AT Command User Manual MC2261 AT Command User Manual Version:V1.
AT Command User Manual Update History Version Update section Type of Revision author Release Date V1.0 Luxiaofeng 08/17/2010 V1.1 Luxiaofeng 09/03/2010 V1.2 Zxw 10/14/2010 V1.3 QCMIPGETP QCMIPMHSSX zxw Bak 1:The update history is added after this document is update. Bak 2:This version only support sprint at command.
AT Command User Manual Table of Contents Table of Contents ............................................ 2 1 ZTE AT Commands ......................................... 5 1.1 SMS Text Mode Command ..................................................................................................... 5 1.1.1 +CPMS: Preferred Message Storage ............................................................................... 5 1.1.2 +CNMI: New Message Indications to TE ................................................
AT Command User Manual 3.1.13 3.1.14 3.1.15 3.1.16 3.1.17 3.1.18 3.1.19 3.1.20 +CBIP: IP address of the base station............................................................................ 23 +CSS: The serving system band and SID ...................................................................... 23 +CSQ: Signal Quality Measure and the Frame Error Rate............................................ 24 +CTA: The packet data inactivity timer ...............................................................
AT Command User Manual 5.3 5.4 5.5 5.6 5.2.7 +HFAR: SUCCESS the success sign of HFA session ................................................... 39 5.2.8 +HFAR: FAIL the fail sign of HFA session ................................................................... 39 5.2.9 +DCR: START the start sign of DC session .................................................................. 40 5.2.10 +DCR: SUCCESS the success sign of DC session ....................................................... 40 5.2.
AT Command User Manual 1 ZTE AT Commands 1.1 SMS Text Mode Command 1.1.
AT Command User Manual +CNMI: ,,,, OK +CNMI: (list of supported AT+CNMI=？ s),(list of supported s),(list of supported s),(list of supported s),(list of supported s) OK : set the message notice method (currently support mode=1). 0: cache the message notice in ME. If ME‟s cache memory is full, new notice will cover the older one 1: directly send the message notice to TE.
AT Command User Manual and are used to set new message alert（including +CMTI, +ZCMT, +CDSI, +ZCDS） is used to set directly report to TE or save in MT and report the storage location when receiving new message do not use it temporarily is used to set whether or not report SMS status report(+CDSI, +ZCDS) Default: +CNMI=1,1,0,2,0 1.1.
AT Command User Manual parameter : the messages storage location. 0: (or default) delete the messages designated by .
AT Command User Manual parameter value of character string, indicating the type of full storage memory “ME”: indicating NV example +ZSMMEMFULL: “ME” 1.2.
AT Command User Manual : Privacy level, refer to +ZCMGR to take the value : type of message, refer to +ZCMGR to take the value : value of integral number, SMS status, refer to +ZCMGR to take the value : received SMS. Control characters : indicating the ending of one message, character: '0x1A'(Unicode: '0x001A') : cancel the sending of the message，character: '0x1B'(Unicode: '0x001B') 1.2.4 +ZCMGS: Send Message description Send a message to network side.
AT Command User Manual example character to be transmitted is „0x4E00„ 7: Other coding method 0: no ack 1: need ack value of integral type, indicating the priority level of the message, take the value as below: 0: Normal 1: Interactive 2: Urgent 3: Emergency : message symbol : message date : indicating the ending of one message. Under non-UNICOD:'0x1A'; under UNICOD:'0x001A' : Cancel the sending of the message.
AT Command User Manual 1: TELEPHONY value of integral type, indicating the storage status of SMS, take the value as below: 0: received unread messages 1: received read messages 2: saved unsent messages 3: saved sent messages 4: all messages (the value is only applicable for +CMGL command) language take the value as below: 0: UNSPECIFIED 1: ENGLISH 2: FRENCH 3: SPANISH 4: JAPANESE 5: KOREAN 6: CHINESE 7: HEBREW value of integral type, indicating the priority level of the message, take th
AT Command User Manual 0: Normal 1: CPT (Optional) 2: Voice Mail 3: SMS Report : message text : command ending mark, indicating the ending of one command. : indicating the ending of one message. Under non-UNICOD:'0x1A', and under UNICOD:'0x001A' : Cancel the sending of the message. Under non-UNICOD:'0x1B', and under UNICOD:'0x001B' 1.2.
