GSM Dual-Band GPRS Digital Mobile Phone User Manual The manual is applicable for N280 mobile phone.
FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Health and safety information The phone with internal antenna has been tested for compliance with FCC RF Exposure (SAR) limits and is complied with FCC RF exposure compliance requirements. Exposure to radio frequency energy Radio wave exposure and Specific Absorption Rate (SAR) information The handset is designed to comply with safely, requirements for exposure to radio waves.
Legal Information Copyright © 2009 by ZTE CORPORATION All Rights Reserved Your mobile phone is made by ZTE CORPORATION. No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of ZTE CORPORATION. Trademarks ZTE and the ZTE logos are trademarks of ZTE CORPORATION. Notice The information in this manual is subject to change without notice.
Contents 1 Basic Information ....................................................................................................................................................................... 5 1.1 Brief Introduction ............................................................................................................................................................. 9 1.2 Safety Instruction ...........................................................................................................
2.6.7 Dial calls 17 2.6.8 Dial domestic calls 17 2.6.9 Dial extensions of fixed phones 17 2.6.10 Dial international calls 17 2.6.11 Dial Call in the List 17 2.6.12 Emergency Calls 18 2.6.13 Answer Calls 18 2.6.14 Call Register 18 2.6.15 Call Menu 18 3 Function Menu ......................................................................................................................................................................... 20 3.1 Use of Function Menu ................................................
3.10.2 Phone Settings 29 3.10.3 Call Settings 31 3.10.4 Single-Card Settings 32 3.10.5 Network Settings 32 3.10.6 Security Settings 32 3.10.7 Restore Factory Settings 33 3.10.8 Sound Effect 33 3.11 Multimedia..................................................................................................................................................................... 33 3.11.1 TV 33 3.11.2 Functions of TV 3.11.3 Camera 33 3.11.4 Album 34 3.11.5 Video Camera 34 3.11.6 Video Player 34 3.11.
3.15 Toolbox........................................................................................................................................................................... 39 3.15.1 Calendar 39 3.15.2 Memo 40 3.15.3 Alarm Clock 40 3.15.4 World Time 40 3.15.5 Incoming Call Show 40 3.15.6 Stopwatch 40 3.16 Network Service ............................................................................................................................................................ 41 3.16.
1 Basic Information 1.1 Brief Introduction Thank you for selecting our GSM/GPRS digital mobile phone. You can fully understand the usage of this phone and enjoy the sound functions and simple operation way after reading this manual. This color screen mobile phone is designed for GSM/GPRS network environment.
Do not put the phone to places with high temperature, high humidity or heavy dust, or else, it can cause malfunction. Please keep the phone out of the reach of children to avoid personal injury as children may consider it as toy. Do not put the phone on uneven or unsteady platform, or it may drop and cause failure or damage. 1.3.
overheat, explosion and fire. Once there’re abnormal phenomena, like temperature increasing, color change, distortion during the usage, charging or save of the battery, please stop using and replace with new battery. It may burn the skin once the liquid from battery touches skin or clothes, please flush with plenty of clean water immediately and go to hospital at once if necessary. Please take the battery away from the fire to avoid fire and explosion once the battery leaks or emits strange smell.
Battery: Place the battery in cool and ventilated place without direct sunlight. The battery has a limited lifetime. The use time of battery will be shortened progressively due to frequent charging. Once the battery is out of use after several charging, it means that the lifetime of the battery is over, and you shall replace it with approved model new battery. Do not dispose old battery as household waste.
Represents that you can use GPRS service. Enable vibration function. Receive new SMS. Receive new MMS. Alarm clock is set to On. It appears when headset is inserted. Enable call transfer function. Keypad isn’t unlocked. Keypad locked. Indicates battery level. Indicates missed calls.
number records under standby status. 5. Right Soft Key: It’s used to perform functions displayed in lower right corner on the screen. 6. Left Soft Key: It’s used to perform functions displayed in lower left corner on the screen. 7. End Key: It’s used to end calls or reject incoming calls. Press this key to return to standby status under other conditions. 8. TV key :when the player is runing , press this key enter TV interface 9.
Insert the end of the charger into the right side of the phone (Note: the arrowhead shall be upward). Then, power indication icon on the screen flashes repeatedly. If the phone is switched off during charging, there is power indication image on the screen, which means that the battery is under charging. If the phone is overused under low battery, then charging indication icon will be displayed after the charging has been done for some time.
Once you need to remove the SIM card, please switch off the phone first, disassemble the battery and remove the SIM card from SIM card holder. 2.6.3 Power On and Power Off Long press End Key to switch on the phone, and long press End Key to switch off the phone. If you switch on the phone and there’s no SIM card, the phone will prompt you to insert SIM card. The phone will check if the SIM card is available after SIM card is inserted.
