MF920U Quick Start Guide 1
ZTE CORPORATION NO. 55, Hi-tech Road South, Shenzhen, P.R.China Postcode: 518057 Getting to Know Your Device Appearance The following figure is for your reference only.
1. Charging/micro-USB jack 2. Indicator light 3. Power key Press and hold for about 2 seconds to power on/off your device. Press and hold for about 10 seconds to power off your device, if it is in abnormal status. And then press and hold for about 2 seconds to power on your device again. 4. WPS key Press and hold for about 2 seconds to activate the WPS function. 5. micro-SIM card slot and reset hole Reset hole: Press and hold for about 2 seconds to restore your device to the factory settings.
Getting to Know Your Device Indicator lights Indicator Battery Status Description Red solid / The battery is low. Please blinking charge the battery. Green The battery is being blinking charged. Green The battery level is middle solid or high. Light off Your device is powered off and not being charged. Wi-Fi SMS Blue solid Wi-Fi is active. Blue WPS is active. blinking Light off Wi-Fi is off. Blue solid You have unread messages.
Blue You have new messages or blinking the message storage is full. Light off There is neither an unread message nor a new message. Red The device is in error Network status. The device is not registered to the mobile network. There is no micro-SIM card inserted. There is no network service available. Green The device is registered to solid the 2G/3G mobile network. Green The device is connected to blinking the 2G/3G mobile network and data is being transferred.
Blue The device is connected to blinking the 4G LTE network and data is being transferred. Getting to Know Your Device Connection Scenarios The device uses your micro-SIM card to access the Internet. It allows multiple clients to surf on the Internet at the same time. The following figure is for your reference only.
Installing Your Device 1. Open the micro-SIM card slot cover. NOTE: Do not remove the cover rudely, because it is connected with the device. 2. Install a micro-SIM card to the micro-SIM card slot. WARNING! Your device does not support SIM cards, nano-SIM cards or any other non-standard micro-SIM cards. To avoid damage to the device, do not use those cards or any card holders. 3. Close the micro-SIM card slot cover.
Connecting to Your Device Using Wi-Fi 1. Power on your device. 2. Ensure that your computer or other client devices have enabled Wi-Fi, and search for available wireless networks. NOTE: Refer to your Wi-Fi-enabled client device manual for further details on how to search for wireless networks. If you use a computer, you need to set your computer to obtain an IP address automatically. 3. Select the Wi-Fi name (SSID) of your device, and click Connect. 4. Enter the Wi-Fi password if necessary, and click OK.
Using a USB Cable 1. Connect a computer to your device with a USB cable. 2. Power on your device. The operating system detects and identifies new hardware, and automatically installs the software. NOTE: If the system does not automatically launch installation, you can double-click the device installation icon in My Computer > ZTEMODEM to install the software. 3. Wait until the computer is connected to your device successfully.
Getting to Know the Wi-Fi SSID and Password You can view the label on the device to get the default Wi-Fi SSID and password.
Logging in to the 4G Mobile Hotspot Configuration Page 1. Ensure that the connection between your device and the client device is correct. 2. Launch the Internet browser and enter http://192.168.0.1 or http://ufi.ztedevice.com in the address bar. 3. Enter the password to log in to the 4G Mobile Hotspot configuration page. NOTE: You can view the label on the device to get the default password.
Changing the Wi-Fi SSID or Password 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select Wi-Fi Settings. 3. Change the Network Name (SSID) or the Password in the Main SSID area. 4. Click Apply.
Accessing the Internet After a client device is successfully connected to your device, you can access the Internet in Automatic or Manual mode. The default mode is Automatic. Mode Automatic Operation Your device is automatically connected to the Internet, and you can surf on the Internet through the client. Manual 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select network Settings > Connection Mode > Manual, and then click Apply. 3.
• To modify the parameters of your device, log in to the 4G Mobile Hotspot configuration page.
Configuring Your PC The following procedure describes how to configure the Internet Protocol in Windows for your Wi-Fi connection. 1. Right-click Network and select Properties. 2. Select Change adapter settings. 3. Right-click Wireless Network Connection and select Properties. 4. Select Internet Protocol Version 4 (TCP/IPv4), and click Properties. 5. Select Obtain an IP address automatically and Obtain DNS server address automatically, and click OK.
Warning and Notice To the Users • • • • • • If inadequately shielded, some electronic devices, for example, the electronic system of vehicles, may be affected by the electromagnetic interference caused by the device. Consult the manufacturers of such devices before using the device if necessary. Operating the device may interfere with medical instruments such as hearing aids and pacemakers. Always keep the device more than 20 centimeters away from such medical instruments when your device is powered on.
• • • • • • • • • • • • Keep the device out of the reach of small children. The device may cause an injury if used as a toy. When the device is operating, do not touch the metallic parts. Failing to do so may cause burns. Use original accessories or accessories that are authorized. Using any unauthorized accessories may affect the performance of the device and violate the related national regulations about telecom terminals.
Battery Safety WARNING! The battery is not removable. Removal may cause fire or explosion. • Using ZTE-unapproved or incompatible battery, charger or power adapter may damage your device, shorten its lifespan or cause a fire, explosion or other hazards. • The recommended operating temperatures are 0 °C to 35 °C and the storage temperatures are -20 °C to +45 °C. Extreme temperatures can damage the device and reduce the charging capacity and lifespan of your device and battery.
Limited Warranty This warranty does not apply to defects or errors in the product caused by: i. Reasonable abrasion. ii. End users’ failure to follow ZTE’s installation, operation or maintenance instructions or procedures. iii. End users’ mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product. iv. Modifications or repairs not provided by ZTE or a ZTE-certified individual. v.
Limitation of Liability ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, no matter whether or not ZTE had been advised, knew or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost.
LEGAL INFORMATION Copyright © 2019 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No.: R1.0 Edition Time: May 31, 2019 Manual No.
Troubleshooting Problem Recommended Action The connection Install the software. Please run the installation program in the path of between your device and a My Computer > ZTEMODEM. If the driver of your device is PC through a abnormal, reinstall the software. USB You need to uninstall the software cable cannot be first. established. The connection enabled. between your device and a client Check the IP address, and ensure that your client can automatically be established.
Troubleshooting Problem Recommended Action The client connected to the device available. cannot access the Internet. Ensure that your micro-SIM card is Change the location and find a place with good signal. Check the settings of the WAN connection mode. Contact your service provider and confirm your APN settings. The 4G Enter the correct address. The Mobile default Hotspot http://192.168.0.1 configuration page cannot address is or http://ufi.ztedevice.com. be visited.
Getting More Help You can get help by: Sending an email to mobile@zte.com.cn Visiting www.ztedevices.
Accessory designed by ZTE or available on market for maintaining 10 mm using distance must be used for RF exposure compliance. FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.
exposure level compliant or lower to the reported level. To support body operation, choose the belt clips or holsters that do not contain metallic components to maintain a separation of 10 mm between this device and your body.
