LTE Indoor CPE User Guide FCC ID: SRQ-WF821
Index 1 2 3 Getting Started .......................................................................................................................... 5 1.1 Welcome to the CPE .................................................................................................. 5 1.2 Computer Configuration Requirements .................................................................... 5 1.3 Logging In to the Web Management Page ................................................................ 5 Overview ...
4 5 6 7 8 3.7.3 Delete Static Route .......................................................................................... 25 Wi‐Fi ........................................................................................................................................ 26 4.1 WLAN Setting .......................................................................................................... 26 4.1.1 Setting General Parameters.........................................................................
8.1 9 Maintenance ........................................................................................................... 46 8.1.1 Reboot ............................................................................................................. 46 8.1.2 Reset ................................................................................................................ 47 8.1.3 Backup Configuration File ............................................................................... 47 8.1.
1 Getting Started 1.1 Welcome to the CPE In this document, the LTE (Long Term Evolution) Indoor CPE (customer premises equipment) will be replaced by the CPE. Carefully read the following safety symbols to help you use your CPE safely and correctly: Additional information Optional methods or shortcuts for an action Potential problems or conventions that need to be specified 1.2 Computer Configuration Requirements For optimum performance, make sure your computer meets the following requirements.
2. Launch Internet Explorer, enter http://192.168.1.1 in the address bar, and press Enter. As shown in Figure 1‐1. Figure 1‐1 3. Enter the user name and password, and click Log In. You can log in to the web management page after the password is verified. As shown in Figure 1‐2. Figure 1‐2 The default user name is admin and the default password is olo@peru. To protect your CPE from unauthorized access, change the password after your first login. The CPE supports diagnostic function.
2 Overview 2.1 Viewing the System Information To view the System Information, perform the following steps: 1. Choose Overview; 2. In the System Information area, view the system status, such as Running time and Online time. As shown in Figure 2‐1. Figure 2‐1 2.2 Viewing the Version Information To view the Version Information, perform the following steps: 1. Choose Overview; 2. In the Version Information area, view the version information, such as Product name, Software version, UBoot version and so on.
2.3 Viewing CPU Usage To view the CPU usage, perform the following steps: 1. Choose Overview; 2. In the CPU Usage area, view the CPU usage information, such as Current CPU usage, Max CPU usage, Min CPU usage. As shown in Figure 2‐3. Figure 2‐3 2.4 Viewing Memory Usage To view the memory usage, perform the following steps: 1. Choose Overview; 2. In the Memory Usage area, view the memory usage information, such as Total memory, Current memory usage, Max memory usage and Min memory usage.
2. In the 4G Status area, view the information about USIM card status, Connect status, Operator, Current Mobile Network, Signal quality and so on. As shown in Figure 2‐5. Figure 2‐5 2.6 Viewing LAN Status To view the LAN status, perform the following steps: 1. Choose Overview; 2. In the LAN Status area, view the LAN status, such as Mac address, IP address and Subnet mask. As shown in Figure 2‐6. Figure 2‐6 2.7 Viewing Wi‐Fi Status To view the Wi‐Fi status, perform the following steps: 1.
2. In the Wi‐Fi Status area, view the information about Wi‐Fi status, SSID, Chanel NO., MAC address and WDS status. As shown in Figure 2‐7. Figure 2‐7 2.8 Viewing WAN Status To view the WAN status, perform the following steps: 1. Choose Overview; 2. In the WAN Status area, view the wan status, such as the DNS, Current data rate and the APN status. As shown in Figure 2‐8. Figure 2‐8 2.9 Viewing Throughput Statistics To view the throughput statistics, perform the following steps: 1. Choose Overview; 2.
Figure 2‐9 2.10Viewing Device List To view the device list, perform the following steps: 1. Choose Overview; 2. In the Device List area, view the device information which connect to the CPE, such as Device name, Mac address, IP address and Lease time. As shown in Figure 2‐10. Figure 2‐10 3 Network 3.1 WAN Settings 3.1.1 WAN Interface To set the WAN interface, perform the following steps: 1. Choose Network >WAN Settings; 2. In the Network Mode area, select an interface between LTE and Ethernet; 3.
