ZOTAC ZBOX ZOTAC ZBOX User’s Manual No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ZOTAC.
ZOTAC ZBOX Table of Contents Product specifications-----------------------------------------------------------------------------------------3 Safety information-----------------------------------------------------------------------------------------------4 Setting up your system--------------------------------------------------------------------------------------4 Care during use-----------------------------------------------------------------------------------------------4 Welcome--------------------
ZOTAC ZBOX Product specifications q Microprocessor support v Intel Core i3-7100U (dual core 2.4 GHz) for ZBOX MI526 v Intel Core i5-7200U (dual core 2.5 GHz, up to 3.1 GHz) for ZBOX MI548 q Operating systems: v Windows 10 64-bit q System Memory support v Two 260-pin SO-DIMMs DDR4 up to 2133 Mbps v Up to 32 GB of memory q USB Ports v Two USB 3.1 Type-C port, one USB 3.0 port (from SD/USB 3.0 Combo) at front panel v Two USB 3.0 ports and one USB 2.0 port at rear panel, one USB 3.
ZOTAC ZBOX Safety information Your ZOTAC ZBOX is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system Read and follow all instructions in the documentation before operating your system. Do not use this product near water or a heat source such as a radiator. Set up the system on a stable surface with the provided stand.
ZOTAC ZBOX Welcome Congratulations on your purchase of the ZOTAC ZBOX. The following illustration displays the package contents of your new ZOTAC ZBOX. If any of the below items is damaged or missing, contact your retailer.
ZOTAC ZBOX Getting to know your ZOTAC ZBOX Front view 1 2 3 4 5 6 7 Refer to the diagram below to identify the components on the front of the ZBOX 1. Headphone/Audio Out jack The stereo headphone jack (3.5mm) is used to connect the system’s audio output signal to amplified speakers or headphones. 2. Microphone jack The microphone jack is designed to connect a microphone for video conferencing, voice narrations or simple audio recordings. 3. Combo USB 3.0 port / Memory card slot The Combo USB 3.
ZOTAC ZBOX Rear view 1 2 3 4 3 5 6 7 Refer to the diagram below to identify the components on the back of the system. 1. WiFi antenna connector The WiFi antenna connector supports the included WiFi antenna. 2. DisplayPort DisplayPort supports both external (box-to-box) and internal (laptop LCD panel) display connections. 3. Ethernet ports The eight-pin RJ-45 LAN port supports standard Ethernet cable for connections to local area networks (LAN) with speeds of 10/100/1000Mbps. 4. USB 2.
ZOTAC ZBOX How to disable the ring LED indicator 1. 2. 8 Turn on the ZBOX Mini PC and press to enter the BIOS SETUP UTILITY. Use the arrow keys to navigate to the Power menu and select Logo Indicator.
ZOTAC ZBOX 3. Press and select Turn off. 4. Press F10 to save the configuration and exit.
ZOTAC ZBOX Installing hardware inside the ZOTAC ZBOX Before installing hardware, please follow the instructions below to remove the cover of your ZOTAC ZBOX. 1. Remove the two rear thumb screws. 2. Gently remove the cover as shown below.
ZOTAC ZBOX Installing a memory module 1. Locate the SO-DIMM memory slots and insert a SO-DIMM memory module into the slot at a 45 degree angle. Note: When installing two SO-DIMM memory modules, please insert a module into the lower slot first. 2. Gently press down on the memory module until it locks into place by the arms of the memory slot. Note: This ZOTAC ZBOX accomodates two DDR4 SO-DIMM memory modules. You must install at least one module for the system to function.
ZOTAC ZBOX Removing a memory module 1. Locate the SO-DIMM memory slot and gently press the two arms securing the memory module outwards, as shown in the image below, to release the memory module. 2. Remove the memory module from the slot at a 45-degree angle.
ZOTAC ZBOX Installing a hard disk drive 1. Insert the hard disk drive into the slot at a 45 degree angle and gently slide into the connector. 2. Reinstall the screw.
ZOTAC ZBOX Setting up your ZOTAC ZBOX Please connect your peripherals before using your ZOTAC ZBOX.
ZOTAC ZBOX 1. Connecting the WiFi antenna Connect the WiFi antenna to the WiFi antenna connector. 2. Connecting a DisplayPort display Connect the DisplayPort connector to the DP port of the monitor or display. 3. Connecting to a network Connect one end of a network cable to the LAN port on the system rear panel and the other end to a network router, hub or switch. 4. Connecting to USB 2.0 devices Connect USB 2.0 devices such as keyboards, mice, cameras and hard disk drives. 5.
ZOTAC ZBOX Positioning your ZOTAC ZBOX Do not position the ZOTAC ZBOX where the ventilation holes are covered. To guarantee proper use, leave 4 inches (10 cm) spacing in front of the ventilation holes. ZOTAC Mini PC systems provide ample connectivity in a compact form factor, please choose connectors and cables in appropriate sizes to avoid interference. Installing the stand Position your ZOTAC ZBOX upright with the supplied stand. To do so : 1. Locate the key hole on the bottom of the ZOTAC ZBOX.
ZOTAC ZBOX Installing drivers and software Installing an operating system The ZOTAC ZBOX does not ship with an operating system preinstalled. The user must install the operating system before the ZOTAC ZBOX can be used. The following operating systems are supported: • Windows 10 64-bit Follow the instructions below to install an operating system: 1. Attach external DVD drive via USB 3.0 or 2.0 ports. Note: USB 3.1 Type-C ports do not support OS installation. 2.
ZOTAC ZBOX • HDA Sound Driver • Intel Graphics Driver • Ethernet PCI-E Driver • Intel Ethernet PCI-E Driver • Wireless Network Driver • Intel Management Engine • Bluetooth Driver • MassStorage Driver • Asmedia USB Controller • USB Charger (optional) Note: If you want to use high-amperage USB charging for smartphones and tablets, please install the driver USB Charger driver. Each driver must be installed individually to ensure proper operation of the ZOTAC ZBOX. 3. Select the driver you want to install.
ZOTAC ZBOX Configuring a wired connection Using a static IP 1. Right-click the network icon in the notification area and select “Open Network Connections”. 2. Right-click “Local Area Connection” and select “Properties”. 3. Highlight “Internet Protocol (TCP/IP)” and click “Properties”. 4. Select “Use the following IP address”. 5. Enter your IP address, subnet mask and Default gateway. 6. Enter the preferred DNS server address if necessary. 7.
ZOTAC ZBOX 10. Click “Finish” to finish the configuration. 11. Enter your user name and password. Click “Connect” to connect to the internet. Note: Contact your internet Service Provider (ISP) if you have problems connecting to the network. Configuring audio output Follow the steps below to enable audio output when connecting the ZOTAC ZBOX to a TV or receiver via DP/HDMI adapter. 1. Access the Sound settings via the system Control Panel. 2.