ZTE AC570 EVDO USB Modem User Guide 1
Contents 1 Modem Introduction....................................................4 1.1 Introduction....................................................... 4 1.2 Warning and Notice ........................................ 4 1.3 Applicability Scope ......................................... 6 1.4 System requirements ..................................... 6 1.5 Functions ........................................................... 6 1.6 Specification.....................................................
.4 Phonebook ....................................................... 26 3.5 Settings ............................................................ 28 3.5.1 Network Settings...................................................29 3.5.2 Security Settings....................................................31 3.5.3 Network Settings...................................................32 3.5.4 Messages Settings .................................................33 3.5.5 Alert settings ...................................
1 Modem Introduction 1.1 Introduction Thank you for using ZTE MY69 USB Modem. To guarantee the modem always in its best condition, please read this manual carefully and keep it for further use. The pictures, symbols and contents in this manual are just for your reference. They might not be completely identical with your modem. We operate a policy of continuous development. We reserve the right to update the technical specifications in this document at any time without prior notice.
injury if used as a toy. Modem Please use original accessories or accessories that are authorized. Using any unauthorized accessories may affect your modem’s performance, and violate related national regulations about telecom terminals. Avoid using the modem near metallic structure device or establishment that can emit electromagnet wave. Otherwise it may influence receiving signals. The modem is non-waterproof type, please keep it dry and store in shady and cool place.
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver.
1.6 Specification Networks Frequency Band CDMA 2000 1x / EVDO CDMA 800MHz Cellular (UL824~849,DL869~894) CDMA 1900MHz PCS (UL1850~1910,DL1930~1990) Dimension Weight Data Rate Working Voltage 90.4mm*35mm*12.3mm About 35.2g Up to 3.
2 Installation 2.1 Outline and Part Introduction 1. USB Interface 2. UIM Card Slot 3. Indicator 4. Antenna 4 3 2 1 4 Indicator Light Status: Indicator Green/Lighting Red Green/Blink Green/Blink three times Status Normal. Abnormal/No network signal. An Incoming Call. A New Message. 2.2 Software Installation The system will automatically detect and recognize the new hardware and display the new icon in the desktop status bar, indicating that the computer and the USB Modem have been connected properly.
If the notebook PC doesn’t support automatic installation, you can run the installation program in path of My Computer → ZTEMODEM → AutoRun.exe. The following installation interface will show how to start installation. Select PENDRIVE, use the modem as U-Disk. step. Select MODEM, go to next Recommend you to exit other “Windows” programs, and click “Next”.
Read the agreement carefully. If you agree, choose “I agree to the terms of this license agreement”, and then click “Next”. Select the folder that you want to install the software. You can select a different path by pressing “Change”, and then click “Next”.
Installation is in progress, after a while, there will be a tip as follows: Click “Finish” to finish the software installation.
contact the service provider for help. After the installation, select “Start” menu → “Programs” and there will be a “ZTE Mobile Connection” program group listed in, which includes “ZTE Mobile Connection” and “ZTE Uninstall”, and a shortcut icon on the desktop is also created. 2.3 Hardware Installation 1. Insert the UIM card into the modem: First, you should insert your UIM card into the USB modem, and confirm that your UIM card support data and CDMA services.
the installation program will start automatically. Note: For Microsoft Vista system, to avoid abnormal installation it is suggested to turn off UAC before installation following the path of Start→ Control Panel→ User Accounts→ Turn User Account Control On or Off. Restart your computer when you finish settings. 3. Antenna When using the Modem, in order to get the good signals, please open the antenna upright. 2.
Click “Yes” according to the indication, then the system begins to uninstall programs, wait a moment and the following screen will appear: Click “Finish” and complete the application software uninstall. 2.7 USB Disk Function You can use your modem as a removable USB disk. When you insert your modem into portable PC, the system will automatically detect and recognize the new hardware. After a few seconds, the following window appears.
Note: if the system doesn’t launch the window automatically, you can run My Computer > ZTEMODEM > AutoRun.exe. Select PENDRIVE icon. The system will install the driver automatically. After a few seconds, a removable disk will appear in My Computer, and then you can use it. If you want to stop using the USB disk and remove the disk safely, click the new hardware icon disk safely.