Figure 3‐1 3.1.2 Network Mode To set the network mode, perform the following steps: 1. Choose Network >WAN Settings; 2. In the Network Mode area, select a mode between BRIDGE and NAT; 3. Click Submit. As shown in Figure 3‐2. Figure 3‐2 3.2 LTE Settings 3.2.1 Viewing Module Information To view the mobile module information, perform the following steps: 1. Choose Network > LTE Settings; 2.
Figure 3‐3 3.2.2 LTE Setting To set the LTE network, perform the following steps: 1. Choose Network >LTE Settings; 2. In the Setting area, you can set the configuration of LTE network; 3. In the LTE Settings area, you can view the LTE network connect status, such as Frequency, RSSI, RSRP, RSRQ, CINR, SINR, Cell ID and so on. As shown in Figure 3‐5.
Figure 3‐5 3.2.3 Connect Method Setting To set the connect method, perform the following steps: 1. Choose Network > LTE Settings; 2. In the Setting area, Select a connect method between Auto and Manual. As shown in Figure 3‐6.
Figure 3‐6 3.2.3.1 Auto Connect LTE Network To set the CPE automatically connect to the internet, perform the following steps: 1. Choose Network > LTE Settings; 2. In the Setting area, set the connect method as Auto, when the LTE network is ready, the CPE will be connected automaticity. As shown in Figure 3‐7.
Figure 3‐7 3.2.3.2 Manual Connect Mobile Network To set the mobile network manual connect to the internet, perform the following steps: 1. Choose Network > LTE Settings; 2. In the Setting area, set the connect method as Manual, when the LTE network is ready, you can set the CPE connect to the LTE network or disconnect from the LTE network. As shown in Figure 3‐8.
Figure 3‐8 3.3 APN Management 3.3.1 APN Settings in NAT mode To set and manage APN in NAT mode, perform the following steps: 1. Choose Network>APN Management. 2. In the APN Management area, you can set the APN. 3. Choose a APN number which you want to set. 4. In the APN Setting area you can set the APN parameters, such as enable or disable the apn, apn name, username, password and so on. 5. If you want set a APN as default gateway, you should check that is enabled.
6. 7. Select a APN type from the drop‐down list, such as VoIP, TR069 or VoIP+TR069. Click Submit. As shown in Figure 3‐9. Figure 3‐9 3.3.2 APN list To view the APN list, perform the following steps: 1. Choose Network>APN Management. 2. In the APN list area you can view the APN list. As shown in the figure 3‐11.
3.4 PIN Management To manage the PIN, you can perform the following operations on the PIN Management page: 1. Enable or disable the PIN verification. 2. Verify the PIN. 3. Change the PIN. 4. Set automatic verification of the PIN. As shown in Figure 3‐12. Figure 3‐12 3.4.1 Viewing the Status of the USIM Card To view the status of the USIM card, perform the following steps: 1. Choose Network >PIN Management. 2. View the status of the USIM card in the USIM card status field. 3.4.
3.4.3 Disabling PIN Verification To disable PIN verification, perform the following steps: 1. Choose Network >PIN Management. 2. Set PIN verification to Disable. 3. Enter the PIN (4 to 8 digits) in the Enter PIN box. 4. Click Submit. 3.4.4 Verifying the PIN If PIN verification is enabled but the PIN is not verified, the verification is required. To verify the PIN, perform the following steps: 1. Choose Network >PIN Management. 2. Enter the PIN (4 to 8 digits) in the PIN box. 3. Click Submit. 3.4.
3.4.7 Verifying the PUK If PIN verification is enabled and the PIN fails to be verified for three consecutive times, the PIN will be locked. In this case, you need to verify the PUK and change the PIN to unlock it. To verify the PUK, perform the following steps: 1. Choose Network> PIN Management. 2. Enter the PUK in the PUK box. 3. Enter a new PIN in the New PIN box. 4. Repeat the new PIN in the Confirm PIN box. 5. Click Submit. 3.5 LAN Setting 3.5.
3.5.2 Configuration the DHCP Server DHCP enables individual clients to automatically obtain TCP/IP configuration when the server powers on. You can configure the CPE as a DHCP server or disable it. When configured as a DHCP server, the CPE automatically provides the TCP/IP configuration for the LAN clients that support DHCP client capabilities. If DHCP server services are disabled, you must have another DHCP server on your LAN, or each client must be manually configured.
same IP address each time it accesses the DHCP server. For example, you can bind an IP address to an FTP server on the LAN. To add an item to the setup list, perform the following steps: 1. Choose Network Setting > LAN Settings. 2. Click Add list. 3. Set the MAC address and IP Address. 4. Click Submit. As shown in Figure 3‐15. Figure 3‐15 To modify an item in the setup list, perform the following steps: 1. Choose Network Setting > LAN Settings. 2. Choose the item to be modified, and click Edit. 3.
