User Guide

Quick Start Guide
PROFESSIONAL SECURITY MADE EASY
The system may not include HDD depending on the kit you selected. This system works with most 3.5” SATA
HDD or 2.5” SATA HDD.
1. Install a hard drive (if your system has preinstalled HDD, please skip this step)
2. Record video
Right click mouse > Go to Main Menu > Setup > Record
You shall see the record settings for all channels. Change the record setting according to your preference and apply the
changes.
Get into system Main Menu > Search, system presents picture as following.
①
Unplug your DVR from power, unscrew and remove the top cover.
②
Connect the SATA power and data cables from the DVR to the corresponding ports on your HDD (as shown).
③
Place the HDD into the DVR. Any cable should cross up over the HDD.
④
Holding the hard drive and the DVR, gently turn it over and line up the holes on the hard drive with the holes on the
DVR. Using a Phillips screwdriver, screw the provided screws into the holes. Assemble the cover.
5. Record video
6. Playback video
7. Motion Detection
8. Backup the video for memory
9. Connect to WiFi
10. Upgrade the DVR
①
③
②
④
Select the channel
Start playing
Search the video you want via time or Event, then play it.
Previous Record: Move to last recorded event
Next Record: Move to next recorded event
Fast Forward: video can be played at different speed, from
1/4 times to 16 times.
Rewind: Video play can be rewinded at 1 time, 8 times, 16
times and 32 times.
Screen Display Mode: Both single-screen and multi-screen
are available. You can choose how many channels you want
to playback one time.Channel without records presents
blank screen.
Previous Record
Next Record
Rewind
Fast
Forward
Play/Pause
Next frame
Previous
frame
Single-screen display
Multi-screen display
Select Camera. Tick the Channel you want to record on
motion detection.
Holding Time. Set recording time length after motion stop.
Trigger. Multi-channels can be set to record when detect
the motion by one of cameras.For example,when camera 1
detects motion,camera 2 and camera 3 can be triggered to
record as well.
Area. It is allowed to set sensitivity area of camera viewing
range.
Click STAR to make the whole viewing range as
sensitivity area;
Click Trash Box to remove sensitivity area;
Click and drag mouse to draw or erase the sensitive area.
Right click mouse > Main Menu > Setup > Alarm > Motion > Motion detection.
The system records when motion is detected by the camera. An icon is shown when motion is detected.
1. Plug an USB flash disk to your DVR’s USB port.
2. Right click the mouse > Main Menu > Backup >
choose the channel and time period > Search > Choose
the video clips you want to backup > Click Backup.
Click to save setting
Click to exit
Only wireless dongle RT3070 can be supported
by the DVR.
Step 1. Connect WiFi USB Dongle to USB2.0 port.
Step 2. Right click Mouse > Main Menu > Setup >
Network > WiFi Setup.
Note: It needs to connect the WiFi device again after
unplugging.
Step 3. Click Search Signal to choose a WiFi signal
and input corresponding WiFi password, click OK. When
it presents Connected, click Apply and Exit.
If your DVR need to upgrade , please contact us to get a
upgrade software.
Step 1. Put software into U-Disk, and ensure software is
at root directory as below.
Step 2. Put U-Disk into DVR port USB2.0.
Unplug the mouse from the front USB socket.
Step 3. Restart DVR(Power off and on), it will be
upgraded automatically.
Note: Please wait for a few minutes until DVR
interface presents.
Tick all Enable in options, and click OK to save.
After finishing download ActiveX controls, pop up login.
If the surveillance preview does not work with the above
settings, change the IP Address to 'Fixed' as follows.
Note: Check with your I.T manager before making these
changes
Step 1. Open the router
Step 2. Find the router Subnet Mask(for example:
255.255.255.0), Preferred(Primary)DNS server (for
example: 211.136.192.6), Altermate(Secondary)DNS
Server(for example: 114.114.114.114)
Step 3. Input Subnet Mask, Preferred DNS Server and
Altermate DNS Server in DVR menu accordingly, DVR
system menu path is : Main Menu > Setup > Network
Note:1. Please ensure the IP address you input is not
used by any other device, such as, computer, server,
etc.
2. Please ensure Subnet Mask,DNS Server in DVR
menu and Router System menu are same.
3. The system menu in different routers are different. But
Subnet Mask, Preferred DNS Server, Altermate DNS
Server can be found in all Router.
Click Test, if ‘OK’ is displayed, the network is connected
successfully.
As Color and luminance is important for sensitivity, so it's necessary to adjust its value at specific conditions. The default
value is 4 while value range is from 1 to 8.
Right click mouse to show or hide control menu at screen bottom.
Test the setting by moving something or some one walk through grid area within camera view range. If DVR detects
movement within grid area, a yellow hunanoid figure would be presented in the screen. The grid could not cover flag,
trees or some other flow objects in the wind to avoid false alerts.
2. When visit(live view)your DVR at the 1st time, the IE
browser settings should be, IE-Tools-Internet Options-
Security-Internet- Customization level
REC
ZS V1.1
4
5
6