ZXDSL 831AⅡ User’s Manual Document version: 201004012-R3.1 Copyright 2006 ZTE Corporation All rights reserved. No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any means without the prior written permission of ZTE Corporation. ZTE CORPORATION reserves the right to modify this manual for product upgrade or other causes without notifying users in advance.
Limited warranty ZTE warrants that, for one year from the date of delivery by ZTE to purchaser's designated carrier, the Equipment will remain free from defects in design, material and workmanship under normal use and service and will conform in all material respects to the applicable specifications set forth in purchase order or agreement; ZTE does not warrant that operation of the Equipment will be error-free or uninterrupted.
ZXDSL 831AⅡ User’s Manual other cause beyond the range of normal usage for equipments. End User shall assure that Equipment is installed and maintained by ZTE or ZTE-certified individuals in accordance with ZTE’s certification procedures; provided that if End User causes or permits services to be provided by individuals who are not ZTE-certified, the Warranty shall be void as to all Equipment serviced in breach of this sentence.
ZXDSL 831AⅡ User’s Manual WITH USING OF THIS PRODUCT, WHETHER OR NOT ZTE HAD BEEN ADVISED, KNEW OR SHOULD HAVE KNOWN OF THE POSSIBILITY OF SUCH DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, COST OF CAPITAL, COST OF SUBSTITUTE FACILITIES OR EQUIPMENT, ANY DOWNTIME COSTS OR CLAIMS OF END USERS.
Contents Chapter 1 Safety Guidance............................................................1 1.1 Safety Check......................................................................................... 1 1.2 Safety Cautions..................................................................................... 1 Chapter 2 Overview .......................................................................3 2.1 Features...............................................................................................
Chapter 1 Safety Guidance 1.1 Safety Check Before installing the ZXDSL 831AⅡ ADSL equipment, you must check the following items. 1 Electric safety z Ensure that there are no inflammable, conductive or moist objects around. Check whether the cables are aged and whether other electrical appliances are placed stably. 2 Equipment position z Because the running electric devices easily generate heat, please ensure that these devices are positioned in a well ventilated environment.
ZXDSL 831AⅡ User’s Manual z Use the power adapter accompanied in the package. z Rather than directly connecting phones to the ADSL line, led them out from the phone interface of the splitter. z Never place any objects on the equipment. z Keep the equipment dry, ventilated and rainproof, and clean. z Unplug the power and all connection cables in case of thunderstorms, to protect the equipment against lightning. z Clean the equipment using a soft and dry cloth rather than liquid or atomizers.
Chapter 2 Overview The ZXDSL 831AⅡ is an ADSL access device that allows multiple line transmission modes. The equipment provides a 10/100Base-T Ethernet interface and a USB port in a local LAN device. Through the high-speed ADSL access service, the ZXDSL 831AⅡ can provide the broadband Internet service or enterprise network access service for users. 2.
ZXDSL 831AⅡ User’s Manual 2.2 Product Specifications z Environmental requirements Environmental temperature: 0°C-40°C (32 °F-104°F) Humidity: 20% - 90% (non-condensing) z Power specification Power adapter: Input: AC 100-240V ±10%, 50 Hz Output: DC 12V, 500mA z Certification CE Note: In some countries or regions, a DC power adapter may be used instead of an AC power adapter in accordance with customers' request. 2.
ZXDSL 831AⅡ User’s Manual z Quality Warranty Card ×1 z Certificate of Quality ×1 z CD ×1 Note: for your information only, please refer to the actual product. Note: Please use a power adapter that matches the ZXDSL 831AⅡ package. 2.4 System Requirement Before installing the ZXDSL 831AⅡ, please check the following items.
Chapter 3 Installation Preparation 3.1 Hardware Description Front panel Figure 3.1-1 Front Panel of the ZXDSL 831AⅡ Table 3.1-1 Descriptions of the LEDs on the Front Panel LED No.
ZXDSL 831AⅡ User’s Manual LED No. Color Ethernet Green Status On Off Flash On Note The USB interface is in the communication status The Ethernet interface is in the non-communication status Data is received or sent on the Ethernet interface The Ethernet interface is in the communication status Rear panel Figure 3.1-2 Rear Panel of the ZXDSL 831AⅡ Table 3.
ZXDSL 831AⅡ User’s Manual Connection 1 The following connection method is recommended. Figure 3.2-1 shows the connection between a ZXDSL 831AⅡ, computer, splitter and telephones. Figure 3.2-1 ZXDSL 831AⅡ Connection Schematic Diagram (No Phone sets are Installed Before the Splitter) Connection 2 Figure 3.2-2 shows the connection when the splitter is installed near the ZXDSL 831AⅡ.
ZXDSL 831AⅡ User’s Manual Figure 3.2-2 ZXDSL 831AⅡ Connection Schematic Diagram (Phone sets are Installed Before the Splitter) Note: In the circumstance where the first connection example is not applicable and you choose to use the second example, you must install a MicroFilter on the telephone cable (as illustrated in Figure 3.3-2, do not use a splitter to replace the MicroFilter).
