ZTE MF335 HSDPA/EDGE Card User Manual
Copyright © 2007 by ZTE Corporation All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written authorization of ZTE Corporation. st Edition: 1 edition, Sep., 2007 .
Contents 1 Wireless Data Card Introduction...................................................... 1 1.1 Introduction ............................................................................... 1 1.2 Safety Warning and Notices...................................................... 2 1.3 Systems Supported................................................................... 3 1.4 PC System Requirements......................................................... 4 1.5 Data Card Technical Specification.............
1 Wireless Data Card Introduction 1.1 Introduction Thank you for choosing the ZTE MF335 HSDPA/EDGE Card. To help you use your card please read the manual carefully and keep it for reference. The pictures, symbols and contents in this manual are for reference only. They might not be completely identical to your card. Please refer to the actual device. The manufacturer operates a policy of continuous development.
1.2 Safety Warning and Notices To the owner z The use of electronic transmitting devices is forbidden in aircraft, at petrol stations and in hospitals. Please observe and obey all warning signs and switch off your PC in these conditions. z Operating a portable PC and data card may interfere with medical devices like hearing aids and pacemakers. z Be aware of warning signs in places such as oil refineries or chemical factories where there are explosive gases or explosive products being processed.
z This data card generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. z There is no guarantee that interference will not occur in a particular installation.
PCs such as HP, Compaq, IBM, Toshiba, LG, Dell, etc. 1.4 PC System Requirements The data card and software application supports Windows 2000, XP and Vista only with recommended specification: CPU Pentium III or above Hard Disk 20G or above RAM 128M or above 1.
2 Installation 2.1 Unpacking Check the following items are included in the package: ZTE MF335 HSDPA/EDGE Card, Headset, Software CD, Quick Start Guide and Warranty Card. 2.2 Appearance and Parts 1 2 3 1. Headset Jack 2. Indicator 3. Express Interface LED Indicator Status: LED Status Green On Normal Red On Abnormal / No network signal Green flashing Incoming Call Green blinks four times New SMS Message 2.3 Software Installation Install the software before inserting your card into your PC.
If the PC doesn’t launch the installation automatically please run on the CD. Choose Setup Language, and then click OK to continue. Click Next to continue.
Select “I accept…” and click Next to continue. You can change the installation folder by pressing Change, and then click Next to continue.
Installation is in progress. Click Finish to complete the software installation. 2.
insert the data card into the PC slot and allow Windows to complete the New Hardware Installation. Launch the application software by double-clicking on the desktop icon or select Start → Programs → BANDA ANCHA DE TELCEL → BANDA ANCHA DE TELCEL. 2.
2.6 Software Uninstallation Process If you need to uninstall the software first close the application program then click Start → Programs → BANDA ANCHA DE TELCEL → Uninstall. Follow the prompts on screen: Click Yes to continue. Remove the Data Card from PC, and then click Yes to continue.
Click Finish and complete the application software removal. 2.7 Hardware Set Up First install the CD Software See 2.3 above. 1. Inserting SIM/USIM card into the data card Before inserting the data card into your PC you need to fit your SIM/USIM card. Insert the SIM/USIM card with the gold contacts facing downwards into the slot on the side of the data card. 2. Inserting data card into your PC Insert the data card into the EXPRESS slot and push firmly home.
3 Using the Software Application 3.1 Software Introduction Launch the software by double clicking on the desktop icon. The connect interface is displayed: Functions Area System Information Area User Area Press Connect to connect to the default service. The screen is divided into three sections. The top section contains the function buttons for quick connection, messages and set up. The next bar contains network and card status and is called the System Information Area.
1. Functions Area: The function buttons are straight forward and intuitive providing quick access to the most common features of the data card. Connect to the Internet Dial or receive a call.
2. System Information Area The system information area reports the status of the data card, signal strength, missed calls, messages etc. Network signal strength indicator. You have incoming call or missed calls There are new SMS messages Data card disconnected from the Internet Data card connected to the Internet SIM/USIM card is roaming P indicates packet-switched service.
System Information - Minimized Icons on task bar When the window is minimized, the system icons display on the taskbar. Double click the icon to re-size the display. 1. Taskbar Icons’ Description Data card has been inserted into the computer. Data card has not been inserted into the computer. Data card is offline. SIM/USIM card has not been inserted or the SIM/USIM card is not correct. Data card is working normally, idle status. No network signal. New Message. New incoming call or missed calls.
About: View application software and hardware versions. Exit: Close the application interface and stop using the data card. 3.2 Connecting to the Internet Click the Internet icon and press Connect to confirm. Notes • For connecting to the Internet, you should set the right profile file at first. See 3.9 section 1. • Once you are connected, run Internet Explorer or other applications in the usual way. • You can still receive and make calls while you are connected to the net.
