MC7010CA Quick Start Guide 1
View this label to get the default Password . ┌ Scan this QR code to download the Install Helper application.
LEGAL INFORMATION Copyright © 2021 ZTE CORPORATION. All rights reserved. No part of this publication may be quoted, reproduced, translated or used in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. Notice ZTE Corporation reserves the right to make modifications on print errors or update specifications in this guide without prior notice.
Unpacking and Preparations Before installing the device, make sure that all items listed in the packing list are present. If something is missing or damaged, pleasecontact ZTE technical support.
Prepare the following accessories(not included): Crosshead screwdriver Flat head screwdriver Hammer drill Marker pens Installation Precautions Do not install the device in the following directions: Do not install the device with Do not install the device Do not install the device the horizontally. tilted. interface side facing upwards. WARNING! The device must be installed downwards and vertically.
zone. When installing the device against a pole, do not install a lightning rod on the pole. It is recommended that an independent lightning rod be installed near the pole. If a lightning rod is installed on the pole, it is recommended that the lightning rod be led out and grounded directly. The mounting pole must be firm, cannot be shaken and must meet the wind-resistant requirements (not less than level-10 wind speed).
Recommended Installation Locations 7
1.Installing the nano-SIM Card Insert the nano-SIM card to the SIM card slot as shown. WARNING! Your device does not support(U)SIM cards,micro-SIM cards or any other non-standard SIM cards. To avoid damage to the device, do not use those cards or any card holders.
2.Installing the Network Cable 1. Connect the RJ45 to the network port on the MC7010CA while the two screws are also inserted into the holes at the bottom of the device. 2. Push the cover plate upwards until it is secured, and use a screw anti-theft removal wrench to install the cover plate on the device. 3. Reserve enough length of the network cable,and crimp the RJ45.
3.Using Install Helper Application to Detect Position Before installingthe MC7010CA, you can install the Install Helper applicationon your mobile phone and connect to the device to detect the signal strength and help you detect and locate the installation location. NOTE: View the label on this guide to get the link or QR cord to download the Install Helper application. Powering on the MC7010CA 1. Connect the CAT5Enetwork cable which is from the MC7010CA to the network port(RJ45-2) on the POE adapter. 2.
Terrible).You can touch view details to view the network details. When the device signal is detected, your phone automatically beeps. The louder the sound and the stronger the vibration, the better the signal strength. NOTE: Touch FINISH to end the detection and select whether to save the current position if needed. 4. Continue the detection until the desired position is detected, and save or continue to adjust the position as prompted.
4.Installing Your Device Installing the Device on a Wall 1. Mark the positions for drilling holes on the wall. 2. Firstly, use a 6mmpercussion drill to drill holes at the marked positions, and install four M6 expansionspigots.Secondly, use four M6 expansion bolts to fix the bracket to the wall. CAUTION: The screw hole of the bracketfaces upwards. down.Otherwise,the screw cannot be installed later.
3. Use fourM3 crosshead screws to install the backplaneon the device. 4. Firstly, fasten the backplane to the installed bracket through the upper and lower slots, and align the hole on thebackplane with the hole on the bracket.Secondly, use one M3crosshead screw to install the MC7010CA on the bracket.
Installing the Device against a Pole 1. Use ascrewdriverto loosen the clamp and release the buckle. 2. Pass the clamp through the U-shape groove on the bracket to install the bracket against the pole. CAUTION: The screw hole of the bracket faces upwards. Do not install the bracketupside down.Otherwise,the screw cannot be installed later. 3. Adjust the clamp to the proper tightening position, press the buckle and use a screwdriver to lock the clampto fix the bracket.
4. Use four M3 crosshead screws to install the backplane on the device.
5. Firstly, fasten the backplane to the installed bracket through the upper and lower slots, and align the hole on the backplane with the hole on the bracket. Secondly, use one M3crosshead screw to install the MC7010CA on the bracket. NOTE: Before installing the device on the bracket, you can move the device horizontally and slowly on the pole tofurther adjust the position if needed.
5.Connecting the POE Adapter 1. Connect the CAT5Enetwork cable which is from the MC7010CA to the network port(RJ45-2) on the POE adapter. 2. Connect the PC network port(RJ45-1) on the POE adapterto yourPC/IDU(router) with the RJ-45 network cable.