ZXDSL 831AⅡ User’s Manual terminal to the Ethernet adapter of the customer computers or ports of other network devices. 3 Connect the plug of the USB cable into the USB port of the ZXDSL 831AⅡ, connect the other end of the USB cable to the USB port of the PC. 4 Connect the splitter The splitter has three interfaces, which are described as follows: z LINE: Connect the user telephone cable (RJ11 interface). z MODEM (or ADSL): Connect the DSL interface of the ZXDSL 831AⅡ.
ZXDSL 831AⅡ User’s Manual The telephone cable is correctly connected if the received telephone signals are normal and free of noise. And the telephone will not be affected no matter whether the ZXDSL 831AⅡ is powered on or off.
Chapter 4 Install USB Driver If you want the ZXDSL 831AⅡ to be connected with a PC through the USB interface, you need to install the USB driver first. Read a certain section below pertinent to your operating system. If you have already installed the driver, skip this chapter. ZXDSL 831AⅡ is a device with both Ethernet Interface and USB Interface, which is independent, you may use either of them to connect to the different computers, in this way the two computers can connect to the network at one time.
ZXDSL 831AⅡ User’s Manual For Windows XP The steps are as follows: 1 Connect USB port of the ZXDSL 831AⅡ to USB port on your PC with the USB cable that comes with the ZXDSL 831AⅡ. 2 plug in the power cord, and turn on the power. 3 Once the new hardware is detected as shown in the dialog box below, Choose "No, not this time". As shown in Figure 4.1-1, Click "Next" button. Figure 4.1-1 4 The dialog box is as shown in Figure 4.
ZXDSL 831AⅡ User’s Manual Figure 4.1-2 5 The dialog box is as shown in Figure 4.1-3. Choose "Search for the best driver in these locations", and Click "Next" button.
ZXDSL 831AⅡ User’s Manual Figure 4.1-3 6 A new box will pop up for selection of the location of the driver. If the location is incorrect please click "Browse" and select the right location, then click "Next" button. As shown in Figure 4.1-4. Figure 4.1-4 7 Click "Continue Anyway" for any dialog box pops up.
ZXDSL 831AⅡ User’s Manual Figure 4.1-5 8 A message box will show the installation of "ZTE USB Remote NDIS Device" is complete. Click "Finish" button. As shown in Figure 4.1-6. Figure 4.1-6 9 After the steps above, you will find there is a new item called "ZTE USB Remote NDIS Device" in "Control Panel"-"System"-"Hardware"-"Device Manager"-"Network adapters". As shown in Figure 4.1-7.
ZXDSL 831AⅡ User’s Manual Area Connection X" is added in "Network Connections". As shown in Figure 4.1-8. Figure 4.1-7 Figure 4.1-8 Note: If the USB device cannot be detected by the system, check the USB cable between the PC and the device, and make sure that the device is powered on.
ZXDSL 831AⅡ User’s Manual 4.2 USB Driver Uninstall For Windows XP 1 Right click the icon of "My Computer" on the desktop, choose "Properties" item on menu pop up. As shown in Figure 4.2-1. Figure 4.2-1 2 Click "Device Manager" button in "Hardware" page. Figure 4.2-2.
ZXDSL 831AⅡ User’s Manual Figure 4.2-2 3 Double Click the "ZTE USB Remote NDIS Device" in "Device Manager" dialog box. As shown in Figure 4.2-3 Figure 4.
ZXDSL 831AⅡ User’s Manual 4 Click "Uninstall" button in "Driver" page. As shown in Figure 4.2-4. Figure 4.2-4 5 Click "OK" when the dialog box shown as below to finish the uninstall. Figure 4.
Appendix A FAQs 1 All indicators are off after the ZXDSL 831AⅡ equipment is powered on First make sure that you have inserted the power adapter of the ZXDSL 831AⅡ into a working power socket and that the ZXDSL 831AⅡ has been powered on (the switch button is pressed down). If the indicators are still off after confirmation of the above items, the hardware is damaged probably. You may contact local operators for maintenance. Never dismantle the equipment by yourself.
ZXDSL 831AⅡ User’s Manual 5 Password verification failure MODEM synchronization and connection are normal. However, sometimes the password fails to be verified. 1. Note that the account and password are case sensitive and some accounts contain a domain name. 2. Virtual dialup software. It is possible that sometimes the virtual dialup software is faulty, or conflict with other software in the operating system.
ZXDSL 831AⅡ User’s Manual 7 The authenticated user names and passwords cannot be re-authenticated? This problem may be due to the following reasons: 1. Your account has expired or you are a defaulting subscriber (please pay the deficit sum). 2. You move into a new area. Because the account and the path PVC are bundled by some operators, your previous account and password cannot be authenticated after you changed your path. 3. One of your accounts has logged on successfully.
Appendix B Standard Compliance The equipment complies with the following ADSL standards: Standard ANSI T1.413 Issue 2 Note ITU G.992.1 Annex A ITU G.992.2 Annex A ITU G.992.3 Annex A ITU G.992.3 Annex L ITU G.992.5 Annex A ITU G.994.1 Only supported by the ZXDSL 831AⅡ Only supported by the ZXDSL 831AⅡ Only supported by the ZXDSL 831AⅡ ZTE’s equipment complies with the following national standards of the PRC: Standard No.
Customer Information 1. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On bottom of this equipment is a label that contains, among other information, a product identifier of ZTEDL05BZXDSL831 . If requested, this number must be provided to the telephone company. 2. If this equipment ADSL CPE causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required.