ZXDSL 831/831B/831Ⅱ/831BⅡ User’s Manual Document version: 20080813-R2.2 Copyright 2006 ZTE Corporation All rights reserved. No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any means without the prior written permission of ZTE Corporation. ZTE CORPORATION reserves the right to modify this manual for product upgrade or other causes without notifying users in advance.
Limited warranty ZTE warrants that, for one year from the date of delivery by ZTE to purchaser's designated carrier, the Equipment will remain free from defects in design, material and workmanship under normal use and service and will conform in all material respects to the applicable specifications set forth in purchase order or agreement; ZTE does not warrant that operation of the Equipment will be error-free or uninterrupted.
ZXDSL 831/831B/831II/831BII User’s Manual procedures; provided that if End User causes or permits services to be provided by individuals who are not ZTE-certified, the Warranty shall be void as to all Equipment serviced in breach of this sentence. End User shall have no right to reject, return, or receive a refund for any Equipment from ZTE.
ZXDSL 831/831B/831II/831BII User’s Manual TO, LOST PROFITS, COST OF CAPITAL, COST OF SUBSTITUTE FACILITIES OR EQUIPMENT, ANY DOWNTIME COSTS OR CLAIMS OF END USERS.
Contents Chapter 1 Safety Guidance............................................................1 1.1 Safety Check......................................................................................... 1 1.2 Safety Cautions..................................................................................... 1 Chapter 2 Overview .......................................................................3 2.1 Features................................................................................................
Chapter 1 Safety Guidance 1.1 Safety Check Before installing the ZXDSL 831/831B/831II/831BII ADSL equipment, you must check the following items. 1 Electric safety z Ensure that there are no inflammable, conductive or moist objects around. Check whether the cables are aged and whether other electrical appliances are placed stably. 2 Equipment position z Because the running electric devices easily generate heat, please ensure that these devices are positioned in a well ventilated environment.
ZXDSL 831/831B/831II/831BII User’s Manual z Rather than directly connecting phones to the ADSL line, led them out from the phone interface of the splitter. z Never place any objects on the equipment. z Keep the equipment dry, ventilated and rainproof, and clean. z Unplug the power and all connection cables in case of thunderstorms, to protect the equipment against lightning. z Clean the equipment using a soft and dry cloth rather than liquid or atomizers.
Chapter 2 Overview The ZXDSL 831/831B/831II/831BII is an ADSL access device that allows multiple line transmission modes. The equipment provides a 10/100Base-T Ethernet interface in a local LAN device. Through the high-speed ADSL access service, the ZXDSL 831/831B/831II/831BII can provide the broadband Internet service or enterprise network access service for users. This device complies with part 15 of the FCC Rules.
ZXDSL 831/831B/831II/831BII User’s Manual 2.
ZXDSL 831/831B/831II/831BII User’s Manual z Instant plug and instant use, with no configuration required z Supporting 64 PVCs z Supporting the Bridge mode 2.
ZXDSL 831/831B/831II/831BII User’s Manual 2.3 Package Check z ZXDSL 831/831B/831II/ 831BII ADSL MODEM ×1 z Splitter ×1 z Power Adapter ×1 z RJ-11 telephone cable ×2 z RJ-45 Ethernet cable ×1 z User’s Manual ×1 z Quality Warranty Card ×1 z Certificate of Quality ×1 z CD (Optional) ×1 Note: for your information only, please refer to the actual product. Note: Please use a power adapter that matches the ZXDSL 831/831B/831II/ 831BII package. 2.
ZXDSL 831/831B/831II/831BII User’s Manual Please make sure that the system has been equipped with the 10M/100M Ethernet adapter and supports the TCP/IP protocol. Because ADSL can be used for broadband access and involves a wide range of multimedia services, you are recommended use a computer with such configurations as: above PentiumIII, 64 M memory, 10 G hard disk, graphic accelerating adapter with above 2 M display memory, audio adapter and sound box.
