CDMA2000 1X EV-DO Wireless Data Terminal User Guide CDMA2000 1X EV-DO Wireless Data Terminal User Guide This User Guide is used for Wireless Data Terminal of AC8710. ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Copyright Statement Copyright © 2007 by ZTE Corporation All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. ZTE Corporation reserves the right to make modifications on print errors or update specifications in this manual without prior notice. V1.0, Nov.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Table of Contents 1. Introduction.............................................................................................................................1 2. Precautions..............................................................................................................................1 3. Appearance .............................................................................................................................2 3.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 1. Introduction Thank you for choosing AC8710 CDMA2000 1X EV-DO Wireless Data Terminal (hereinafter referred to as Data Terminal) of ZTE Corporation. The Data Terminal equips with a standard USB interface and supports both CDMA2000 1X EV-DO and CDMA2000 1X network. In the area where there is signal, it allows you to go surfing on the Internet, send&receive short messages, and make & receive phone calls. 2.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3. Appearance 3.1 Introduction Top View Rear View Tap USB Interface R-UIM Card Cover Antenna Host LED LED status descriptions: LED EV-DO 1X EV-DO 1X EV-DO 1X Yellow ON OFF Slow Flash OFF Quick Flash OFF Flash Green ON Slow Flash OFF OFF Flash OFF Network Registered Service available or Searching for the network Upon an incoming call(as the terminal supports voice call) Inserting the data terminal Quick Flash 3.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3. Insert R-UIM card as below figure； 4. Push back R-UIM card cover in the direction indicated by the arrow. 3.3 Operation Guide of Data Cable Generally, the Data Terminal could be directly connected with USB port. You could also connect the Data Terminal with PC by using the accompanying data cable, as shown in the following figure. Connect Interface ① with Data Terminal, and interface ② with PC's USB port.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4. Install and Uninstall System Requirements: The Data Terminal supports the following operating system: ¾ Windows 2000 ¾ Windows XP ¾ Windows Vista PC minimum configurations: CPU Pentium-II/233MHz USB interface 2.0 (USB1.0 and 1.1 compatible) Optical Drive CD-ROM (for installation only) Memory 64 MB Disk Space 50 MB (used for installation of application) ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4.1 Windows 2000 4.1.1 Install Note: Do not insert the Data Terminal before installation. 1、Find “Setup.exe” firstly in Data Terminal CD-ROM, double-click it to display the Welcome picture, and then click “Next”; 2、Select the location where you want the program to be installed, and then click “Next”; ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3、Select Start Menu folder, and then click “Next”; 4、When you see the window below, please click “Install”; 5、Please wait for installation. ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 6、Please insert the Data Terminal into USB interface if the system prompts you to insert the hardware (If it has been inserted, please unplug it and insert again.) 7、The system shall find the new hardware and install the driver automatically. Just wait a minute; ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 8、The driver is installed successfully. Pleas click “OK”; 9、Click “Finish” to close the last screen of the wizard. Now you can start the application for Data Terminal. ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4.1.2 Uninstall 1、Select Start -> Programs -> ZTE Wireless Terminal -> Uninstall ZTE Wireless Terminal. Click “Uninstall ZTE Wireless Terminal”, and you will be asked if you want to remove the program. Click “Yes”; 2、Please wait; 3、Click “OK” when un-installation is completed; ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4.2 Windows XP 4.2.1 Install Note: Do not insert the Data Terminal before installation. 1. Find “setup.exe” firstly in the Data Terminal CD-ROM, double-click it to display the Welcome picture, and then click “Next”; 2. Select the location where you want the program to be installed, and then click “Next”; ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3. Select Start Menu folder, and then click “Next”; 4. When you see the window below, please click “Install”; ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 5. Please wait for installation; 6. Please insert the Data Terminal into USB interface if the system prompts you to insert the hardware; (If it has been inserted, please unplug it and insert again.) ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 7. The system shall find the new hardware and install the driver automatically. Just wait a minute; ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 8. The driver is installed successfully. Pleas click “OK”; 9. Click “Finish” to close the last screen of the wizard. Now you can start the application for data terminal. ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4.2.2 Uninstall 1. Select Start Programs ZTE Wireless Terminal Uninstall ZTE Wireless Terminal. Click “Uninstall ZTE Wireless Terminal”, and you will be asked if you want to remove the program. Click “Yes”. 2. Please wait. 3. Click “OK” when un-installation is completed. ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4.3 Windows Vista 4.3.1 Install Note: Do not insert the Data Terminal before installation. 1、Find “Setup.exe” firstly in the Data Terminal CD-ROM, double-click it to display the Welcome picture, and then click “Next”; 2、Select the location where you want the program to be installed, and then click “Next”; ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3、Select Start Menu folder, and then click “Next”; 4、When you see the window below, please click “Install”; 5、Please wait for installation; ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 6、Please insert the Data Terminal into USB interface if the system prompts you to insert the hardware (If it has been inserted, please unplug it and insert again.) 7、The system shall find the new hardware and install the driver automatically. Just wait a minute.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 8、The driver is installed successfully. Pleas click “OK”; 9、Click “Finish” to close the last screen of the wizard. Now you can start the application for data terminal. ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4.3.2 Uninstall 1、Select Start -> All Programs -> ZTE Wireless Terminal -> Uninstall ZTE Wireless Terminal. Click “Uninstall ZTE Wireless Terminal”, and you will be asked if you want to remove the program. Click “Yes”; 2、Please wait; 3、Click “OK” when un-installation is completed. ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4.4 Manually Install Through Other USB Port If the data terminal doesn't work through other USB ports after the driver is installed successfully through a USB port, you could manually install the driver in the following method. Please make sure to quit other applications during the installation. 