• Press Disconnect to terminate the connection. 3.3 Making a Call Connect your headset and click the Calls icon to make a call. Enter the telephone number using the keypad on the screen or by typing on the keyboard. You can also select numbers from the calls list or from your contacts. Notes • If you make a mistake press • Press • For international calls, press to clear. to send and press 17 to end a call.
prefix “+”. 3.4 Answering an Incoming Call When you get an incoming call “Incoming Call” appears on the screen and an alert will ring on the PC. The incoming number (if available) will show in the left and the green light on the data card flashes continually. Press to answer or press to reject. You can also press the button on the headset to answer the call. 3.5 Other Call Functions 1. Volume Adjustment: You can adjust the headphone volume by using the slider . 2.
3.6 SMS Messages Click the SMS icon to use the SMS interface. Then click on the respective button to view: InBox: Contains received SMS messages. OutBox: Contains sent SMS messages. DraftBox: Contains draft messages and messages that failed to send. After clicking on the respective box use the buttons at the bottom of the window to Read, Reply, Forward, Move, Delete, Save or Cancel message(s). 3.7 Create a New Message Click New Message.
from your contacts by pressing . Type your message then click Send and follow the prompts. After sending the SMS will be saved in the OutBox. If it fails to send the message will be saved in the Draft Box. Notes • • SMS messages are limited to 765 characters including spaces etc. You can send messages while using the internet. Just click on the SMS icon and create a new message as above. • You can add multiple recipients using “;” between each number.
arrow button to move it to the right box. When you press OK the contacts will show in the new message window. 3.8 Phone Book Click the Phone Book icon to use the phone book interface. The Folder window indicates if the contacts are stored on the PC or the SIM/USIM card. 1. To Add a New Contact Click New, New Contact. Enter the required information then select OK to finish.
2. New Groups Contacts can be stored in different groups. You can create and name your own groups using the New Group button. 3. Searching and Editing Records Type any part of the record into the entry bar and click Search. When a record is selected you can View, Delete, SMS, Save as, Edit or Dial the selected record using the corresponding buttons.
4. Copying contacts from SIM/USIM card to PC Use the check boxes to select your required contact on the SIM/USIM card then drag them up to the folder section and drop them on PC. The highlighted contacts will be copied from the card to the PC. 3.9 Settings Click the Settings icon to use the settings interface.
1. Connection Settings There is one default profile provided by service provider in the settings configuration. You can view the details and set it as the default file. Consult service provider for more details. For other profile, you can Add, Delete, Edit, and Set default.
2. Security Settings • PIN Enable, Change PIN – Enable PIN protection and change your PIN Number. • Backup Phone Book, Call records, Internet connection records and SMS – Store and restore back-ups on your PC. Notes The PIN number for the card is provided by service provider. If you change or lock up your PIN number you will need to contact service provider to get a PUK code.
3. Network Settings The network selection can be set to Automatic or Manual. When you select Manual the card will search and display available networks.
Notes • • It is best to leave the default settings on automatic. The software will negotiate the best available connection depending on your network coverage. Select International Roaming to enable use on overseas networks. 4. Message Settings You can set the Message Center number (preset, no need to change) and change the Validity Period, SMS Save Location and Delivery Report. Note: When delivery report is turned on you get a message back from the message center confirming when your SMS is delivered.
5. Alert settings You can set different sounds or mute each alert for Connect alert, Disconnect alert, Incoming SMS alert and Incoming call alert on the PC. Use Browse to select alternative sounds. 6. Factory settings If you change any of your settings and manage to disable your connection please try the factory settings button on the task bar. Move your mouse over the icon on the task bar and right click to select the Factory Settings option.
3.10 Call Records Click the Call Records icon to use the call records interface. When a record is selected you can Dial, send SMS, Save, and Delete. Use the Clear button to clear all records. Note When more than 50 records are exceeded the system automatically deletes old records. 3.11 Help Click Help icon to switch to the help interface. Under Help you can get an introduction to the data card functions, installation and usage guide.
4 FAQ & Answers If you experience any problems with your data card please check the FAQ section below. If the problems still exists consult your service provider or ring the customer service number on the warranty card. If the card or the software are not responding first switch the card off line, then remove and re-insert your card, close and restart the software application. Finally try rebooting the PC. Description After restarting the PC, there is still no signal.
Description Data connection fails. Possible reasons You are in an area where there is no or poor network coverage such as deep in a building or underground in a car park etc. The network is busy. The dialed number or the APN in the user config files is incorrect. The HSDPA/EDGE data fails. The manual configurations are set wrong. Connected to the Internet, but cannot open any web pages. Cannot use the data card after deleting some hardware. After connection, there is no data transfer.
Description Possible reasons Solution The window disappears when you minimize it. This is normal. The application is still running in the background and can be accessed through the task bar. Double click the icon on the task bar to re-size the window. Incoming call does not show phone number. The incoming call has blocked their number, or the network does not support this. Problem is with the other party or the network. No warning tones.
5 Environmental Statement ZTE is committed to saving and protecting the natural environment and asks you to continue this commitment when you dispose of your equipment. Your ZTE MF335 HSDPA/EDGE Card is made using the latest manufacturing techniques and environmental standards to reduce waste and hazards to the environment.