AT Command User Manual format AT+ZCMGR=[,] Under text mode, the command is successfully executed: +ZCMGR: ,,,,, ,,,, ,,,, OK otherwise: +CMS ERROR: AT+ZCMGR=? OK : value of integral type, location in memory : SMS status modifying mode 0: change to READ status 1: don‟t change the status : number of message sen
AT Command User Manual parameter the message‟s mark, take a decimal from 0~9, and the value ranges from 0~65535. 1.2.
AT Command User Manual 106 WMS_USER_DATA_SIZE_ERROR_S 107 WMS_OTHER_GENERAL_PROBLEMS_S 108 WMS_OTHER_GENERAL_PROBLEMS_MORE_FIRST_S 109 WMS_OTHER_GENERAL_PROBLEMS_MORE_LAST_S 2 Basic AT Commands 2.1.
AT Command User Manual ATV1 OK CE MUST support the parameter V0 which will cause the device to return result codes as numbers note CE MUST support the parameter V1 which will cause the device to return result codes as words CE MUST set the V parameter to V1 as default 2.1.
AT Command User Manual note AT&D1 OK AT&D2 OK CE MUST support the parameter &D0 (Data Terminal Ready) which will ignore circuit 108/2 (CD) Note: Circuit 108 is generally used for serial communications. Most Sprint devices use the USB interface and this is not required for general use of the device.
AT Command User Manual format AT+GMM example AT+GMM +GMM: OK +GMM: MC2716 OK CE MUST support “AT+GMM” which will return the device model name note and number as defined by the OEM and approved by Sprint on a single line CE MUST return “ERROR” for any other AT+GMM string 3.1.
AT Command User Manual +ICF: (list of supported < format >s),( list of supported < parity >s) OK AT+ICF=? parameter 0: Auto Detect 1: 8 Data 2 Stop 2: 8 Data 1 Parity 1 Stop 3: 8 Data 1 Stop 4: 7 Data 2 Stop 5: 7 Data 1 Parity 1 Stop 6: 7 Data 0: Odd 1: Even 2: Mark 3: Space AT+ICF=0,0 AT+ICF? OK +ICF: 2,2 AT+ICF=? OK +ICF: (0-6),(0-3) example OK CE MUST support “AT+ICF=,” which will set the character framing between the device and a
AT Command User Manual parameter 0: None 2: Circuit 133 (Ready for Receiving) 0: None 2: Circuit 106 (Clear to Send/Ready for Sending) AT+IFC=0,0 OK AT+IFC? +IFC: 2,2 example OK +IFC: (0,2),(0,2) AT+IFC=? OK CE MUST set the default value of IFC to none for DCE_by_DTE and note DTE_by_DCE CE MUST return “ERROR” for any other AT+IFC string 3.1.
AT Command User Manual parameter 0: no service is available 1: CDMA Digital service available 2: TDMA Digital service available 3: Analog service is available AT+CAD? +CAD: 0 example OK note CE MUST return “ERROR” for any other AT+CAD string. 3.1.
AT Command User Manual parameter
the IP address will be the IP address assigned by the network in PPP IPCP for SIP or in the MIP Registration Reply for Mobile IP AT+CMIP? 0.0.0.0 example OK CE MUST return “0.0.0.0” for “AT+CMIP?” if there is currently no IP note session established CE MUST return “ERROR” for any other AT+CMIP string 3.1.AT Command User Manual AT+CSS? +CSS: 1000,C,0 example OK note CE MUST return “ERROR” for any other AT+CSS string 3.1.15 +CSQ: Signal Quality Measure and the Frame Error Rate description Signal Quality Measure and the Frame Error Rate +CSQ: , format AT+CSQ? OK the measured RSSI value 0: less than 0.01% 1: 0.01% to less than 0.1% 2: 0.1% to less than 1.0% parameter 3: 0.5% to less than 1.0% 4: 1.0% to less than 2.0% 5: 2.0% to less than 4.0% 6: 4.
