CDMA2000 1X EV-DO Wireless Data Terminal User Guide CDMA2000 1X EV-DO Wireless Data Terminal User Guide This User Guide is used for Wireless Data Terminal of AC2726. ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Copyright Statement Copyright © 2009 by ZTE Corporation All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. ZTE Corporation reserves the right to make modifications on print errors or update specifications in this manual without prior notice.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Table of Contents 1. Introduction ................................................................................................................................... 1 2. Precautions .................................................................................................................................... 1 3. Appearance................................................................................................................................
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 1. Introduction Thank you for choosing ZTE Corporation’s CDMA2000 Wireless Data Terminal (hereinafter referred to as Data Terminal). Data Terminal supports both CDMA2000 1X EV-DO and CDMA2000 1X network. In the area where there is signal, it allows you to go surfing on the Internet, send & receive short messages, and make & receive phone calls.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3. Appearance 3.1 Introduction Rear View Side View Cap USB Interface Back Cover Antenna Jack 3.2 Insert R-UIM Card Note: If your data terminal doesn’t need R-UIM card, please skip this section. 1. Pull out the tap; 2. Take out the R-UIM card cover in the direction indicated by the arrow; 3. Insert R-UIM card as below figure; 4. Push back R-UIM card cover. ZTE Corporation 2 http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3.3 Operation Guide of Data Cable Generally, the Data Terminal could be directly connected with USB port. You could also connect the Data Terminal with PC by using the accompanying data cable, as shown in the following figure. Connect Interface ① with Data Terminal, and interface ② with PC's USB port. If the power supply from USB port is insufficient, connect both interface ② and ③ with USB port together. 4. Install and Uninstall 4.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Note: Please connect the Data Terminal and PC with USB extension cable under weak signal to obtain the optimal performance. If necessary, adjust the Data Terminal's position. 4.2.2 Uninstall 1. Select Start All Programs ZTEMT want to remove the program. Click “Yes”. Uninstall ZTEMT UI, and you will be asked if you 2. Please wait and then click “OK” when un-installation is completed. 5.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide R-UIM card inserted indication Sleep indication Roaming indication Note: Some features like Voice Call, Call History, Short Message, and Phone Book may not be supported by your Data Terminal; the corresponding icons will not appear in the main window. 6. Connect/Disconnect Connect Click icon to set the relevant parameters. For details, please refer to 12 “Setting” for details. Click Click to enter the interface. .
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Note: The relevant information contained in connection records are just for user’s reference rather than the charging basis. Delete Connection Records Click button to delete the records you have selected on the interface. Clear Connection Records Click button to delete all the records. Note: If your data terminal doesn’t support Voice Call, Call History, Short Message, and Phone Book features, please skip 8-11 sections. 8.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Click button in the right side of the interface. Call Waiting During a call, you could select to answer the second incoming call, and then you could switch between the two incoming calls. Please firstly apply for this service from your local telecom operator. During a call, if there is a new incoming call; a pop-up window will prompt you that you have the second incoming call. If you select to answer, please click “Accept waiting call” button.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Click button to delete all records in Missed/ Accepted/Called catalog. Click button to dial the number. Click button to send a short message to this number. Click button to save this number to the phone book. Click button to clear the talk duration. Statistic 10. Short Message (If this feature is not supported by your Data Terminal, please skip over this chapter.) Click icon to enter Short message interface.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Click to forward this message to other recipients. Dial Sender’s Number Click to dial the sender’s phone number. Save Sender’s Number Click to save the sender’s number into phone book. Click to delete your selected records. Click to delete all the records in the inbox.. Click to copy your selected record into PC. Click to copy all the records from the data terminal to PC. Delete Clear Copy Copy All 11.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Delete All Click to delete all the contacts. Send messages from the phone book Click to compose the text. You could send the message to multiple recipients. Dial from the phone book Click to dial your selected phone number. Click to copy your selected contacts to other storage location. Click to copy all contacts to other storage location. Copy Copy All Import the call history Click to import the phone book (*.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide If your Data Terminal does not support some following functions, please neglect relevant description. Other Setting Click “Options” to switch the interface, and you could set URL and language, etc. If you want to use conference call, please select “Show 3 way call button during calling”; After the setting, click “Apply” button to save the settings on the current interface. Click “Change Password” button to set lock device.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 13. Help Click button to view the help file. Click “Help” button to view the relevant help file; click “Online service” to enter our company’s website. You could view the software version information under “About”. 14. Trouble-shooting Failures Causes Solutions Error occurs during the program Please download the program on our website The setup file may be damaged. WWW.ZTEMT.COM and reinstall it. installation. Open port failed.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide antenna is properly inserted. The The installation program can't auto set up. (If the Data Terminal supports auto setup function.) program has already been installed in current system. Firstly remove the original program and insert the terminal again.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.