3.6 DMZ Settings If the demilitarized zone (DMZ) is enabled, the packets sent from the WAN are directly sent to a specified IP address on the LAN before being discarded by the firewall. To set DMZ, perform the following steps: 1. Choose Network Setting > DMZ Settings. 2. Set DMZ to Enable. 3. (Optional) Set ICMP Redirect to Enable. 4. Set Host address. This IP address must be different from the IP address set on the LAN Host Settings page, but they must be on the same network segment. 5. Click Submit.
Figure 3‐18 3.7.2 Modify Static Route To modify an access restriction rule, perform the following steps: 1. Choose Security>Static Route. 2. Choose the item to be modified, and click Edit. 3. Repeat steps 3 through 5 in the previous procedure. 4. Click Submit. As shown in Figure 3‐19. Figure 3‐19 3.7.3 Delete Static Route To delete a static route, perform the following steps: 1. Choose Security>Static Route. 2. Choose the item to be deleted, and click Delete.
4 Wi‐Fi 4.1 WLAN Setting This function enables you to configure the Wi‐Fi parameters. 4.1.1 Setting General Parameters To configure the general Wi‐Fi settings, perform the following steps: 1. Choose Wi‐Fi > Wi‐Fi Settings. 2. In the General Settings area, set WLAN to Enable. 3. Set Mode to one of the values described in the following table: Parameter Value Description 802.11b/g/n The Wi‐Fi client can connect to the CPE in 802.11b, 802.11g, or 802.11n mode. If the client connects to the CPE in 802.
Figure 4‐1 4.1.2 WPS Settings Wi‐Fi Protected Setup (WPS) enables you to simply add a wireless client to the network without needing to specifically configure the wireless settings, such as the SSID, security mode and passphrase. You can use either the WPS button or PIN to add the wireless client. To configure Wi‐Fi WPS settings, perform the following steps: 1. Choose Wi‐Fi > WPS Settings. 2. Set WPS to Enable. 3. Click Submit. As shown in Figure 4‐2. Figure 4‐2 4.
mode. This mode is recommended because it has a high security level. If Security is set to WPA‐PSK & WPA2‐PSK, Wi‐Fi clients connect to the CPE in WPA‐PSK&WPA2‐PSK encryption mode. 7. Set the encryption mode. If… Sets to Description WEP Authentication mode Shared authentication: The client connects to the CPE in shared authentication mode. Open authentication: The client connects to the CPE in open authentication mode. Both: The client connects to the CPE in shared or open authentication mode.
Figure 4‐3 4.3 Access Management 4.3.1 Setting the Access Policy This function enables you to set access restriction policies for each SSID to manage access to the CPE. To configure Wi‐Fi MAC control settings, perform the following steps: 1. Choose Wi‐Fi > Access Management. 2. In the WLAN Access List Settings area, set Access Policy. The access policy can be set to Disable, Blacklist or Whitelist. If SSID's MAC Access is set to Disable, access restrictions do not take effect.
To add an item to the Wi‐Fi access list, perform the following steps: 1. Choose Wi‐Fi > Access Management. 2. Click Add. 3. Set MAC address. 4. Click Submit. As shown in Figure 4‐5. Figure 4‐5 To modify an item in the Wi‐Fi access list, perform the following steps: 1. Choose Wi‐Fi > Access Management. 2. Click Edit MAC List. 3. Choose the item to be modified, and click Edit. 4. Set MAC address. 5. Set one of the SSID to Enable to make the MAC address take effect for the SSID. 6. Click Submit.
encryption mode to WPA/WPA2‐PSK, the Wi‐Fi clients can use WPA/WPA2‐PSK encryption mode. After WDS is enabled, disable DHCP on CPEs that are not directly connected to the WAN port. If WDS is enabled, the WPS function will not take effect. If the channel is set to Auto, you need to set the channel. To configure the WDS, perform the following steps: 1. Choose Wi‐Fi > WDS. 2. Set WDS to Enable. 3. Set WDS Mode as Repeater Mode; 4. Click Scan. From the search results, choose the SSID of the networking device.
