CDMA2000 1X EV-DO Wireless Data Terminal User Guide CDMA2000 1X EV-DO Wireless Data Terminal User Guide This User Guide applies to Wireless Data Terminal of MG478 and AC8700.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Copyright Statement Copyright © 2006 by ZTE Corporation All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. ZTE Corporation reserves the right to make modifications on print errors or update specifications in this manual without prior notice. V1.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Table of Contents 1. 2. 3. 4. Introduction.............................................................................................................................1 Specification ...........................................................................................................................1 Precautions..............................................................................................................................
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 1. Introduction Thank you for choosing MG478/AC8700 CDMA2000 1X EV-DO Wireless Data Terminal (hereinafter referred to as Data Terminal) of ZTE Corporation. The Data Terminal equips with a standard USB interface and supports both CDMA2000 1X EV-DO and CDMA2000 1X network. In the area where there is signal, it allows you to go surfing on the Internet, browse the web pages, and send & receive Emails 2.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4. Appearance 4.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4.2 Insert R-UIM Card Note: If your data terminal doesn’t need R-UIM card, please skip this section. 1. Pull out the tap 2. Take out the R-UIM card cover in the direction indicated by the arrow 3. Insert R-UIM card as below figure 4.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 5. Install and Uninstall System Requirements: The Data Terminal supports the following operating system: ¾ Windows 2000 ¾ Windows XP PC minimum configurations: CPU Pentium-II/233MHz USB interface 2.0 (USB1.0 and 1.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 5.1 Windows 2000 5.1.1 Install Note: Do not insert the Data Terminal before installation. 1ǃFind “Setup.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3ǃSelect Start Menu folder, and then click “Next”; 4ǃWhen you see the window below, please click “Install”; 5ǃPlease wait for installation.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 6ǃPlease insert the Data Terminal into USB interface if the system prompts you to insert the hardware (If it has been inserted, please unplug it and insert again.) 7ǃThe system shall find the new hardware and install the driver automatically.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 8ǃThe driver is installed successfully. Pleas click “OK”; 9ǃClick “Finish” to close the last screen of the wizard. Now you can start the application for Data Terminal.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 5.1.2 Uninstall 1ǃSelect Start -> Programs -> ZTE EV-DO -> Uninstall ZTE EV-DO. Click “Uninstall ZTE EV-DO”, and you will be asked if you want to remove the program.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 5.2 Windows XP 5.2.1 Install Note: Do not insert the Data Terminal before installation. 1ǃFind “Setup.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3ǃSelect Start Menu folder, and then click “Next”; 4ǃWhen you see the window below, please click “Install”; 5ǃPlease wait for installation.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 6ǃPlease insert the Data Terminal into USB interface if the system prompts you to insert the hardware (If it has been inserted, please unplug it and insert again.) 7ǃThe system shall find the new hardware and install the driver automatically. Just wait a minute.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 8ǃThe driver is installed successfully. Pleas click “OK”; 9ǃClick “Finish” to close the last screen of the wizard.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 5.2.2 Uninstall 1ǃSelect Start -> Programs -> ZTE EV-DO -> Uninstall ZTE EV-DO. Click “Uninstall ZTE EV-DO”, and you will be asked if you want to remove the program. Click “Yes”; 2ǃPlease wait; 3ǃClick “OK” when un-installation is completed.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 6. Run the Application After the application is installed successfully, the application icon will appear on your desktop. Double-click this icon or select from Start -> Programs -> ZTE EV-DO -> ZTE EV-DO. Run the application to display the following user interface.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 7. Connect/Disconnect Connect Click icon to set the relevant parameters. For details, please refer to Chapter 9 “Setting” for details; icon at the left-up corner of the interface; Click After connecting to Internet, the current network information will appear on the interface. Double-click any place in the display area to view the connection records.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 8. Connection Records Click icon to view connection records. Connection records save the previous relevant information including Start at, Duration and Transmit bytes, which help you know the status easily. By switching among “List”, “Monthly” and “Statistic”, you could inquire the records every time, by month or by time. Note: The relevant information contained in connection records are just for user’s reference rather than the charging basis.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 9. Setting Network Connection Setting Click icon to set up the relevant parameters. After the setting, click “Apply” button to save the settings on the current interface. Click “Default” button and then “Apply” button to restore the settings on the current interface to factory default. Note: The default network setup parameters are as below.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Other Setting: Click “Options” to switch the interface, and you could set URL and select the skin, language, etc. After that, click “Apply” button to save the settings on the current interface . Click “Default” button and then “Apply” button to restore the settings on the current interface to factory default.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 10. Help Click button to view the help file. Click “Help” button to view the relevant help file; click “Online service” to enter our company’s website. You could view the software and its version information under “About”. 11. Connect to the Website Click button to directly connect the website you set. For details on the website setting, please refer to Chapter 9 “Setting”.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 12. Trouble-shooting After the installation, go to device manager and find “ZTE Status Interface 3197” under “Modem” and “ZTE USB Modem 3197” under “Port”. If they are not found, please remove the software and reinstall.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Common Failures Table: Failures Error occurs when Causes running setup.exe file. Open port failed. Solutions Please download the program on The setup file may be damaged. our website WWW.ZTEIT.COM and reinstall it. Directly run the software before the Close the software, plug in the Data Data Terminal is plugged in. Terminal and run it again.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide If the problems cannot be solved after the above handling, please call 86-755-2601555 or feed back your information directly by sending emails to zte_mobile@zte.com.cn for customer service. We will reply to you as soon as possible and provide you with high quality after-sales services. *SAR Information The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue.