3 Functions & Operation 3.1 Interface introduction 3.1.1 Main Interface The diagrams drawing for the main interface of USB modem application software: Function Button Area System Information Area User Area The whole interface is divided into three parts, related functions can be executed by operation in the corresponding areas. 1. Function button area: There will show various function button icons. Select different function button and it will carry out corresponding operation.
SMS: Send SMS or read SMS Inbox. Phonebook: Save and view different information of the contact list. Settings: Set normal relative information for the modem. Call Records: View related information for all calls. UTK: Supported the service provided by service provider. GPS: Support the GPS service. . 2. System information area: Show the system status and different kinds of tips. Shows network signal intensity, 5 stages from none to strong . There are new SMS at present.
3.1.2 Description of Mini Icons When click the mini button, the software will minimize as an icon on the system tray. If connected to the Internet, the minimized software won’t influence the download of data or receiving SMS. 1. Taskbar Icons’ Description Modem is in normal standby status. Green indicates already connecting of modem with PC. Orange indicates modem offline. Red indicates disconnecting of modem with PC. Red indicates no UIM card in the modem. No network signal. New Message.
Modem Offline/ Modem Online: Pause/reusing the working of the modem. If connected Internet, you need disconnect the Internet first, and then select the Modem Offline. Factory Settings: Restore the factory setting. Help: Enter Help interface. About: View the information of the application software and hardware versions. Exit: Close the application interface and stop using the modem. 3.
through network. During the course of connecting, when the “Connect” 'button becomes “Disconnect” button, you can cancel the connecting. At the same time, an icon on taskbar appears indicating network connection. Then you can access Internet and receive email etc. via network. 2. Disconnect the Internet Click “Disconnect” button to disconnect Internet. After disconnection, a normal standby icon appears on taskbar. 3.3 Dialing/Answering a call Click the “Calls” icon , and switch to the calls interface.
1. Making a call： Click the number button in the right interface, or enter the phone number by typing the keyboard of computer. Press to send and press to end. Press to erase input character. For international long distance phone call, quick press international prefix “+”, phone number, quick press enter character “P” which stands for pause 3 seconds. 2.
4. Redialing： In standby status，press to switch to the dialed calls list, select the number and press and click “Dial” button. 5. Emergency call： Even without UIM card inserting, you still can dial up emergency calls. 6. Dialing up when surfing on the Internet： When surf on Internet, you also can dial up if network supports. Click “Calls” icon to enter calls interface and make calls. 7. Viewing missed calls： If there is missed call, icon icon to enter calls list to view.
InBox: Save the received SMS. OutBox: Save the successfully sent SMS. Draft box: Save the editing SMS, which haven’t been sent. The drafts can only be saved in PC side. For example: “Message in InBox PC :1 Item(s) UIM Card 4 Item(s)” means: The PC side has 1 short message and there are 4 short messages in the Inbox of the UIM card , “UIM Card capability” means the UIM can hold 40 short messages. Different UIM cards will have different capacities. For more information, please consult your supplier.
3.4.2 Create new message Click “New Message” button to input the recipient’s number and content. The recipient’s number can be input directly or entering the phonebook by . pressing The recipient’s amount can be one or more. Please use “;” to separate recipients. The SMS content can include 160 individual English characters (including English symbols). On the interface, there will show total characters.
Select Yes, the SMS will be send, select No, you will go back to previous step to edit the information. After sent successfully, the SMS will be saved into outbox automatically. If send fails, it will be saved to the draft box automatically. Send SMS when browsing the web: When surfing the Internet, if your network supports, you can send short messages. Click “SMS” button icon, enter the short message interface to send short messages normally.
3.4.3 The SMS box Operating Guide Enter any of Inbox/Outbox/Draftbox to execute the following functions: Read: Read all the information of short messages. (The content of short messages, sender’s phone number, sending time and date) Reply: Reply short messages to the sender (Can’t be executed in OutBox / DraftBox). Forward: Forward short message to other recipients (Can’t be executed in DraftBox). Move: Change the saving location of short messages between PC or UIM card (Can’t be executed in DraftBox).
1. New Contact Click “Add” →”New Contact”, input the content, then select “OK” to finish adding a new contact. 2. New Group You can add new groups at the PC side. But you cannot add new groups at the UIM side. Click the “Add” →”Add Group” and input the group name in PC group folder tree.