AT Command User Manual format +CPS: OK +CPS: 1 AT+CPS? AT+CPS? example OK CE MUST not support “AT+CPS =” note CE MUST return “ERROR” for any other AT+CPS string 3.1.
AT Command User Manual CE MUST set the packet call state reporting to disable as they default CE MUST set the packet call state reporting to disable when the Rm Interface is torn down note Note: this could be due to the data cable being removed or the device power cycling. CE MUST return “ERROR” for any other AT+CPSR string 3.1.
AT Command User Manual 4 Qualcomm Proprietary AT Command Set 4.1.
AT Command User Manual note CE MUST return “ERROR” for any other AT$QCMIPT string 4.1.4 $QCMIPEP: Disable/Enable the active profile description Disable/Enable the active profile $QCMIPEP: AT$QCMIPEP? OK format parameter AT$QCMIPEP= OK 0: disable the active profile 1: enable the active profile AT$QCMIPEP? $QCMIPEP: 1 example OK AT$QCMIPEP=1 OK note CE MUST return “ERROR” for any other AT$QCMIPEP string 4.1.
AT Command User Manual AT$QCMIPGETP=0 Profile:0 Enabled NAI:00000000000000@hcm.sprintpcs.com Home Addr:0.0.0.0 Primary HA:68.28.15.12 Secondary HA:68.28.31.12 MN-AAA SPI:1234 MN-HA SPI:1234 Rev Tun:1 MN-AAA SS:Set MN-HA SS:Set OK CE MUST separate each line of the profile with exactly one carriage return and line feed note CE MUST not display the SS (Shared Secret) CE MUST return “ERROR” for any other AT$QCMIPGETP string 4.1.
AT Command User Manual 4.1.
AT Command User Manual AT$QCMIPMASSX=, OK format $QCMIPMASSX: (Set|Unset) OK AT$QCMIPMASSX? parameter example the user entered hex Mobile Node AAA shared secret of up to 16 bytes 0: not save the change to NV memory 1: save the change to NV memory AT$QCMIPMASSX=aaa,0 OK AT$QCMIPMASSX? $QCMIPMASSX: Set OK CE MUST return “ERROR” if the user entered Mobile Node AAA shared secret begins with “0x” for AT$QCMIPMASSX.
AT Command User Manual AT$QCMIPMHSS? $QCMIPMHSS: Unset OK The Mobile Node Home Agent shared secret string MUST be enclosed note between double quotes 4.1.
AT Command User Manual AT$QCMIPMASPI=, parameter OK the user entered Mobile Node AAA SPI integer value between (0-4294967295) 0: not save the change to NV memory 1: save the change to NV memory AT$QCMIPMASPI? $QCMIPMASPI: 2,1 example OK AT$QCMIPMASPI=1234,0 OK note CE MUST return “ERROR” for any other AT$QCMIPMASPI string. 4.1.
AT Command User Manual AT$QCMIPPHA? 192.168.1.10,0 example OK AT$QCMIPPHA=”192.168.1.10”,0 OK note CE MUST return “ERROR” for any other AT$QCMIPPHA string. 4.1.15 $QCMIPSHA: Set secondary Home Agent IP Address description Set secondary Home Agent IP Address , AT$QCMIPSHA? OK format AT$QCMIPSHA =””, OK parameter the Secondary Home Agent IP Address string MUST be enclosed between double quotes. Valid values for X are ( (0-255).
AT Command User Manual 5.1.1 ATD: Make a packet data call description Make a packet data call format ATD OK example ATD#777 OK CE MUST ignore any and establish a packet data call. Note: in the past only #777, which is configured in a NV item, would cause the device to establish a packet data connection.
