MF79S Quick Start Guide ZTE CORPORATION ZTE Plaza, Keji Road South, Shenzhen, China 1
Getting to t Know You ur Device Appearanc ce The following fiigure is for your referrence only. 1. Device cap 2. Front cover 3. Indicator ligh ht 4. USB connecctor 5. microSDHC™ ™ card slot 6. (U)SIM card slot NOTE: microSDHC log go is a tradem mark of SD-3C, LLC. *If you want to connect an adapter to your device, the output o of hould be 5V/1A.
installing or removing the (U)SIM card. Getting to Know Your Device Indicator Light Indicator Status Description Error status. Not registered to the mobile network, no (U)SIM Red card inserted or no network service available. Green solid Registered to 2G/3G network. Green Connected to 2G/3G network blinking and data is being transferred. Blue solid Registered to LTE network. Blue Connected to LTE network blinking and data is being transferred. Blue WPS is active.
Blue solid Wi-F Fi is active. LED off Wi-F Fi is off. Getting to t Know You ur Device Connection Scenarios The device usses your (U)SIM carrd to access the Intternet. It allows multiple clients to surf on th he Internet at the sam me time. The following fiigure is for your referrence only. NOTE: With other acccessories, such as mobile power or ca ar power adapter, you can c supply power to your device and d use it anywhere and anytime.
Installing g Your Devic ce 1. Open the frront cover. 2. Install a (U)S SIM card to the (U)SIIM card slot. WARNING G! Your device do oes not support micro o-SIM cards, nano-SIM cards or any other no on-standard SIM carrds. To avoid damag ge to the device, do not use u those cards or any card holders.
3. Install a microSDHC card to the microSDHC card slot. 4. Close the front cover.
Connectting to Your Device Using USB B Connector Insert the devicce into your computter’s USB port securrely. The operating systtem automatically detects d and identifiies your device and starrts the installation wizzard. NOTE: If the system does not automaticallyy launch installation, you can click the device e installation icon in My M Computer > ZTEMODEM to install the so oftware.
Using Wi-F Fi 1. Supply powe er to your device by connecting to your computer c or using othe er accessories. 2. Ensure thatt your computer orr other client devices have enabled Wi-Fi, and search for avvailable wireless netw works. NOTE: Refer to your Wi-Fi-enabled clien nt device manual fo or further details on how w to search for wirele ess networks. If yo ou use a computer, you need to set your computer to obtain an IP address automatically. 3.
Logging in to th he 4G Mobile Hotspot Configuration Page 1. Ensure that the connection between your device and the e is correct. client device 2. Launch the Internet browser and d enter http://192.16 68.0.1 or http://ufi.zte edevice.com in the address a bar. 3. Enter the password p to log in to the 4G Mobile Hotspot configuration n page. NOTE: The default passsword is admin. Changing the W Wi-Fi SSID Passworrd 1. Log in to the e 4G Mobile Hotspot configuration page. 2.
Accessin ng the Intern net After a client device d is successfullly connected to yourr device, you can accesss the Internet in Auto omatic or Manual mo ode. The default mode iss Automatic. Mode Operation Automatic Your device is au utomatically connecte ed to the Internet, and you can surf on the Internet through the clientt. Manual 1. Log in to the 4G Mobile Hotspot configuration page. p 2. Select curre ent network Settiings > Connection Mode M > Manual, and a then click Apply.
Configuring Your PC The following procedure describes how to configure the Internet Protocol in Windows 7 for your Wi-Fi connection. 1. Right-click Network and select Properties. 2. Select Change adapter settings. 3. Right-click Wireless Network Connection and select Properties. 4. Select Internet Protocol Version 4 (TCP/IPv4), and click Properties. 5. Select Obtain an IP address automatically and Obtain DNS server address automatically, and click OK.
• • • • • • • • • • Be aware of the usage limitation when using the device at places such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Power off the device if necessary. Do not use electronic transmission devices in aircrafts, at petrol stations or in hospitals. Observe and obey all warning signs, and power off the device in these conditions. Do not touch the inner antenna area unless necessary.
• • • Handle the device carefully. Do not drop, bend or strike it. Otherwise the device may be damaged. Only qualified personnel can dismantle and repair the device. An operating temperature between -10°C and +60°C and humidity between 5% and 95% are recommended. Limited Warranty This warranty does not apply to defects or errors in the product caused by: i. Reasonable abrasion. ii. End users’ failure to follow ZTE’s installation, operation or maintenance instructions or procedures. iii.
Limitation of Liability ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, no matter whether or not ZTE had been advised, knew or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost.
-Consult the dealer or an experienced radio/TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Body Operation This device was tested for typical body support operations. To comply with RF exposure requirements, a minimum separation distance of 0.5 cm must be maintained between the user’s body and the device, including the antenna.
LEGAL INFORMATION Copyright © 2016 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No.: R1.
Troubleshooting Problem Recommended Action When you insert the device into your computer’s USB port, the Install the software, and run the installation program in the path of My Computer/ZTEMODEM. If the driver of your device is operating system abnormal, reinstall the software. can You need to uninstall the software not the install software first. automatically.
Troubleshooting Problem The Recommended Action client connected to the device cannot access the Internet. Ensure that your (U)SIM card is available. Change the location and find a place with good signal. Check the settings of the WAN connection mode. Contact with your service provider and confirm your APN settings. The 4G Mobile Hotspot configuration page Enter the correct address. The default address is http://192.168.0.1 or http://ufi.ztedevice.com. cannot be visited.
Getting More Help You can get help by: Sending an email to mobile@zte.com.cn Visiting www.ztedevice.