Chapter 3 Installation Preparation 3.1 Hardware Description Front panel Power DSL Internet Ethernet Figure 3.1-1 Front Panel of the ZXDSL 831/831B/831II/831BII Table 3.1-1 Descriptions of the LEDs on the Front Panel LED No. Power DSL Color Status Off Green/Red Red Flash Green On Off Green Flash On Off Flash Internet* Green On Off Ethernet Green Flash On Note Power off Software upgrade.
ZXDSL 831/831B/831II/831BII User’s Manual Rear panel Figure 3.1-2 Rear Panel of the ZXDSL 831/831B/831II/831BII Table 3.1-2 Description of Interfaces on the Rear Panel Item DSL Reset Ethernet PWR Introduction RJ-11 connection interface: The equipment is connected to the ADSL line or splitter via the telephone line. In the power-on state, you can restore the system to the default configuration by using a thin needle to press this slot for three seconds or for three executive times.
ZXDSL 831/831B/831II/831BII User’s Manual Reset Ethernet DSL ADSL service Splitter MODEM socket LINE RJ-11 PWR RJ-45 Power adapter PHONE TelephoneTelephone Power socket PC Figure 3.2-1 ZXDSL 831/831B/831II/831BII Connection Schematic Diagram (No Phone sets are installed before the Splitter) Connection 2 Figure 3.2-2 shows the connection when the splitter is installed near the ZXDSL 831/831B/831II/831BII.
ZXDSL 831/831B/831II/831BII User’s Manual Note: In the circumstance where the first connection example is not applicable and you choose to use the second example, you must install a MicroFilter on the telephone cable (as illustrated in Figure 3.3-2, do not use a splitter to replace the MicroFilter).
ZXDSL 831/831B/831II/831BII User’s Manual using the RJ-11 telephone cable, connect the phone set lines to the PHONE interface of the splitter, and then connect the user telephone cable port to the LINE interface of the splitter. 4 Connect the power Connect one terminal of the power adapter to the PWR interface of the ZXDSL 831/831B/831II/831BII, and the other terminal to the socket on the wall, and then switch on the power of the ZXDSL 831/831B/831II/831BII equipment.
Appendix A FAQs 1 All indicators are off after the ZXDSL 831/831B/831II/831BII equipment is powered on First make sure that you have inserted the power adapter of the ZXDSL 831/831B/831II/831BII into a working power socket and that the ZXDSL 831/831B/831II/831BII has been powered on (the switch button is pressed down). If the indicators are still off after confirmation of the above items, the hardware is damaged probably. You may contact local operators for maintenance.
ZXDSL 831/831B/831II/831BII User’s Manual 5 Password verification failure MODEM synchronization and connection are normal. However, sometimes the password fails to be verified. 1. Note that the account and password are case sensitive and some accounts contain a domain name. 2. Virtual dialup software. It is possible that sometimes the virtual dialup software is faulty, or conflict with other software in the operating system.
ZXDSL 831/831B/831II/831BII User’s Manual 7 The authenticated user names and passwords cannot be re-authenticated? This problem may be due to the following reasons: 1. Your account has expired or you are a defaulting subscriber (please pay the deficit sum). 2. You move into a new area. Because the account and the path PVC are bundled by some operators, your previous account and password cannot be authenticated after you changed your path. 3. One of your accounts has logged on successfully.
Appendix B Standard Compliance 1 The equipment complies with the following ADSL standards: Standard ANSI T1.413 Issue 2 ITU G.992.1 Annex A ITU G.992.2 Annex A ITU G.992.3 Annex A ITU G.992.3 Annex L ITU G.992.5 Annex A ITU G.994.1 2 Note Only supported by the ZXDSL 831II/831BII Only supported by the ZXDSL 831II/831BII Only supported by the ZXDSL 831II/831BII ZTE’s equipment complies with the following national standards of the PRC: Standard No.