5.1.1 Enabling MAC Filter To enable MAC address filter, perform the following steps: 1. Choose Security>MAC Filtering 2. Set MAC filtering to Enable. 3. Click Submit. As shown in Figure 5‐1. Figure 5‐1 5.1.2 Disabling MAC Filter To disable MAC address filter, perform the following steps: 1. Choose Security>MAC Filtering 2. Set MAC filtering to Disable. 3. Click Submit. As shown in Figure 5‐2. Figure 5‐2 5.1.
2. 3. Set Allow access network within the rules. Click Submit. As shown in Figure 5‐3. Figure 5‐3 5.1.4 Setting Deny access network within the rules To set deny access network within the rules, perform the following steps: 1. Choose Security>MAC Filtering. 2. Set Deny access network within the rules. 3. Click Submit. As shown in Figure 5‐4. Figure 5‐4 5.1.5 Adding MAC Filtering rule To add a MAC filtering rule, perform the following steps: 1. Choose Security>MAC Filtering. 2. Click Add list. 3.
Figure 5‐5 5.1.6 Modifying MAC Filtering rule To modify a MAC address rule, perform the following steps: 1. Choose Security>MAC Filtering. 2. Choose the rule to be modified, and click Edit. 3. Set MAC address. 4. Click Submit. As shown in Figure 5‐6. Figure 5‐6 5.1.7 Deleting MAC Filtering rule To delete a MAC address filter rule, perform the following steps: 1. Choose Security>MAC Filtering. 2. Choose the rule to be deleted, and click Delete. As shown in Figure 5‐7.
5.2 IP Filtering Data is filtered by IP address. This page enables you to configure the IP address filtering rules. 5.2.1 Enabling IP Filtering To enable IP Filtering, perform the following steps: 1. Choose Security>IP Filtering. 2. Set IP Filtering Enable. 3. Click Submit. As shown in Figure 5‐8. Figure 5‐8 5.2.2 Disabling IP Filtering To disable IP Filtering, perform the following steps: 1. Choose Security>IP Filtering. 2. Set IP Filtering Disable. 3. Click Submit. As shown in Figure 5‐9.
5.2.3 Setting Allow access network outside the rules To set allow access network, perform the following steps: 1. Choose Security>IP Filtering. 2. Set Allow access network outside the rules. 3. Click Submit. As shown in Figure 5‐10. Figure 5‐10 5.2.4 Setting Deny access network outside the rules To set allow access network, perform the following steps: 1. Choose Security>IP Filtering. 2. Set Deny access network outside the rules. 3. Click Submit. As shown in Figure 5‐11. Figure 5‐11 5.2.
2. 3. 4. 5. Click Add list. Set Service. Set Protocol. In the Source IP Address Range box, enter the source IP address or IP address segment to be filtered. 6. In the Source port range box, enter the source port or port segment to be filtered. 7. In the Destination IP Address Range box, enter the destination IP address or IP address segment to be filtered. 8. In the Destination port Range box, enter the destination port or port segment to be filtered. 9.
Figure 5‐13 5.2.7 Deleting IP Filtering rule To delete an IP address filtering rule, perform the following steps: 1. Choose Security > IP Filtering. 2. Choose the rule to be deleted, and click Delete. As shown in Figure 5‐14. Figure 5‐14 5.3 URL Filtering Data is filtered by uniform resource locator (URL). This page enables you to configure URL filtering rules. 5.3.1 Enabling URL Filtering To enable URL Filtering, perform the following steps: 3. Choose Security>URL Filtering. 4.
Figure 5‐15 5.3.2 Disabling URL Filtering To disable URL Filtering, perform the following steps: 1. Choose Security>URL Filtering. 2. Set URL Filtering to Disable. 3. Click Submit. As shown in Figure 5‐16. Figure 5‐16 5.3.3 Adding URL Filtering list To add a URL filtering list, perform the following steps: 1. Choose Security>URL Filtering. 2. Click Add list. 3. Set URL. 4. Click Submit. As shown in Figure 5‐17. Figure 5‐17 5.3.