3. Other buttons Description If any contact or group is selected, you can carry out the following steps: View: View the information of selected contact. New: Add the new contact. Delete: Delete the selected contacts. SMS: Send messages to the mobile phone numbers in the records. Save As: Save the contacts in PC. Edit: Edit the information of selected contacts. Dial: Call the contact. 3.5 Settings Click “Settings” icon to switch to the settings interface.
3.5.1 Network Settings To ensure that the modem can connect the Internet properly, you should configure the user configuration information first. You can save the different supplier’s network configurations as different files. 1. Button Description Add: Add new configuration files. Delete: Delete the selected configuration files. Edit: Edit the selected configuration files. Set Default: Select one file from filename list, and set it as the current using files.
2. Config File The user configuration information includes: Config filename, Dial Number,User name, Password, PDP Type, Authentication Mode, DNS, and PDP address. If network supports “Obtain server address automatically”, the modem can obtain the assigned IP information automatically. If network does not support it, you should input the proper address manually. Please consult the network supplier of UIM card for all above information.
3.5.2 Security Settings The interface shows as the following picture： 1. Enable the PIN Code When “PIN enable” item is selected, please enter PIN code to use the modem and you can click “Revise PIN” to modify the number. Note: This function need network support. 2. Backup Phonebook SMS and Internet connection records Click “Backup” to backup the Phonebook, SMS and Internet connection records in portable PC. Click “Resume” to restore the backup data. You need restart the software.
3.5.3 Network Settings Select Mode preference, EVDO+CDMA 1x, CDMA 1X Only, or EVDO Only. For detail information, please consult with your service provider.
3.5.4 Messages Settings Validity period: Set the time limit for saving SMS in the network side. (This function needs network supports.)In option：an hour/12 hours/A day/A week/The longest period. Delivery Report: Set as “Turn On” or “Turn Off”. When it is set as “Turn On”, the network will inform you when you sent messages successfully. Location of Saving New SMS: Select “UIM Card” to save in UIM card; select “PC” to save in PC. 3.5.
3.6 Call History There are Missed Calls, Received Calls and Dialed Calls in Call History. Select one to enter, you can see the details information.
Dial: Call the number. SMS: Send messages to the number. Edit: Edit the information of selected number. Delete: Delete the selected number. Clear: Clear all numbers. 3.7 UTK Click UTK icon, switch to the UTK interface. This function needs network support by service provider. If you UIM card can also support, menu of UTK appears on the display. If UIM Card and network provider do not support, the function is invalid. The application of this function may ask for extra fee.
The modem will make the position and show the results. After finish the position, you can press the Show Map to show the map of your position from Google.
3.8.2 User Settings 1. 2. Operation Mode Network only: get position results directly via CDMA network and PDE sever. MS-based: firstly get basic position data via CDMA network and PDE sever firstly, then the modem make the calculation and get the position results. Standalone: get the position results not via CDMA network. Fix Rate Number of fixes: Set the maximum number of position in Track Mode. Time between fixes: Set the time interval in Track Mode. 3.8.3 Restore Default Restore to factory setting.
4 FAQ & Answers When you meet the following problems in service, please refer to the following answers to solve it. If the problems still exist, please contact with your suppliers. Problem Description The system can not run the installation program automatically Possible Causes The system configuration is not suitable for the auto-run. After the full installation, the system doesn’t install the driver program properly. The system configuration is not suitable for the auto-run.
When the USB modem has been plugged in, computer cannot find the visual disc of the USB modem. 2．You are in the place where no CDMA network covered , such as underground parking lot, tunnel etc. 2. Move to the place that has good signal. 1. You have not installed the USB modem properly. 1. Run the installation program first, then insert the modem. If you use the WinXP operating system, install the drivers according to the Windows indication information to operate. 2.
2. The network at this time in this place is busy now. 3. The modem data is error. Connected to the Internet, but it cannot open any website page. 1. After connection, there is no data transfer, which resulted that you can not open web pages. 2. The IE browser got problems. The Modem cannot connect to the Internet in other places 3. The operating system is infected by virus (Such as Worm.
No warning tone problems.) No audio card is fixed in computer or the volume is too small. 42 Check the audio card and adjust the volume properly.