Note: If EMERGENCY is displayed on the screen, it means that your phone is out of the normal network coverage, but you can also make emergency calls according to the signal strength. 2.6.7 Dial calls You’re allowed to make calls or answer incoming calls once name of network supplier appears on the screen. The signal bar in upper left corner represents the strength of network signal. Moving in a small range can improve your calling quality as the calling can be interfered by barriers greatly. 2.6.
placed on the top of the list (Please refer to Section 3.9 Call Register). Every phone number is classified based on Dialed Calls, Received Calls and Missed Calls. The phone also provides you with All Phone Items for you to view all calling record. Old phone numbers will be deleted automatically once the phone number list is full Please follow steps below to view the list: Press Dial Key to view dialed calls records; All phone numbers in the list can be dialed through Dial Key.
Record call voice. Quiet / Restore Do not send (or send) local voice. Dual Tone Multi Frequency Press Left Soft Key to open or close dual tone multi frequency. Handsfree Enable loudspeaker to amplify call voice. (Note: For the operations above, card B doesn’t support Pause / New Call / Audio Recording functions.) You can perform following operations if there’s incoming call in card B at the same time: Answer Card A and Reject Card B End card B and only answer card A.
3 Function Menu (※ Some part functions below depends on the function support status of specific phones) 3.1 Use of Function Menu Scroll to select functions Select to enter main function menu under standby status; Press keys or click touch screen to follow prompts to enter or exit from menu under main menu or submenu. Exit from menu Generally, you can exit from some menu items by pressing Right Soft Key.
4-2 Phone Settings 4-2-1 Time and Date 4-2-2 Auto Power On /Off 4-2-3 Language 4-2-4 Preset Input Method 4-2-5Standby Menu Display 4-2-6 Welcome Note 4-2-7 Speed Dial 4-2-8 Specify Function Key 4-2-9 Auto-update of Time 4-2-10 Flight Mode 4-2-11 Handwriting Settings 4-2-12 Other Settings 4-2-13 Power Saving Mode 4-4 Single-Card Settings 4-4-1 Auto Turning on Card 4-4-2 Turn on/off Card 4-3 Call Settings 4-3-1 My Phone Number 4-3-2 Call Waiting* 4-3-3 Call Transfer 4-3-4 *Call Barring 4-3-5 Line Switch 4-3-
5-8 FM Radio 5-9 Custom Ring 5-10 E-book 6 File Management 7 Entertainment and Game 7-1 Entertainment Bible 7-2 Mobile Phone QQ 7-3 Game Player Simulator 7-4 Subject 8 Profiles 9 Toolbox 8-1 General 9-1 Stock Manager 8-2 Meeting 9-2 Memo 8-3 Outdoor 9-3 Alarm Clock 8-4 Indoor 9-4 World Time 8-5 Earphone 9-5 Incoming Call Show 8-6 Bluetooth 9-6 Stopwatch 10 Network Service 10-1 *STK Service (It has something to do with network operator) 10-2 *Finger Tip Music* 10-3 WAP 10-4 Account Information 11 Additional
window, and you can input the relative information here to take the screening of the phone records. The searching ways available for selection: 1. Pinyin; 2. Stroke; 3. English 4. Number. ■ Name Search: Find record by name in the phonebook. ■ Add Number: Add a new phone record in the phonebook, and you can select the storage way to SIM card or the phone. There is little differentiation in the storage format for SIM card and the phone.
3.4.2 Create Message SMS network service allows you to send the text message to the other phones that can receive message. Please confirm that you have set the Short Messaging Service Center Number before creating message (please see “Message Settings”). Enter Create Message sub-menu to input SMS (please see chapter 4.2 “Instructions on Input Method”). - Finish: Selecting this option indicates that this message has been inputted completely, and it can enter the operation of the next step.
- Edit: Extract the content of the SMS, and enter the edit box. Forward: Forward this SMS. Copy to Phone (Copy to SIM Card): Copy the current SMS on SIM card (or the phone) to the phone (or SIM card) to store. - Move to Phone (Move to SIM Card): Move the current SMS on SIM card (or the phone) to the phone (or SIM card) to store. - Chat: Enter the chat room to chat by SMS. - Delete All: Delete all the SMS in the inbox. - Copy All: There are two available copy ways of From SIM Card and From Phone.
settings for the corresponding name, Short Messaging Service Center Number, effective term and sending format. Status Setting: Set whether to turn on the message report or reply path. Capacity Inquiry: View the space occupying state of the mailbox in SIM card or the phone. Storage Location: Select the phone or SIM card. Message Transmission Setting: The selections for the SMS transmission ways: GPRS Priority, GSM Priority and Only Use GSM.