1. 2. 3. 4. Choose Security>URL Filtering. Choose the rule to be modified, and click Edit. Set URL address. Click Submit. As shown in Figure 5‐18. Figure 5‐18 5.3.5 Deleting URL Filtering list To delete a URL list, perform the following steps: 1. Choose Security>URL Filtering. 2. Choose the item to be deleted, and click Delete. As shown in Figure 5‐19. Figure 5‐19 5.
6. Set Local host. This IP address must be different from the IP address that is set on the LAN Host Settings page, but they must be on the same network segment. 7. Set Local port. The port number ranges from 1 to 65535. 8. Click Submit. As shown in Figure 5‐20. Figure 5‐20 5.4.2 Modifying Port Forwarding rule To modify a port forwarding rule, perform the following steps: 1. Choose Security > Port Forwarding. 2. Choose the item to be modified, and click Edit. 3.
Figure 5‐21 5.4.3 Deleting Port Forwarding rule To delete a port forwarding rule, perform the following steps: 1. Choose Security > Port Forwarding. 2. Choose the item to be deleted, and click Delete. As shown in Figure 5‐22. Figure 5‐22 5.5 UPnP On this page, you can enable or disable the Universal Plug and Play (UPnP) function. To enable UPnP, perform the following steps: 1. Choose Security > UPnP. 2. Set UPnP to Enable. 3. Click Submit. As shown in Figure 5‐23.
Figure 5‐23 6 VPN Setting This function enables you to connect the virtual private network (VPN). To connect the VPN, perform the following steps: 1. Choose VPN Setting. 2. In the VPN Setting area, enable VPN. 3. Select a protocol from Protocol drop‐down list. 4. Enter Username and Password. 5. Click Submit. 6. You can view the status in VPN Status area. As shown in Figure 6‐1.
7.1 View VOIP Information To view VOIP information, perform the following steps: 1. Choose VOIP > VOIP Information; 2. View the VOIP information, such as the SIP account and status of the SIP registration server. As shown in Figure 7‐1. Figure 7‐1 7.2 Configuring SIP Server To set the SIP server parameters, perform the following steps: 1. Choose VOIP > SIP Server; 2. In the User Agent port box, enter the port of the SIP account provided by your service provider. 3.
Figure 7‐2 7.3 Configuring SIP Account Before configuring SIP accounts, make sure that the registration server has been properly configured. To configure SIP account, perform the following steps: 1. Choose VoIP > SIP Account. 2. Set SIP Account Enable. 3. In the User name and Password boxes, enter the user name and password of the SIP account provided by your service provider. 4. In the Phone Number box, enter the SIP Phone number provided by your service provider. 5.
Figure 7‐3 8 System 8.1 Maintenance 8.1.1 Reboot This function enables you to reboot the CPE. Settings take effect only after the CPE reboot. To reboot the CPE, perform the following steps: 1. Choose System>Maintenance. 2. Click Reboot. As shown in Figure 8‐1. The CPE then restarts.
8.1.2 Reset This function enables you to restore the CPE to its default settings. To restore the CPE, perform the following steps: 1. Choose System>Maintenance. 2. Click Reset. As shown in Figure 8‐2. The CPE is then restored to its default settings. Figure 8‐2 8.1.3 Backup Configuration File You can download the existing configuration file to back it up. To do so: 1. Choose System>Maintenance. 2. Click Download on the Maintenance page. 3.
The CPE uploads the backed up configuration file. The CPE then automatically restarts. Figure 8‐4 8.2 Version Manager This function enables you to upgrade the software version of the CPE to the latest version. It is recommended that you upgrade the software because the new version, certain bugs have been fixed and the system stability is usually improved. 8.2.1 Viewing Version Info To view the version info, perform the following steps: 1. Choose System>Version Manager. 2.
3. 4. 5. software version file. Click Open. The dialog box choses. The save path and name of the target software version file are displayed in the Update file field. Click Submit. The software upgrade starts. After the upgrade, the CPE automatically restarts and runs the new software version. As shown in Figure 8‐6. During an upgrade, do not power off the CPE or disconnect it from the computer. Figure 8‐6 8.
6. Set connection request user name and password. 7. Click Submit. As shown in Figure 8‐8. Figure 8‐7 8.4 Date & Time You can set the system time manually or synchronize it with the network. If you select Sync from network, the CPE regularly synchronizes the time with the specified Network Time Protocol (NTP) server. If you enable daylight saving time (DST), the CPE also adjusts the system time for DST. To set the date and time, perform the following steps: 1. Choose System > Date & Time. 2.
