User Guide AT&T Velocity® USB Stick
Contents Get Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Know Your Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Set Up and Connect to the Internet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disconnect and Remove the Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Copyright © 2017 ZTE CORPORATION. All rights reserved.
Get Started Health and Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 To the Owner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Using Your USB Stick. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 RF Exposure Information (SAR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 FCC Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Indicator Light The color and behavior of the light indicates the device’s current status regarding network connection, nano-SIM card, software updates, and more. Color Nano-SIM card slot USB folding hinge Green External antenna connector Yellow External antenna connector – Allows an external antenna to be connected, if necessary. USB folding hinge – Allows the USB connector to fold in for storage or out to plug into a computer.
3. The operating system will automatically detect and recognize your device and install any needed drivers. (If you are using a Mac, see Install the Driver (Mac ® OS X ®) below.) Note: Compatible with many operating systems; see Supported Operating Systems on page 22 for details. Installation may vary depending on your operating system and version. Connect to the Internet Once installation is complete, your device will automatically connect to the network.
Use the AT&T Velocity USB Stick View Network Information This chapter describes the main features of the web site for managing and configuring the device. On the right side of the status bar at the top of the management web site, you can view network information, such as the signal strength, operator, and network mode. Management Web Site Launch a browser and enter http:/attusbmodem/ or http://192.168.1.1 in the address bar.
View Messages View Details Your device can receive important messages from AT&T about your service plan and software updates for your device. You cannot reply to them. The indicator light will turn yellow and blink when you have a new message (see Status Indicator Light on page 5). You can view details about your device, such as the wireless number, hardware version, and IMEI. From the management web site, click About on the menu. View Local Time and Time Zone 1.
Replace the Nano-SIM Card Reset the Device The device comes with a nano-SIM card preinstalled. Should you need to swap out your nano-SIM card, follow these instructions. You can reset the device to its original factory settings. WARNING! To avoid damage to the device, do not use any other kind of SIM card, or any nonstandard nano-SIM card cut from a SIM card. You can get a standard nano-SIM card from your service provider.
Advanced Settings Configure APN Details This chapter provides information on how to configure advanced settings for the device, such as APN, firewall, SIM PIN, and more. The Access Point Name (APN) is checked to determine the type of network connection to establish. Your device comes preconfigured with the APN for AT&T. Note: Disconnect the device from the network before changing any settings (see Disconnect From the Internet on page 7). Add an APN for Another Network 1.
Remove an APN Entry 1. From the management web site, click Settings on the menu. 2. From the drop-down box beside Profile Selection, select the APN you want to remove. 3. Click Delete. Note: You cannot delete the default profile. Set another profile as the default before attempting to delete. Enable MAC/IP/Port Filtering You can enable or disable the MAC/IP/Port Filtering feature as needed to block certain Internet traffic.
Port Filtering Options 2. Under Current MAC/IP/Port filtering rules in system, click to check the box beside the rule you want to delete. 3. Click Delete. • MAC Address – Set the MAC address to be filtered. • D estination IP Address – Set the destination IP address to be filtered. • Source IP Address – Set the source IP address to be filtered. • Protocol – Select which protocol will be used for filtering.
Configure SIM PIN If the SIM PIN feature is enabled for the nano-SIM card in your device, you will need to enter the PIN when you log in for the first time. To change the SIM PIN status, you need to disconnect from the network first (see Disconnect From the Network on page 7 for details). Note: The nano-SIM card will be locked if you enter the wrong PIN three times consecutively. Troubleshooting Problem Cannot access the Internet Enable or Disable the SIM PIN 3.
Specifications Health and Safety Information Mechanical Specifications To the Owner Dimensions Weight Memory USB Version Connectivity 3.82" (L) x 1.30" (W) x 0.63" (D) 3.17 oz. 256 MB RAM/512 MB ROM USB 2.
Using Your USB Stick RF Exposure Information (SAR) • U se original accessories or accessories that are authorized. Using any unauthorized accessories may affect the performance of the modem and violate the related national regulations about telecom terminals. This device meets the government’s requirements for exposure to radio waves. • A void using the modem near or inside metallic structures or establishments that can emit electromagnetic waves, because signal reception may be affected.
with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: SRQ-MF861. This device has been tested and meets the FCC RF exposure guidelines.
Warranty ZTE offers you a limited warranty that the enclosed subscriber unit and its enclosed accessories will be free from defects in material and workmanship for a period that expires one year from the date of sale of the Product to you, provided that you are the original end user and purchaser of the Product and provided that your purchase was made from a supplier authorized by the Seller. Transfer or resale of a Product will automatically terminate warranty coverage with respect to that Product.
LIMITED WARRANTY How to Get Warranty Service TO THE EXTENT PERMITTED BY APPLICABLE LAW, THIS LIMITED WARRANTY IS YOUR SOLE AND EXCLUSIVE REMEDY AGAINST ZTE AND ZTE’S SOLE AND EXCLUSIVE LIABILITY IN RESPECT OF DEFECTS IN PRODUCT. HOWEVER, THIS LIMITED WARRANTY SHALL NOT EXCLUDE NOR LIMIT ANY OF YOUR LEGAL (STATUTORY) RIGHTS UNDER THE APPLICABLE NATIONAL LAWS. o obtain warranty service, please call (877) 817-1759.
32
