MF833U1 USB Modem Quick Start Guide ZTE CORPORATION NO. 55, Hi-tech Road South, Shenzhen, P.R.
Getting Modem to Know Your Your modem supports data and SMS services through the mobile phone network, enabling you to communicate anytime and anywhere. The following figure is only for your reference. The actual product may be different. 1. Modem cap 2. Front cover 3. Indicator light 4. USB connector 5. microSDHC™ card slot 6. micro-SIM card slot NOTE: microSDHC logo LLC.
Installing the micro-SIM Card and microSDHC Card 1. Press and push the front cover and remove it. NOTE: Do not open the front cover rudely. Failing to do so may cause damage to the front cover. 2. Install a micro-SIM card to the micro-SIM card slot. WARNING! Your modem does not support SIM cards and nano-SIM cards. To avoid damage to the modem, do not use those cards or any card holders.
3. Install a microSDHC card to the microSDHC card slot. 4. Slide the front cover gently back into place.
Connecting the Modem to Your PC Insert the modem into your computer’s USB port securely. The operating system automatically detects and identifies your modem and starts the installation wizard. NOTE: If the system does not launch installation automatically, you can double-click the modem installation icon in My Computer > ZTEMODEM to install the software.
Accessing the Internet After the modem is connected to your computer successfully, you can access the Internet in Automatic or Manual mode. The default mode is Automatic. Mode Automatic Operation Your modem is connected to the Internet automatically, and you can surf on the Internet directly. Manual 1. Log in to the 4G Hostless Modem configuration page. 2. Select Network Settings > Connection Mode > Manual, and then click Apply. 3. Click to return to the home page, and then click or .
Getting More Help You can get help by: Sending an email to mobile@zte.com.cn Visiting www.ztedevices.
LEGAL INFORMATION Copyright © 2020 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No.: R1.
Warning and Notice Using Your Modem If inadequately shielded, some electronic devices may be affected by the electromagnetic interference caused by the modem, such as the electronic system of vehicles. Consult the manufacturers of such devices before using the modem if necessary. Operating the modem may interfere with medical instruments such as hearing aids and pacemakers. Always keep the modem more than 20 centimeters away from such medical instruments when your modem is turned on.
Do not touch the inner antenna area unless it is necessary. Otherwise the performance of the modern may be affected. Keep the modem out of the reach of little children. The modem may cause an injury if used as a toy. When the modem is operating, do not touch the metallic parts. Failing to do so may cause burns. Use original accessories or accessories that are authorized.
Only qualified personnel can dismantle and repair the modem. An operating temperature between -10 °C and +55 °C and a humidity between 5% and 95% are recommended. Limited Warranty This warranty does not apply to defects or errors in the product caused by: i. ii. Reasonable abrasion. End users’ failure to follow ZTE’s installation, operation or maintenance instructions or procedures. iii.
or receive a refund for the product from ZTE under the above-mentioned situations. This warranty is end users’ sole remedy and ZTE’s sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the implied warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law.
FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
lower the power output. The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands.
SAR compliance for body operation is based on a separation distance of 5 mm between the unit and the human body. Carry this device, at least 5 mm away from your body to ensure RF exposure level compliant or lower to the reported level. To support body operation, choose the belt clips or holsters, which do not contain metallic components, to maintain a separation of 5 mm between this and your body.