R226-Z Quick Start Guide ZTE CORPORATION NO. 55, Hi-tech Road South, Shenzhen, P.R.
Getting to Know Your Device Appearance The following figure is for your reference only. 1. Power key 2. FUNC key 3. External antenna connector 4. LCD screen 5. micro-SIM card slot cover and reset hole 6. Charging/micro-USB jack 7.
Getting to Know Your Device Indicators When the device is powered on, the following icons may be displayed on the LCD screen. For a description of the icons, refer to the following table. Icon Description Network signal strength / / Network type The user is in roaming status. Connected to the Internet. Connected to the Internet in the Internet Wi-Fi mode.
Getting to Know Your Device Connection Scenarios The device can access the Internet in two ways and it allows multiple clients to surf on the Internet at the same time. The following figures are for your reference only. 4G Mode: A micro-SIM card can be used to access the Internet. Internet Wi-Fi Mode: Your device can be connected to a WLAN device (such as a hotspot device or wireless router) through Wi-Fi to access the Internet. The WLAN device must be already connected to the Internet.
Installing the micro-SIM Card 1. Open the micro-SIM card slot cover, and install a micro-SIM card to the micro-SIM card slot. NOTE: Do not remove the cover rudely, because it is connected with the device. WARNING! To avoid damage to the device, do not use any other kind of SIM cards, or any non-standard micro-SIM card cut from a SIM card. You can get a standard micro-SIM card from your service provider.
2. Close the micro-SIM card slot cover. Connecting to Your Device Using Wi-Fi 1. Power on your device. 2. Ensure that your computer or other client devices have enabled Wi-Fi, and search for available wireless networks. NOTE: Refer to your Wi-Fi-enabled client device manual for further details on how to search for wireless networks. If you use a computer, you need to set your computer to obtain an IP address automatically. 3. Select the Wi-Fi name (SSID) of your device, and click Connect. 4.
2. Power on your device. The operating system detects and identifies new hardware, and automatically installs the hardware. NOTE: If the system does not automatically launch installation, you can Double-click the device installation icon in My Computer to install the software. 3. Wait until the computer is connected to your device successfully. Getting to Know the Wi-Fi SSID and Password You can use the following methods to get the default Wi-Fi SSID and password. View the label on the device.
Logging in to the 4G Mobile Hotspot Configuration Page 1. Ensure that the connection between your device and the client device is correct. 2. Launch the Internet browser and enter http://192.168.0.1 or http://ufi.ztedevice.com in the address bar. 3. Enter the password to log in to the 4G Mobile Hotspot configuration page. NOTE: The default password is admin. Changing the Wi-Fi SSID or Password 1. Log in to the 4G Mobile Hotspot configuration page. 2.
Accessing the Internet 4G Mode After a client device is successfully connected to your device, you can access the Internet in Automatic or Manual mode. The default mode is Automatic. Mode Operation Automatic Your device is automatically connected to the Internet, and you can surf on the Internet through the client. Manual 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select Settings > Connection Mode > Manual, and then click Apply. 3.
Internet Wi-Fi Mode 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select Wi-Fi Settings > Internet Wi-Fi. 3. Set the Internet Wi-Fi Switch as Enable and then click Apply. 4. Set the Preferred Network as Wi-Fi and then click Apply. 5. Connect to the Wi-Fi hotspot. The following two methods are for your reference. Select a Wi-Fi hotspot listed in the Wi-Fi Hotspot area and click Connect. Enter a pass phrase in the Pass Phrase text box and click OK.
After the client device is connected to the Wi-Fi hotspot successfully, you can access the Internet. Using the FUNC Key When the screen is off, press the FUNC key to turn on the screen. When the screen is on, press the FUNC key to access the following options menu. or Wi-Fi QR code, activate WPS function, enable/disable global roaming or quick boot function without logging in to the 4G Mobile Hotspot Configuration Page. Data Connection You can connect or disconnect with the Internet 1.
Device Information You can view the device information. 1. Press the FUN key to show the options menu. 2. Press the FUN key to scroll to Device Info and then press the Power key. 3. Press the FUN key to see more information and then press the Power key to go back to the home screen. Wi-Fi QR code You can view the device’s Wi-Fi QR code. 1. Press the FUN key to show the options menu. 2. Press the FUN key to scroll to Wi-Fi QR code and then press the Power key. 3.
WPS You can activate the WPS function. 1. Press the FUN key to show the options menu. 2. Press the FUN key to scroll to WPS and then press the Power key. 3. Press the Power key to activate the WPS function. Global Roaming You can enable or disable global roaming. 1. Press the FUN key to show the options menu. 2. Press the FUN key to scroll to Global Roaming. 3. Press the Power key to enable or disable global roaming.
Quick Boot You can enable or disable quick boot function without logging in to the 4G Mobile Hotspot Configuration Page. 1. Press the FUN key to show the options menu. 2. Press the FUN key to scroll to Quick Boot. 3. Press the Power key to enable or disable quick boot.
Configuring Your PC The following describes how to configure the Internet Protocol in the Windows 7 operating system for your Wi-Fi connection. 1. Right-click Network and select Properties. 2. Select Change adapter settings. 3. Right-click Wireless Network Connection and select Properties. 4. Select Internet Protocol Version 4 (TCP/IPv4), and click Properties. 5. Select Obtain an IP address automatically and Obtain DNS server address automatically, and click OK.
• • • • • places such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Power off the device if necessary. Do not use electronic transmission devices in aircrafts, at petrol stations or in hospitals. Observe and obey all warning signs, and power off the device in these conditions. Do not touch the inner antenna area unless necessary. Otherwise the performance of the device may be affected.
• • • Handle the device carefully. Do not drop, bend or strike it. Otherwise the device may be damaged. Only qualified personnel can dismantle and repair the device. An operating temperature between -10°C and +60°C and humidity between 5% and 95% are recommended. Using Battery Do not change the built-in rechargeable battery in your device by yourself. The battery can only be changed by ZTE or ZTE authorized service provider.
above-mentioned situations. This warranty is end users’ sole remedy and ZTE’s sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the implied warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law.
Manual No.: FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States.
Display Grant section of www.fcc.gov/oet/ea/fccid searching on FCC ID: SRQ-R226-Z. after For this device, the highest reported SAR value for near the body is 1.19 W/kg. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. SAR compliance for body operation is based on a separation distance of 10 mm between the unit and the human body.
Troubleshooting Problem Recommended Action The connection Install the software, and run the installation program in the path of My between your device and a Computer. If the driver of your device is PC through a abnormal, reinstall the software. You USB need to uninstall the software first. cable cannot be established. The connection between your enabled. device and a client through Wi-Fi Refresh the network list and select the correct SSID.
Troubleshooting Problem The Recommended Action client connected to the device available. cannot access the Internet. Ensure that your micro-SIM card is Change the location and find a place with good signal. Check the settings of the WAN connection mode. Contact your service provider and confirm your APN settings. The client Ensure that the WLAN device has cannot access already been the Internet in Internet. Internet Wi-Fi mode.
Getting More Help You can get help by: • Sending an email to mobile@zte.com.cn • Visiting www.ztedevice.