R216-Z Quick Start Guide ZTE CORPORATION NO. 55, Hi-tech Road South, ShenZhen, P.R.
Getting to Know Your Device Appearance The following figure is for your reference only. 1. External Antenna 2. Charging/micro-USB Jack 3. Indicators 4. Power Button 5. WPS Key Press and hold it for 5 seconds to activate the WPS function. 6.
Getting to Know Your Device Indicators When the device is powered on, the following icons may be displayed on the LCD screen. For a description of the icons, refer to the following table. Indicator Status Description Red solid Error status. Not registered to the mobile network, no (U)SIM card inserted or no network service available. Green solid Registered to the mobile network. Green blinking Connected to the mobile network and data is being transferred. Blue solid WPS is active.
LED light off Battery No new messages. Red blinking The battery is empty. Please charge the battery. Red solid The battery is low. Please charge the battery. The battery is in the over-voltage charging status. Blinks every 2 seconds when Green blinking the battery is being charged. Blinks every 8 seconds when your device is in sleep mode and not being charged. Green solid The battery level is middle or high.
Installing Your Device 1. Open the (U)SIM card cover. NOTE: Do not remove the cover rudely, because it is connected with the device. 2. Install a (U)SIM card to the (U)SIM card slot. WARNING! Your device does not support the micro/nano-SIM card or any other non-standard SIM cards.
device, do not use those cards or any card holders. 3. Close the (U)SIM card cover. Connecting to Your Device Using Wi-Fi 1. Power on your device. 2. Make sure your computer or other client devices have enabled Wi-Fi, and search for available wireless networks. NOTE: Refer to your Wi-Fi-enabled client device manual for further details on how to search for wireless networks. If you use a computer, you need to set your computer to obtain an IP address automatically. 3.
Using a USB Cable 1. Connect a computer to your device with a USB cable. 2. Power on your device. The operating system detects and identifies new hardware, and automatically installs the software. NOTE: If the system does not automatically launch installation, you can run the installation program in the My Computer/ Vodafone QuickStart path. 3. Wait until the computer is connected to your device successfully.
(15.0 or later), Opera (10.0 or later), Safari (4.0 or later), or Google Chrome (10.0 or later). 3. Enter the password to log in to the 4G Mobile Hotspot configuration page. NOTE: The default password is admin. Changing the Wi-Fi SSID or Password 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select Mobile Wi-Fi > Wi-Fi > Security. 3. Change the SSID or the Key (Password) in the Security Settings area. 4. Click Save.
Connection > Connection Mode > Prompt, and then click Save. 3. Click Connect to connect to the Internet manually. NOTE: To modify the parameters of your device, log in to the 4G Mobile Hotspot configuration page. Configuring Your PC The following procedure describes how to configure the Internet Protocol in the Windows 7 operating system for your Wi-Fi connection. 1. Right-click Network and select Properties. 2. Select Change adapter settings. 3.
Warning and Notice To the Owner • If inadequately shielded, some electronic devices, for example, the • • • • • • • electronic system of vehicles, may be affected by the electromagnetic interference caused by the device. Consult the manufacturers of such devices before using the device if necessary. Operating the device may interfere with medical instruments such as hearing aids and pacemakers.
Warning and Notice To the Users • Use original accessories or accessories that are authorized. Using any unauthorized accessories may affect the performance of the device and violate the related national regulations about telecom terminals. • Avoid using the device near or inside metallic constructions or establishments that can emit electromagnetic waves, because signal reception may be affected. • The device is not waterproof. Keep the device dry and store it in a shady and cool place.
Warning and Notice iii. End users’ mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product. iv. Modifications or repairs not provided by ZTE or a ZTE-certified individual. v. Power failures, surges, fire, flood, accidents, and actions of third parties or other events outside ZTE’s reasonable control. vi. Usage of third-party products or usage in conjunction with third-party products if such defects are due to the combined usage. vii.
LEGAL INFORMATION Copyright © 2014 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No.: R1.
Troubleshooting Problem Recommended Action The connection • between your installation program in the My device and a PC through a USB Computer/Vodafone QuickStart path. • cable cannot be uninstall the software first. • between your device and a Ensure that the Wi-Fi function is enabled. • client through Wi-Fi cannot be If the driver of your device is abnormal, reinstall the software. You need to established.
Troubleshooting Problem Recommended Action The client • connected to the device cannot available. • access the Internet. Ensure that your (U)SIM card is Change the location and find a place with good signal. • Check the settings of the WAN connection mode. • Contact your service provider and confirm your APN settings. The 4G Mobile • Hotspot address is http://192.168.0.1 or configuration page cannot be Enter the correct address. The default http://vodafonemobile.wifi • visited.
This device has been tested and found to comply with the limits for a Class B digital device , pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage near the body with the separation of 10 mm.
For this device, the highest reported SAR value for near the body is 1.45 W/kg. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. SAR compliance for body operation is based on a separation distance of 10 mm between the unit and the human body. Carry this device, at least 10 mm away from your body to ensure RF exposure level compliant or lower to the reported level.