Draft Box: It can save the edited but not sent MMS here. - View: View the content of the current MMS. - Message Details: View the details of the current MMS. - Edit: Edit the current MMS. - Send: Send the current MMS. - Delete: Delete the current MMS. - Delete All: Delete all the contents in the draft box. Sent items: Save the messages that have been sent successfully. - View: View the sent MMS. - Message Details: View the details of the current MMS. - Forward: Forward the current MMS to others.
3.8 Cell Broadcast Note: This function is not supported by card B. ■ Receiving Way: Select to turn on the receiving mode, and turn off rejecting receiving the messages of the cell broadcast. ■ Read Message: Enter this menu to read your tailored cell broadcast message. ■ Language: Set the language in receiving cell broadcast. ■ Channel Setting: Set the channel of the cell broadcast. Note: The services for the cell broadcast and the voice mailbox are provided by the operator, please contact your operator. 3.
Last Call Duration View the duration value of the last call. Dialed Calls’ Duration View the total duration value of the dialed calls. Received Calls’ Duration View the total duration value of the received calls. Clear Timers Clear the data in the timing statistics, and start to time again. ■ Call Costs It can store the accumulated cost of the calls by Call Costs. Last Call Cost Enter the Last Call Cost sub-menu, and view the last call cost.
- Time/Date Settings: Set the current time and date. - Format Settings: Set the display format of the time and date, 12-hour or 24-hour. Auto Power On/Off: Set the time, and the phone will switch on or off automatically when reaching to the set time. Language: Set the language in displaying the phone menus. Preset Input Method: Select a default input method. Standby Menu Display: - Wallpaper: Select the wallpaper of the standby interface.
3.10.3 Call Settings Phone Number Note: This function is not supported by card B. - System Preset: Whether the number sending uses the system default value. - Hide Number: The other party will not see the number when you calling. (Needed to be supported by the operator) - Send Number: The other party can see the number when you calling. Call Waiting: Note: This function is not supported by card B. Turn on or off the call waiting function. Select View to view the current call waiting status.
Auto Redial Note: This function is not supported by card B. The phone will redial automatically for every unsuccessful calling after turning on Auto Redial. Turn off Group: Turn off the group function. IP Dial: Set and turn on this item, and it can realize the IP dial function by the number records in the phone book. Blacklist: The numbers listed in the blacklist will be shielded. Note: Some functions need to be supported by the network operator. 3.10.
Phone Lock The phone lock can prevent your mobile phone used by the other without your permission. Select Phone Lock to turn on the phone password protection, and the phone will ask you the phone password when switching on next time; press it again to turn off the phone password protection. Note: The default phone lock password is 1122, and you shall change it to your own password as soon as possible. Keypad Lock: Set the waiting time of the keypad lock.
also enter the settings of the relative items by option. Enter the following by option: To Album: Enter the album. Camera Settings: Settings for some relative parameters on shooting Scence Switch: Switch between scene 1 and scene 2. Photo Settings: Settings of photo size and photo quality. White Balance: It can set the color of the illumination for the photo. Profile Mode: It can set the shooting mode. Special Effect Settings: Set the style of view finding. Frame: Select a picture box for the photo.
Rename: Change the name of the currently selected file. Delete: Delete the currently selected file. Delete All Files: Delete all the current archives. Sorting: Sort the archives (by name, type, time, size or no). Storage Path: View the storage location of the file (can be stored into the phone or the memory card). Note: The default file name of the video player is Video (the phone or the memory card). 3.11.7 Music Player Select Music Player to enter the mp3 play interface.
3.11.8 Audio Recording Select this option to take audio recording. Select the following options to enter: Audio Recording: Record a new voice. Play: Play the currently selected audio recording. Annex: Annex a new audio recording on the base of the original not audio recording. Rename: Change the name of the current audio recording file. Delete: Delete the current audio recording file. Delete All: Delete all the audio recording files. Settings: Set the audio recording format.
3.11.10 Custom Ring Select Add to enter the ring edit interface, press the number keys to edit ring, and it can also click Insert on the soft keypad to insert the music notation, click Edit to edit the ring, and click Play to listen the edited ring. Click Option in the custom ring edit interface to enter the settings of Play, Play Speed, Select Instrument and Storage. Noun Explanation: Play: Play the currently edited bass. Play Speed: Select the speed when playing (Fast, General and Slow).