AT Command User Manual AT$MIPERR? $MIPERR: 0 example OK note CE MUST return “ERROR” for any other AT$MIPERR string. 5.1.5 $ERI: Return the current Enhanced Roaming Indicator value description Return the current Enhanced Roaming Indicator value $ERI: format AT$ERI? OK parameter decimal as defined in the Sprint Enhanced Roaming Indicators document [9] AT$ERI? $ERI: 0 example OK note CE MUST return “ERROR” for any other AT$ ERI string 5.1.
AT Command User Manual AT$RMGUARD=2 ERROR AT$RMGUARD=? $RMGUARD: 1 OK note CE MUST return "ERROR" for any other AT$RMGUARD string 5.1.8 $PRL: Get CDMA PRL version of the device description Get CDMA PRL version of the device format AT$PRL? +PRL: +PRL: 201 example AT$PRL? OK note “AT$PRL?” which will return the CDMA PRL version of the device. 5.2 OMA-DM commands 5.2.
AT Command User Manual format parameter example AT+OMALOG= AT+OMALOG=? OK +OMALOG: OK 0:disable OMA-DM client logging 1:enable OMA-DM client logging. CE MUST write the complete OMA-DM XML transactions to a single file in the EFS for later retrieval when OMA-DM client logging is turned on AT+OMALOG=1 OK AT+OMALOG=? +OMALOG: 1 OK CE MUST return "ERROR" for any other AT+OMALOG string note Factory Settings must set the value of AT+OMADM to 0 5.
AT Command User Manual 1: enable PRL update capabilities. 2: perform a client initiated PRL update 3: set the device to check for PRL updates every 45 days 4: set the device to check for PRL updates every 90 days. 5：cancel PRL session example AT+PRL=1 OK AT+PRL=? +PRL: 1 OK Factory Settings must set the value of AT+PRL to 1 note CE MUST return "ERROR" for any other AT+PRL string "AT+PRL=?" which will return the current PRL update setting. 5.2.
AT Command User Manual example +HFAR: FAIL,25346 note 5.2.9 +DCR: START the start sign of DC session description the start sign of DC session +DCR: START: parameter example +DCR: START note 5.2.10 +DCR: SUCCESS the success sign of DC session description the success sign of DC session +DCR: SUCCESS parameter example +DCR: SUCCESS note 5.2.
AT Command User Manual note 5.2.14 +PRLR: FAIL the fail sign of PRL session description the fail sign of PRL session +PRLR: FAIL, parameter example +PRLR: FAIL,25346 note 5.2.15 +FUMOR: IF_DOWNLOAD the start sign of FUMO session description the start sign of FUMO session +FUMOR: IF_DOWNLOAD parameter +FUMOR: example IF_DOWNLOAD note 5.2.
AT Command User Manual The time of install of delta packet example +FUMORSec: 25 note 5.2.19 +FUMORBytes: The size of delta packet description The size of delta packet +FUMORByt e: parameter The size of delta packet example +FUMORBytes:6234 note 5.2.20 +FUMOR: FAIL the fail sign of FUMO session description the fail sign of FUMO session +FUMOR: FAIL , parameter example +FUMOR: FAIL,25346 note 5.2.
AT Command User Manual +PRLR: NO_CONTENT parameter example +PRLR: NO_CONTENT note 5.2.24 +FUMOR: NO_CONTENT the no content sign of FUMO session description the no content sign of FUMO session +FUMOR: NO_CONTENT parameter +FUMOR: example NO_CONTENT note 5.2.
AT Command User Manual example AT$RTN=000000 OK CE MUST set the device to factory defaults and power cycle the device if the correct MSL is entered note CE MUST return "ERROR" if the MSL is not correct and not power cycle the device CE MUST return "ERROR" for any other AT$RTN string 5.3.
AT Command User Manual n format AT$DEBUG? : OK AT$DEBUG? 1x Engineering State : Idle SO : 3 …. parameter example OK 5.5 FCC Regulations lThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
AT Command User Manual only. The antenna installation and operating configurations of this transmitter, including any applicable source-based time-averaging duty factor, antenna gain and cable loss must satisfy MPE categorical Exclusion Requirements of §2.1091.