Installation Check Device Installation: The MC7010CA is installed firmly. The network cables are installed firmly. The cover plate on the device is installed. The nano-SIM card is installed. The network interface on the POE adapter is installed correctly. CablesInstallation: Verify that all cables are connected properly, cable connectors aresecure. Cables should be laid in aclear and straight manner without crossing each other. There is no obvious curve or slant.
System Power-On Powering on the device Connect the power connector on the POE adapter to the socket. The POE adapter starts to supply power to the MC7010CA. When the indicatorof the POE adapter and the POWER LEDof thedevice turns green, the MC7010CAis correctly powered. Preliminary Device Acceptance 1. Check indicator status. 2. Connect the device to a PC and log in to the configuration pageto view the device status.
LED Behavior When setting up the MC7010CA, the LED will have the following behavior. Indicator Status POWER On Description Power is on and external power supply is working normally. Off Power is off. NETWORK Red blinking Green on The device is in error status: • The device isnot registered to the mobile network. • There is no nano-SIM card inserted. • There is no network service available. The device isregistered or connected to the 5G networkand data is being transferred.
Logging in to the MC7010CA Page 1. Ensure that the connection between your device and the PC/ routeris correct. 2. Launch the Internet browser and enter http://192.168.254.1 in the address bar. 3. Enter the passwordto log in to the MC7010CA configuration page NOTE: View the label on this guideto get the default password.
Accessing the Internet After a PC/router is successfully connected to your device, you can access the Internet in Automatic or Manual mode. The default mode is Automatic. Mode Automatic Operation Your device is automatically connected to the Internet, and you can surf on the Internet through the router. Manual 1. Log in to the MC7010CA configuration page. 2. Select Set internet>Connection Mode> Manual, and then click Apply. 3. Click page, twiceto return to the home and click or .
Confirming the Connection Status and Making More Settings Confirming the Connection Status The connection status related information is displayed when you log in to the configuration home page, and the Status Information below shows the information about System information, LAN details, Cellular connection status, WAN connection status and advanced status details. You can touch Detail Informationto get more details. To see details on the connected session, touch Data Usageat the bottom left of the page.
Troubleshooting Problem Recommended Action The PC/router connected the to device available. cannot access the Internet. Ensure that your nano-SIMcard is Change the location and find a place with good signal. Check the settings of the LAN connection mode. Contact your service provider and confirm your APN settings. The Enter the correct address. The MC7010CA default configuration http://192.168.254.1. page cannot be visited.
Getting More Help You can get help by: •Sending an email to mobile@zte.com.cn • Visiting www.ztedevices.
Warning and Notice Radio Frequency Interference General Statement on Interference Some electronic devices may be susceptible to electromagnetic interference. Locate the device away from TV set, radio and other electronic equipment to avoid electromagnetic interference. Medical Equipment Switch off your wireless device when you are requested to do so in hospitals, clinics or healthcare facilities. These requests are designed to prevent possible interference with sensitive medical equipment.
Do not wrap, seal or cover the device with towels or other objects. Do not use the device in a closed environment such as a box to avoid damage to the device due to poor heat dissipation. Do not allow the device or accessories to come into contact with liquid or moisture at any time. Do not immerse the device in any liquid. Your device may become warm during normal use. If the device temperature is too high, do not touch it. Do not touch the antenna unnecessarily.
To avoid short circuit, malfunction or electric shock, do not touch the device or power adapter with wet hands. When the power adapter is exposed to rain, liquid or severe moisture, stop using it and contact an authorized service center for inspection. Cleaning and Maintenance The recommended operating temperatures are -40 °C to +55 °C and the storage temperatures are -40 °C to +70 °C. The humidity range is 5% ~ 95%.
This warranty does not apply to defects or errors in the product caused by: i. Reasonable abrasion. ii. End users’ failure to follow ZTE’s installation, operation or maintenance instructions or procedures. iii. End users’ mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product. iv. Modifications or repairs not provided by ZTE or a ZTE-certified individual. v.
FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.
IC: 5200E-MC7010CA IC Radiation Exposure Statement This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This equipment should be installed and operated with minimum distance 1.5 cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
