CDMA2000 1X EV-DO Wireless Data Terminal User Guide CDMA2000 1X EV-DO Wireless Data Terminal User Guide This User Guide is used for Wireless Data Terminal of AC8710. ZTE Corporation http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Copyright Statement Copyright © 2009 by ZTE Corporation All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. ZTE Corporation reserves the right to make modifications on print errors or update specifications in this manual without prior notice.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Table of Contents 1. Introduction.............................................................................................................................1 2. Precautions..............................................................................................................................1 3. Appearance .............................................................................................................................2 3.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 1. Introduction Thank you for choosing AC8710 CDMA2000 1X EV-DO Wireless Data Terminal (hereinafter referred to as Data Terminal) of ZTE Corporation. The Data Terminal equips with a standard USB interface and supports both CDMA2000 1X EV-DO and CDMA2000 1X network. In the area where there is signal, it allows you to go surfing on the Internet, send& receive short messages, and make & receive phone calls.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3. Appearance 3.1 Introduction LED status descriptions: LED Inserting the data terminal Service available or Searching for the network Network Registered Upon an incoming call(as the terminal supports voice call) EV-DO 1X EV-DO 1X EV-DO 1X Yellow ON OFF Slow Flash OFF Quick Flash OFF Flash Green ON Slow Flash OFF Quick Flash OFF Flash OFF 3.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3. Insert R-UIM card as below figure; 4. Push back R-UIM card cover in the direction indicated by the arrow. 3.3 Operation Guide of Data Cable Generally, the Data Terminal could be directly connected with USB port. You could also connect the Data Terminal with PC by using the accompanying data cable, as shown in the following figure. Connect Interface ① with Data Terminal, and interface ② with PC's USB port.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4. Install and Uninstall 4.1 System Requirements The Data Terminal supports the following operating system: ¾ Windows 2000 ¾ Windows XP ¾ Windows Vista PC minimum configurations: CPU Pentium-II/233MHz USB interface 2.0 (USB1.0 and 1.1 compatible) Optical Drive CD-ROM (for installation only) Memory 64 MB Disk Space 50 MB (used for installation of application) 4.2 Installation Guide Take Windows XP for example.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3. Select Start Menu folder, and then click “Next”; 4. When you see the window below, please click “Install”; 5. Please wait for installation; ZTE Corporation 5 http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 6. Please insert the Data Terminal into USB interface if the system prompts you to insert the hardware; (If it has been inserted, please unplug it and insert again.) 7. The system shall find the new hardware and install the driver automatically. Just wait a minute; ZTE Corporation 6 http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 8. The driver is installed successfully. Pleas click “OK”; 9. Click “Finish” to close the last screen of the wizard. Now you can start the application for data terminal. ZTE Corporation 7 http://www.zte.com.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4.2.2 Uninstall 1. Select Start -> All Programs -> ZTE Wireless Terminal -> Uninstall ZTE Wireless Terminal. Click “Uninstall ZTE Wireless Terminal”, and you will be asked if you want to remove the program. Click “Yes”. 2. Please wait. 3. Click “OK” when un-installation is completed. 4.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide application for data terminal. 5. Run the Application After the application is installed successfully, the application icon will appear on your desktop. Double-click this icon or select from Start -> Programs ->ZTE Wireless Terminal -> ZTE Wireless Terminal. Run the application to display the following user interface. to display other icons.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Short Message Phone Book Connection Record Setting Help Status Bar: EV-DO indication Call indication 1X indication Missed call indication 1X/DO indication Unread message indication Signal strength indication. The more bars there are, the stronger signals are.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 6. Connect/Disconnect Connect Click icon to set the relevant parameters. For details, please refer to Chapter 12 “Setting” for details. Click icon at the left-up corner of the interface. After connecting to Internet, the current network information will appear on the interface. Double-click any place in the display area to view the connection drawing.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 7. Connection Records Click icon to view connection records. Connection records save the previous relevant information including Start at, Duration and Transmit bytes, which will help you know the status easily. By switching among “List”, “Monthly” and “Statistic”, you could inquire the records every time, by month or by time. Note: The relevant information contained in connection records are just for user’s reference rather than the charging basis.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 8. Voice Call to enter voice call interface. Click Make a call Click the digits in the right side of the interface, or input the digits directly from keyboard. Press button or press “Backspace” to delete the previous input digit; press button or press “Esc” to clear all the inputs. Click button in the right side of the interface or press “Enter” to make a call.