Create Material Folder: Create the new material folder in the folder. Formatting: Format this folder. 3.13 Entertainment and Game Entertainment Bible: This item provides the relative value-added services. For the detailed information of this function, please contact the network operator. Mobile Phone QQ: The operations are the same as those for Tencent QQ. Game Player Simulator: This phone supports the simulating game, and this function can be operated by the handle.
Game Settings: Game Sound Effect: Turn it on or off. Game Vibration: Turn it on or off. Subject: Three background colors available for selection: Amber Orange, Sapphire and Techno-gray. When moving the selection bar to the appropriate menu, and you can preview it. Enter the following options: On: Apply the selected background color. Update Frequency: It will use the several background colors in turn within the corresponding time after being set frequency.
directly can also realize this function. Enter the following sub-menus by option: ■ Schedule: Create a schedule. Add an alarm remind for it. You can select any one from the five options of Once, Everyday, Custom, Every week and Every month. Once: Indicate that this schedule will be reminded once. Everyday: Indicate that this schedule will be reminded at the set moment every day. Custom: Set the ringing time of the alarm clock within one week.
right arrow keys respectively. Note: Method for clearing stopwatch: First pause the running stopwatch, long press the left key, and it can clear it to zero; 3.16 Network Service 3.16.1 STK Service Note: Card B doesn’t support this function. This function including brand value-added service of Monternet, M-zone and global surf is supplied by network supplier. This function can’t be used if the SIM card and the network supplier don’t support this service.
Select one account to enter: 1. Name: the name of this account. You can select edit to change it. 2. Number: the number of this account. 3. User account: the account of dial dial-up server not WAP gateway. 4. Password: the password of dial-up server not WAP gateway. 5. Line: select line type by analog or figure. 6. Speed: select proper transmission speed. 7. Network domain: IP address. GPRS data: Select one account to enter: 1. Name: the name of the account. You can select edit to change it. 2.
3.17.3 Exchange Rate Conversion To carry put exchange rate conversion, you should input exchange rate first and then input native or foreign monetary value and press left soft key to confirm, then the value you want will be displayed in another edit box. 3.17.4 Bluetooth - Activate blue tooth: You can activate or close blue tooth function through this switch. - Search handsfree device: the phone can automatically search handsfree devices with this function.
4 Input Method Instruction This phone supports Chinese simplified input method. The input methods supplied to you include English input method (capital case and lower case letter), number input method, Pinyin input method, smart Pinyin, stroke input and punctuation mark (common punctuation marks) input method. The functions permit to input characters in the phone are: inputting and editing SMS; inputting and editing names in phone book. looking for the name of telephone number.
Up arrow key Down arrow key Used to page up the screen or select Pinyin. Used to page down the screen or select Pinyin. Left arrow key Used to roll left or select Pinyin. Right arrow key Used to roll right or select Pinyin. Left soft key Confirm Right soft key Back End up key Back to standby interface General operation order of Pinyin input method: Input Pinyin letter: Input Pinyin letter by numeric keys from 1 to 9 Select Pinyin: select Pinyin by arrow key.
Numerical key 5 Hengzhe Numerical key 6 Huzhe Numerical key 7 Nizhe The last Zhe shall be referred to for multi Zhes, please see attached figure. The last Zhe shall be referred to for multi Zhes, please see attached figure. The last Zhe shall be referred to for multi Zhes, please see attached figure. Numerical key 8 The strokes that can’t be confirmed Numerical key 9 Hengshuzhe 乙 * key Used to call out symbols. # key Used to switch input methods.
4.2.3 English and Number Input The detailed definitions of the keypad at stroke input method are: Name Corresponding character or function Numerical key 1 .
5. T-flash card Introduction This phone supports the storage function of T-Flash card and its expanded storage function space. The detailed operations are as follows: 5.1 Takedown and installation of T-flash card T-flash card in this phone is under the battery. Insert it as the mark on it. Please open the card buckle first before pulling out the cared then take T-flash card out. Note: this phone supports plug & play function.
Common fault Poor reception Reason Using phone in poor reception area such as the vicinity of high-rise buildings or basement where the radio wave can’t reach. Using phone in the time of dense communication such as work began time and closing time when the line is in congestion and results in failure of communication. It may be resulted by the distance with network emission base station. Echo or noise It is resulted by poor network trunk line, which is a territorial problem.
It can’t be charged. The battery or charger is damaged. Change new battery or charger. It is charged in the environment with temperature Change charge environment. lower than -10℃ or higher than 55℃. It is not contacted well. Check whether the plug is connected correctly. New name can’t be The phone book is full. Delete some records in the phone book. added in the phone book. Some function Your network supplier doesn’t support this function or Please contact your network supplier.
