose guide to the tap with a string to prevent that the drain hose unhooks when the appliance is emptying. • Onto a sink outlet spigot. The end of the drain hose must always be ventilated, i.e. the inside diameter of the drain pipe must be larger than the outside diameter of the drain hose.
Electrical connection • The appliance must be earthed. • Make sure that the electrical information on the rating plate agree with your domestic power supply. • Always use a correctly installed shockproof socket. • Do not use multi-way plugs, connectors and extension cables. There is a risk of fire. • Do not replace or modify the mains cable yourself. Contact the After Sales Service. • Make sure that the mains plug and cable is not squashed or damaged by the back of the appliance.
Rust: oxalic acid dissolved in hot water or a rust removing product used cold. Be careful with rust stains which are not recent since the cellulose structure will already have been damaged and the fabric tends to hole. Mould stains: treat with bleach, rinse well (whites and fast coloureds only). Grass: soap lightly and treat with bleach (whites and fast coloureds only). Ball point pen and glue: moisten with acetone1), lay the garment on a soft cloth and dab the stain.
PU SH RE TO MOV CL E EA N PU SH RE TO MOV CL E EA N If the water hardness degree is medium or high we suggest you to add a water softener following always the manufacturer’s instructions. When the degree of hardness is soft, readjust the quantity of the detergent. Open the detergent dispenser drawer Compartment for powder or liquid detergent used for main wash. Compartment for liquid additives (fabric softener, starch).
• Powder detergent. • With programmes with prewash. • Do not use liquid detergent if the washing programme doesn't start immediately. • Rotate the flap downwards. • Carefully put the drawer back. In all above listed cases, use the flap in "UP" position . Measure out the fabric softener • Measure out the detergent. Pour fabric softener or any additives into the compartment marked (do not exceed the «MAX» mark in the drawer).
Programme selector dial Speciali Cotone Cotoni Jeans con Prelavaggio Mini 30 1 Piumoni Eco Sintetici Stiro Facile Mix Centrifuga Scarico Risciacquo Lana Delicati Turn the programme selector dial to the required programme. The selector dial can be turned either clockwise or counter-clockwise. The green pilot light of the button 6 starts flashing: the appliance is now switched on.
The start of the programme can be delayed by 8 or 4 hours by means of this button. The relevant light illuminates. You must select this option after you have set the programme and before you start the programme. Select a delayed start: • select the programme and the required options; • select the delay start by pressing the button 4; • press the button 6: – the appliance starts its hourly countdown. – The programme will start after the selected delay has expired.
Start the programme by pressing the button 6 • To start the selected programme, press the button 6, the corresponding green pilot light stops flashing. The pilot light A illuminates to indicate that the appliance starts operating and the door is locked. If you have chosen a delayed start, the appliance will begin the countdown. • To interrupt a programme which is running, press the button 6: the corresponding green pilot light starts flashing.
Stand by: during programme setting up and once the programme has finished, if the programme selector dial and any button are not touched, after a few minutes the energy saving system is enabled. The pilot lights go off. The green pilot light of the button 6 flashes with a low frequency. By pressing any button the appliance will come out of the energy saving status. Door seal At the end of every cycle, check from the door seal and remove objects that could be trapped in the fold.
Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options MIX 20° Main wash - Rinses - Maximum spin speed at 1000 rpm Max. load 3.5 kg Highly energy efficient cold wash programme for lightly soiled laundry. This programme requires a detergent which is active in cold water. SPIN REDUCTION ANTIPIEGA PARTENZA POSTICIPATA MORBIDEZZA 5 RISCIACQUI DELICATI (Cold) 40°Main wash - Rinses - Maximum spin speed at 700 rpm Max. load kg 3.
Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Detergent Compartment Options STIRO FACILE (Cold) 60°Main wash - Rinses - Maximum spin speed at 900 rpm In order to obtain the best anti-creasing result, reduce the load of synthetic items. (Recommended load 1 kg) Synthetic or mixed fabrics. Gentle wash and spin to avoid any creasing. The appliance performs additional rinses.
cotton laundry. They are suitable to clean normally soiled cotton laundry and they are the most efficient programmes in terms of combined energy and water consumption for washing that type of cotton laundry. They agree with EN60456. The actual water temperature may differ from the declared cycle temperature. Care and cleaning Warning! Switch the appliance off and remove the mains plug from the socket before any cleaning action.
• turn the drum and align the filter cover (FILTER) with the arrow on the door seal; • open the filter cover by pressing the special hook and by rotating the cover upwards; Warning! Keep the filter cover open until the filter removal. • before removing the filter, remove any fluff or small objects from around the filter; The filter is inserted correctly when the indicator on its top is visible and blocked. • close the filter cover; • insert the mains plug again.
• Unscrew the hose from the appliance. Keep a towel nearby because some water may flow. • Clean the filter in the valve with a stiff brush or with the piece of cloth. • Screw the hose back to the appliance and make sure the connection is tight. • Turn on the water tap. What to do if… The appliance does not start or stops during operation.
Lavaggi o Morbi dezza 5 Ri s ci acqui Fi ne ci cl o Avvio/Pausa The drain hose is squashed or kinked. • Check the drain hose connection.
Malfunction Possible cause / Solution The appliance does not start: The plug is not properly inserted in the power socket. • Insert the plug into the power socket. There is no power at the socket. • Please check your domestic electrical installation. The main fuse has blown. • Replace the fuse. The programme selector dial is not correctly positioned and the button 6 has not been pressed. • Please turn the selector dial and press the button 6 again. The delay start has been selected.
Malfunction Possible cause / Solution Spinning starts late or the appliance does not spin: The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after 10 minutes, the laundry is still not evenly distributed in the drum, the appliance will not spin.
www.electrolux.