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide between the two incoming calls. Please firstly apply for this service from your local telecom operator. During a call, if there is a new incoming call, a pop-up window will prompt you that you have the second incoming call. If you select to answer, please click “Accept waiting call” button. The previous call won’t be ended, but temporarily paused. You could switch between two incoming calls by clicking “Switch call”.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Three-way Call This function allows for the call among three parties. Please firstly apply for this service from your local telecom operator. Note: You need set “Show 3 way call button during calling”. Please perform the setting according to chapter 12. You could click “Dial second call” button during a call, input the third-party number in the pop-up window, and then press “OK” button to call the third party.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide During three-way conference call, click “Hangup second call” button to end the conference call, and return to the original call. 9. Call History icon to view the call history. The outgoing/incoming calls are saved in call history, Click including missed calls; incoming calls, outgoing calls, and talk duration. You could select the type you want to view. Missed/Accepted/Called Calls Click button to delete your selected record.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Click button to dial the number. Click button to send a short message to this number. Click button to save this number to the phone book. Click button to clear the talk duration. Statistic 10. Short Message icon to enter Short message interface. Click Send a Message Input the text to send,or click Input the recipient’s number or click book. Add more recipients if you like. Select priority.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide The received messages will be saved in the Data Terminal In-box. After the Data Terminal In-box is full, the system will automatically move the messages in the Data Terminal In-box to the PC In-box, and clean out the Data Terminal In-box. You could copy the messages from the Data Terminal In-box to PC In-box by selecting Copy or Copy All; you could also copy the messages from PC In-box to the Data Terminal In-box by selecting Copy.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 11. Phone Book Click to view the Phone book. You could select to save the contacts either in the PC(computer)、Normal(data terminal)、R-UIM Card(If your data terminal needs R-UIM card) or in the Emergent. Click the pull-down menu to select the storage location. Add Click then input the contents and select “OK” to add a new contact. Click then modify the contents and select “OK” to modify the contact Modify information.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Delete All Click to delete all the contacts. Click to copy your selected contacts to other storage location. Copy Copy All Click to copy all contacts to other storage location. 12. Setting Click to enter the setting interface. Network Connection Setting Set up the relevant parameters, work mode on the “Network” interface. After the setting, click “Apply” button to save the settings on the current interface.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Other Setting: Click “Options” to switch the interface, and you could set URL and select the skin, language, etc. If you want to use conference call, please select “Show 3 way call button during calling”; After the setting, click “Apply” button to save the settings on the current interface. Click “Change Password” button to set lock device. The password is required when you start the application.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Select ring tone After clicking “Ring”, you could set different ring tones for Call coming, New message, Call connected, Call disconnected and Waiting call. After the setting, click “Apply” button to save the settings on the current interface. Click “Default” button and then “Apply” button to restore the settings on the current interface to factory default.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 13. Help Click button to view the help file. Click “Help” button to view the relevant help file; click “Online service” to enter our company’s website. You could view the software version information under “About”. 14. Connect to the Website Click button to directly connect the website you set. For details on the website setting, please refer to Chapter 12 “Setting”. 15.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Common Failures Table: Failures Causes Error occurs during the The setup file may Please program installation. be damaged. WWW.ZTEMT.COM and reinstall it. Directly run Solutions download the program on our website the software before the Close the software, plug in the Data Terminal and run it Data Terminal is again. plugged in. The Open port failed.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide connected to the Access Box. Out of the network service area. Make sure it is in the CDMA network service area. The antenna or RF component is Replace relevant damaged parts. damaged. Wrong setting of Correct the parameter settings. Consult your service provider parameters. (Phone, User, for details. Password.) Dialing failed. Not enough money. Consult your service provider for details. Network congestion or Try again later. failure.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide program is installed successfully. The program is not yet installed, and no other previous version installed was in the Please restart your computer. Please contact your local operator or product technical support center if CD-ROM disk ordinal doesn't appear after your computer is restarted. system.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 16. FCC Regulations z This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. z This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID: Q78-AC8710.