4.4.1 Windows 2000 Insert the data terminal to another port, and the system will find new hardware and automatically install the driver.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 5. Run the Application After the application is installed successfully, the application icon will appear on your desktop. Double-click this icon or select from Start -> Programs ->ZTE Wireless Terminal -> ZTE Wireless Terminal. Run the application to display the following user interface. Press to display other icons.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Status Bar: EV-DO indication Call indication 1X indication Missed call indication 1X/DO indication Unread message indication Signal strength indication. The more bars there are, the stronger signals are.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide “Setting” for details. Click After connecting to Internet, the current network information will appear on the interface. Double-click any place in the display area to view the connection drawing. icon at the left-up corner of the interface. Disconnect After connecting to Internet, click the rotating icon at the left-up corner of the interface. 7. Connection Records icon to view connection records.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Click button to delete all the records. Note: If your data terminal doesn’t support Voice Call, Call History, Short Message, and Phone Book features, please skip 8-11 sections. 8. Voice Call Click to enter voice call interface. Make a call Click the digits in the right side of the interface, or input the digits directly from keyboard.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Call Waiting During a call, you could select to answer the second incoming call, and then you could switch between the two incoming calls. Please firstly apply for this service from your local telecom operator. During a call, if there is a new incoming call, a pop-up window will prompt you that you have the second incoming call. If you select to answer, please click “Accept waiting call” button.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Three-way Call This function allows for the call among three parties. Please firstly apply for this service from your local telecom operator. Note: You need set “Show 3 way call button during calling”. Please perform the setting according to chapter 12. You could click “Dial second call” button during a call, input the third-party number in the pop-up window, and then press “OK” button to call the third party.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide During three-way conference call, click “Hangup second call” button to end the conference call, and return to the original call. 9. Call History Click icon to view the call history. The outgoing/incoming calls are saved in call history, including missed calls; incoming calls, outgoing calls, and talk duration. You could select the type you want to view. Missed/Accepted/Called Calls Click button to delete your selected record.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Click button to dial the number. Click button to send a short message to this number. Click button to save this number to the phone book. Click button to clear the talk duration. Statistic 10. Short Message Click icon to enter Short message interface. Send a Message Input the text to send，or click Input the recipient’s number or click button to select the preset message to send.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Click button to save the text into outbox. The received messages will be saved in the Data Terminal In-box. After the Data Terminal In-box is full, the system will automatically move the messages in the Data Terminal In-box to the PC In-box, and clean out the Data Terminal In-box.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Delete Click to delete your selected records. Click to delete all the records in the inbox. Click to copy your selected record into PC. Clear Copy Copy All Click to copy all the records from the data terminal to PC. 11. Phone Book to view the Phone book. You could select to save the contacts either in the data Click terminal、R-UIM Card or in the computer. Click the pull-down menu to select the storage location.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Click then input the contents and select “OK” to add a new contact. Click then modify the contents and select “OK” to modify the contact Modify information. Dial from the phone book Click to dial your selected phone number. Send messages from the phone book Click to compose the text. You could send the message to multiple recipients. Search for contacts Click to search for the contacts by name or number.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 12. Setting Click to enter the setting interface. Network Connection Setting Set up the relevant parameters, work mode on the “Network” interface. After the setting, click “Apply” button to save the settings on the current interface. Click “Default” button and then “Apply” button to restore the settings on the current interface to factory default. Note: The default network setup parameters are as below.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Other Setting: Click “Options” to switch the interface, and you could set URL and select the skin, language, etc. If you want to use conference call, please select “Show 3 way call button during calling”; After the setting, click “Apply” button to save the settings on the current interface. Click “Change Password” button to set lock device. The password is required when you start the application.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Select ring tone After clicking “Ring”, you could set different ring tones for Call coming, New message, Call connected, Call disconnected and Waiting call. After the setting, click “Apply” button to save the settings on the current interface. Click “Default” button and then “Apply” button to restore the settings on the current interface to factory default.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide After the setting, click button to send the corresponding request to the network system. After the setting, click “Apply” button to save the settings on the current interface. Click “Default” button and then “Apply” button to restore the settings on the current interface to factory default. 13. Help Click button to view the help file.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 15. Trouble-shooting After the installation, go to device manager and find “ZTE USB Modem FFFF” under “Modem” and “ZTE Service Port FFFF”, “ZTE Voice Port FFFF” under “Port”. If they are not found, please remove the software and reinstall. ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Common Failures Table: Failures Causes Error occurs when running setup.exe file. The setup file may be damaged. Directly run the software before the Data Terminal is plugged in. Open port failed. No R-UIM card. No signal indicated. The port is occupied by other applications, such as “Hyper terminal”, or the software is already run. R-UIM card is not inserted. R-UIM card is damaged. Validate by using a CDMA terminal. Replace R-UIM card.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Warning: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance will void the user’s authority to operate the equipment.
