ZOTAC ZBOX nano ZOTAC ZBOX nano User’s Manual No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ZOTAC.
ZOTAC ZBOX nano Table of Contents Product specifications--------------------------------------------------------------------------- 3 Safety information--------------------------------------------------------------------------------- 4 Setting up your system------------------------------------------------------------------------ 4 Care during use--------------------------------------------------------------------------------- 4 Welcome-----------------------------------------------------------------------
ZOTAC ZBOX nano Product specifications Product Dimensions • 127mm x 127mm x 45mm Onboard CPU • Intel Core i3-4020Y (dual core, 3M Cache, 1.5 GHz) • Intel Core i5-4210Y (dual core, 3M Cache, 1.9 GHz) Onboard graphics • Intel HD Graphics 4200 • HDMI 1.4a (3840x2160@30Hz, supports 4K display) • DP (2560x1600@60Hz) Memory support • One 204-pin DDR3L-1600/1333 SO-DIMM slot (1.35V) • Up to 8 GB of memory USB ports • Two USB 2.0 ports & four USB 3.0 ports Storage support • SATA 6.
ZOTAC ZBOX nano Safety information Your ZOTAC ZBOX nano is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system Read and follow all instructions in the documentation before you operate your system. Do not use this product near water or a heat source such as a radiator. Set up the system on a stable surface with the provided stand.
ZOTAC ZBOX nano Welcome Congratulations on your purchase of the ZOTAC ZBOX nano mini-PC. The following illustration displays the package contents of your new ZOTAC ZBOX nano. Please contact your retailer If any of the below items are damaged or missed.
ZOTAC ZBOX nano Getting to know your ZOTAC ZBOX nano Front view 3 1 2 5 4 7 6 8 Refer to the diagram below to identify the components on this side of the system 1. Power switch The power switch turns the mini-PC ON and OFF. 2. HDD status indicator The hard disk LED blinks when data is being written onto or read from the hard disk drive 3. WiFi status indicator The WiFi LED blinks when data is being transfered over WiFi. 4.
ZOTAC ZBOX nano Rear view 1 3 5 6 8 2 4 4 7 Refer to the diagram below to identify the components on this side of the system. 1. Power input (DC19V) The supplied power adapter converts AC power to DC power for use with this jack. Power supplied through this jack supplies power to the mini-PC. To prevent damage to the mini-PC, always use the supplied power adapter. 2. HDMI output The HDMI (High Definition Multimedia Interface) output supports 4K (3840x2160@30Hz) displays such as an HDTV or monitor.
ZOTAC ZBOX nano How to disable integrated IR receiver 1. 2. 2. Turn on the ZBOX nano mini-PC, then press to enter the BIOS SETUP UTILITY. Use the arrow keys to navigate to Features > Onboard Device Control, and select CIR Controller. Enter CIR Controller and select Disabled. Enabled: enable the internal IR receiver (default) Disabled: disable the internal IR receiver 3. 8 Press F10 to save the configuration and exit.
ZOTAC ZBOX nano Customizing the ZOTAC ZBOX nano Before installing hardware, please follow the instructions below to remove the cover of your ZOTAC ZBOX nano. 1. Remove the four screws securing the bottom cover into place. 2. Remove the bottom cover.
ZOTAC ZBOX nano Installing a memory module 1. Locate the SO-DIMM memory slot and insert a SO-DIMM memory module into the slot at a 45 degree angle. 2. Gently press down on the memory module until it locks into place by the arms of the memory slot.
ZOTAC ZBOX nano Installing a hard disk 1. Locate the hard disk bracket, remove the 2 screws, and remove the hard disk bracket as shown in the image below. 2. Install the hard disk bracket onto a 2.5-inch SATA hard disk with 2 screws. 3. Insert the hard disk into the socket and gently slide into the connector.
ZOTAC ZBOX nano 4. Reinstall the screws for the hard disk bracket.
ZOTAC ZBOX nano Connecting a S/PDIF cable 1. Connect the S/PDIF cable to the mini-Optical S/PDIF adapter. 2. Locate the front panel and connect the mini-Optical S/PDIF adapter to the headphone / mini-Optical S/PDIF jack.
ZOTAC ZBOX nano Setting up the ZOTAC ZBOX nano Please connect your peripherals before using your ZOTAC ZBOX nano. 1 2 3 1. Connecting a DisplayPort display Connect the DisplayPort connector to the DP port. 2. Connecting USB 3.0 device Connect USB 3.0 devices such as external hard drives, SSDs and flash drives to the USB 3.0 port. 3. Connecting the WiFi antenna module Connect the included WiFi antenna to the WiFi antenna connector.
ZOTAC ZBOX nano 4 5 6 7 4. Turning on the system Connect the supplied AC adapter to the DC IN jack on the system rear panel and then press the power switch on the front panel to turn on the system. 5. Connecting to an HDMI display Connect one end of an HDMI cable to the HDMI port on the system rear panel and the other end to a HDMI-compatible display such as an HDTV or monitor. (When both the HDMI and the DP are connected, the audio output is from HDMI by default.) 6.
ZOTAC ZBOX nano Positioning the ZOTAC ZBOX nano • Do not position the ZOTAC ZBOX nano where the ventilation holes are covered. To guarantee proper use, leave 4 inches (10 cm) of spacing in front of the ventilation holes. • ZOTAC ZBOX nano mini-PC systems provide ample connectivity in a tiny form factor, please choose connectors and cables in appropriate sizes to avoid interference.
ZOTAC ZBOX nano 3. Connect the ZOTAC ZBOX nano to your LCD monitor with an HDMI/DP cable.
ZOTAC ZBOX nano Installing drivers and software Installing an operating system The ZOTAC ZBOX nano does not ship with an operating system preinstalled. The user must install the operating system before the ZOTAC ZBOX nano can be used. The following operating systems are supported: • Windows 7 • Windows 8 Follow the instructions below to install an operating system: 1. Attach external DVD drive via USB. 2. Insert disk for operating system 3. Wait for the ZOTAC ZBOX nano to boot from the disk. 4.
ZOTAC ZBOX nano Click the icon to review the Page 2 of the driver DVD: • Intel Rapid Storage Technology Each driver must be installed individually to ensure proper operation of the ZOTAC ZBOX nano. 3. Select the driver you want to install. The driver installer should launch. 4. Follow the onscreen instructions for the selected driver to install. 5. Restart the system. Using your ZOTAC ZBOX nano Configuring wireless connection Please follow the instructions below to connect to a wireless network: 1.
ZOTAC ZBOX nano Using a dynamic IP (PPPoE connection) 1. 2. 3. 4. 5. 6. Repeat Step 1-3 in the previous section. Select “Obtain an IP address automatically” and click “OK”. Click “Create a new connection” to start the NEW Connection Wizard. Click “Next”. Select “Connect to the Internet” and click “Next”. Select “Set up my connection manually”. 7. Select your connection type and click “Next”. 8. Enter your ISP Name and click “Next”. 9. Enter your User name and Password. Click “Next”. 10.
