ZOTAC ZBOX ZOTAC ZBOX User’s Manual No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means,except documentation kept by the purchaser for backup purposes, without the express written permission of ZOTAC.
ZOTAC ZBOX Table of Contents Product Specifications--------------------------------------------------------------------------- 3 Safety information--------------------------------------------------------------------------------- 4 Setting up your system------------------------------------------------------------------------ 4 Care during use--------------------------------------------------------------------------------- 4 Welcome----------------------------------------------------------------------------
ZOTAC ZBOX Product Specifications q Chipset v Intel® HM65 q Product Size v 188mm x 188mm x 44mm q Microprocessor support v Intel® Celeron 857 q Operating systems: v Supports Windows 7 32bit/64bit q System Memory support v Two 204-pin SO-DIMMs DDR3-1333 v Up to 16 GB of memory q USB Ports v Two USB 3.0 ports on the back panel v Four USB 2.0 ports (one front panel port, one top panel port and two rear panel ports) q Onboard Serial ATA v SATA 6.
ZOTAC ZBOX Safety information Your ZOTAC ZBOX is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system Read and follow all instructions in the documentation before you operate your system. Do not use this product near water or a heat source such as a radiator. Set up the system on a stable surface with the provided stand.
ZOTAC ZBOX Welcome Congratulations on your purchase of the ZOTAC ZBOX. The following illustration displays the package contents of your new ZOTAC ZBOX. If any of the below items is damaged or missed, contact your retailer.
ZOTAC ZBOX Getting to know your ZOTAC ZBOX Front view 1 2 3 4 5 6 7 Refer to the diagram below to identify the components on this side of the system 1. Headphone/Audio Out jack The stereo headphone jack (3.5mm) is used to connect the system’s audio out signal to amplified speakers or headphones. 2. Microphone jack The microphone jack is designed to connect the microphone used for video conferencing, voice narrations or simple audio recordings. 3.
ZOTAC ZBOX Rear view 1 2 3 4 5 6 7 8 Refer to the diagram below to identify the components on this side of the system. 1. WiFi antenna connector The WiFi antenna connector supports WiFi antenna module. 2. USB 3.0 ports The USB 3.0 port supports the SuperSpeed USB 3.0 devices and is backwards compatible with USB 2.0/1.1 devices. Use this port for USB 3.0 devices for maximum performance with USB 3.0 compatible devices. 3.
ZOTAC ZBOX Installing Hardware inside ZOTAC ZBOX Before installing hardware, please follow the instructions below to remove the cover of your ZOTAC ZBOX. 1. Unscrew. 2. Gently remove the cover as the image below. Installing a memory module 1. Locate the SO-DIMM memory slots and insert a SO-DIMM memory module into the slot at a 45 degree angle. Note: When installing two SO-DIMM memory modules, please insert a module into the lower slot first.
ZOTAC ZBOX 2. Gently press down on the memory module until it locks into place by the arms of the memory slot. Note: This ZOTAC ZBOX accomodates two DDR3 SO-DIMM memory modules. You must install at least one module in one of the two slots. Removing the memory module 1. Locate the SO-DIMM memory slot and gently press the two arms securing the memory module outwards, as shown in the image below, to release the memory module. 2. Remove the memory module from the slot at a 45-degree angle.
ZOTAC ZBOX Installing a hard disk 1. Locate the hard disk bracket and remove the thumb screw. 2. Lift up on the plastic flap. 3. Insert a 2.5-inch SATA hard disk into the bracket at a 45 degree angle and gently slide into the connector. 4. Lower the plastic flap and reinstall thumb screw.
ZOTAC ZBOX Setting up your ZOTAC ZBOX You need to connect peripherals before using your ZOTAC ZBOX. 1 2 3 4 5 6 7 8 5 1. Connecting a WiFi antenna module Connect a WiFi antenna module to the WiFi antenna connector. Note: When using the ZOTAC ZBOX, please be sure that the WiFi antenna module is connected to the WiFi antenna connector for the better performance of the WiFi/Bluetooth. 2. Connecting to USB 3.0 devices Connect USB 3.
ZOTAC ZBOX 5. Connecting to a DVI or VGA display Connect one end of a DVI/VGA cable to an HDTV or monitor, and the other end to the DVI port on the system rear panel. If using a VGA connection, please use included DVI-to-VGA adapter. 6. Connecting to an HDMI display Connect one end of an HDMI cable to the HDMI port on the system rear panel and the other end to a HDMI-compatible display such as an HDTV or monitor. 7.
ZOTAC ZBOX Positioning your ZOTAC ZBOX Do not position the ZOTAC ZBOX where the ventilation holes are covered. To guarantee proper use, leave 4 inches (10 cm) spacing in front of the ventilation holes. ZOTAC mini-PC system provide ample connectivities in tiny space, please choose connectors and cables in appropriate size to avoid interference. Installing the stand Erect your ZOTAC ZBOX with the supplied stand. To do so : 1. Locate the screw hole on the bottom of the ZOTAC ZBOX. 2.
ZOTAC ZBOX IR receiver Enjoy more of your favorite entertainment by MCE (Media Center Edition) remote controller with USB IR receiver (connecting to USB 2.0 port). External USB IR receiver Remote control ZOTAC ZBOX Giga is shipped with a remote control. Follow the instructions below to use the remote control. Function keys Playback Buttons OK START OK BACK UP DOWN LEFT RIGHT i Audio and Video Buttons + - VOLUME UP / DOWN MUTE STOP REW PLAY 1 4 7 *.
ZOTAC ZBOX Lithium cell installation 1. Locate the arrow on the rear cover of the remote control, and push the cover as the arrow direction. 2. Remove the rear cover, and insert the CR2032 lithium cells into the battery jar at a 45 degree angle. 3. Gently press down on the CR2032 lithium cells, and reinstall the rear cover.
ZOTAC ZBOX Installing drivers and software Installing an operating system The ZOTAC ZBOX does not ship with an operating system preinstalled. The user must install the operating system before the ZOTAC ZBOX can be used. The following operating systems are supported: • Windows 7 • Several Linux distributions Follow the instructions below to install an operating system: 1. Attach external DVD drive via USB 2.0 2. Insert disk for operating system (Windows or Linux). 3.
ZOTAC ZBOX Each driver must be installed individually to ensure proper operation of the 3. 4. 5. ZOTAC ZBOX. Select the driver you want to install. The driver installer should launch. Follow the onscreen instructions to install the drivers. Restart the system. Using your ZOTAC ZBOX Configuring wireless connection To connect to a wireless network, follow the instructions below: 1. Double-click the crossed wireless network icon (pic) on the notification area. 2.
ZOTAC ZBOX Using a dynamic IP (PPPoE connection) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Repeat Step 1-3 in the previous section. Select Obtain an IP address automatically and click OK. Click Create a new connection to start the NEW Connection Wizard. Click Next. Select Connect to the Internet and click Next. Select Set up my connection manually. Select your connection type and click Next. Enter your ISP Name and click Next. Enter your User name and Password. Click Next.
ZOTAC ZBOX 19
ZOTAC ZBOX 20 291-MA217-01
