ZTE A7020 Quick Start Guide 1
LEGAL INFORMATION Copyright © 2020 ZTE CORPORATION. All rights reserved. No part of this publication may be quoted, reproduced, translated or used in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. Notice ZTE Corporation reserves the right to make modifications on print errors or update specifications in this guide without prior notice. We offer self‐service for our smart terminal device users.
Getting to Know Your Phone Proximity & light sensor Earpiece Indicator light Front camera nano‐SIM/ microSDXC card tray Volume key Power key Touch screen Headset jack Back cameras and flash Fingerprint sensor Charging/USB Type‐C jack Speaker 3
Setting Up Your Phone The nano‐SIM card can be installed or removed while the phone is turned on. WARNING! To avoid damage to the phone, do not use any other kind of SIM cards, or any non‐standard nano‐SIM card cut from a SIM card. You can get a standard nano‐SIM card from your service provider. 1. Insert the tip of the tray eject tool into the hole on the card tray. CAUTION: Never replace the included tray eject tool with sharp objects. Ensure that the tray eject tool is perpendicular to the hole.
microSDXC card nano‐SIM card Charging the Phone Your phone’s battery should have enough power for the phone to turn on, find a signal, and make a few calls. You should fully charge the battery as soon as possible. WARNING! Use only ZTE‐approved chargers and USB Type‐C cables. The use of unapproved accessories could damage your phone or cause the battery to explode. WARNING! Do not remove the back cover. The battery is not removable. Removal may cause fire or explosion. 1.
2. Connect the charger to a standard AC power outlet. 3. Disconnect the charger when the battery is fully charged. NOTE: If the battery is extremely low, you may be unable to power on the phone even when it is being charged. In this case, try again after charging the phone for at least 20 minutes. Contact the customer service if you still cannot power on the phone after prolonged charging. Powering On/Off Your Phone Make sure the battery is charged before powering on.
FM Radio Scanning for Channels 1. Plug in a wired headset and open FM Radio. 2. Touch > Scan. Your phone scans for all available channels and saves them to the channel list. Listening to FM Radio 1. Open FM Radio while the headset is connected. 2. Touch > All channels and select a channel. You can also drag the red line along the frequency panel or touch or to switch to other channels, or touch or to adjust the current channel frequency. NOTES: Touch to add the channel to favorites.
Product Safety Information Don’t make or receive phone calls while driving. Never text while driving. Keep your phone at least 10 mm away from your body while making calls. Small parts may cause choking. Your phone can produce a loud sound. To prevent possible hearing damage, do not listen at high volume levels for long periods. Exercise caution when holding your phone near your ear while the loudspeaker is in use. Avoid contact with anything magnetic.
Only use approved accessories. For pluggable equipment, the socket‐outlet shall be installed near the equipment and shall be easily accessible. Don’t rely on your phone as a primary device for emergency communications. FCC RF Exposure Information (SAR) This phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States.
can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: SRQ‐ZTEA7020. The FCC ID also can be found on the device when you open Settings > About phone > FCC ID. For this device, the highest reported SAR value for usage against the head is 0.703 W/kg, and for usage near the body is 1.306 W/kg. While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirements.
§ 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