Figure 8‐8 To synchronize the time with the network, perform the following steps: 1. Choose System > Date & Time. 2. Select Sync from network. 3. From the Primary NTP server drop‐down list, select a server as the primary server for time synchronization. 4. From the Secondary NTP server drop‐down list, select a server as the IP address of the secondary server for time synchronization. 5. If you don’t want to use other NTP server, you need to enable Optional ntp server, and set a server IP address. 6.
8.5 DDNS Dynamic Domain Name Server (DDNS) service is used to map the user's dynamic IP address to a fixed DNS service. To configure DDNS settings, perform the following steps: 1. Choose System > DDNS. 2. Set DDNS to Enable. 3. In Service provider, choose DynDNS.org or oray.com. 4. Enter Domain name and Host name. For example, if the domain name provided by your service provider is test.customtest.dyndns.org, enter customtest.dyndns.org as Domain name, and test as Host name. 5. Enter User name and Password.
8.6 Diagnosis If the CPE is not functioning correctly, you can use the diagnosis tools on the Diagnosis page to preliminarily identify the problem so that actions can be taken to solve it. 8.6.1 Ping If the CPE fails to access the Internet, run the ping command to preliminarily identify the problem. To do so: 1. Choose System>Diagnosis. 2. In the Method area, select Ping. 3. Enter the domain name in the Target IP or domain field, for example, www.google.com. 4. Set Packet size and Timeout. 5.
Figure 8‐11 8.6.2 Traceroute If the CPE fails to access the Internet, run the Traceroute command to preliminarily identify the problem. To do so: 1. Choose System>Diagnosis. 2. In the Method area, select Traceroute. 3. Enter the domain name in the Target IP or domain field. For example, www.google.com. 4. Set Maximum hops ad Timeout. 5. Click Traceroute. As shown in Figure 8‐14. Wait until the traceroue command is executed. The execution results are displayed in the Results box.
Figure 8‐12 8.7 Syslog The syslog record user operations and key running events. 8.7.1 Local To set the syslog to local, perform the following steps: 1. Choose System>Syslog. 2. In the Setting area, set the method to Local. 3. In the Level drop‐down list, select a log level. 4. Click Submit. As shown in Figure 8‐15.
Figure 8‐13 Viewing local syslog To view the local syslog, perform the following steps: 1. In the Keyword box, set a keyword. 2. Click Pull, the result box will display. 8.7.2 Network To set the syslog to network, perform the following steps: 1. Choose System>Syslog. 2. In the Setting area, set the method to Network. 3. In the Level drop‐down list, select a log level. 4. In the Forward IP address box, set a IP address. 5. Click Submit. As shown in Figure 8‐16.
Figure 8‐14 8.8 Account This function enables you to change the login password of the user. After the password changes, enter the new password the next time you login. To change the password, perform the following steps: 1. Choose System>Account. 2. Select the user name, if you want to change the password of normal user, you need to set Enable User enable. 3. Enter the current password, set a new password ,and confirm the new password. 4. New password and Confirm password must contain 5 to 15 characters.
Figure 8‐15 8.9 Remote WEB Access To configure the parameters of WEB, perform the following steps: 1. Choose System> Remote WEB Access. 2. Set HTTP enable. If you set HTTP disable, you will can’t login the web management page with the HTTP protocol from WAN side. 3. Set HTTP port. If you want to change the login port, you can set a new port in the box, the default HTTP port is 80. 4. Set HTTPS enable.
Figure 8‐16 8.10Logout To logout the web management page, perform the following steps: 1. Choose System and click Logout 2. It will back to the login page. 9 FAQs The POWER indicator does not turn on. Make sure that the power cable is connected properly and the CPE is powered on. Make sure that the power adapter is compatible with the CPE. Fails to Log in to the web management page. Make sure that the CPE is started.
Check that the CPE is placed far away from household electrical appliances that generate strong electromagnetic field, such as microwave ovens, refrigerators, and satellite dishes. If the problem persists, contact authorized local service suppliers. The power adapter of the CPE is overheated. The CPE will be overheated after being used for a long time. Therefore, power off the CPE when you are not using it. Check that the CPE is properly ventilated and shielded from direct sunlight.
FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. The antennas must not be co‐located with other transmitter antennas. The device can only operate indoor, and can not operate in outdoor condition.
