ZXHN F660 GPON ONT User Manual Manual No: SJ-20140718085850-002 Edition Time: 2017-06-22 (R1.0) LEGAL INFORMATION Copyright © 2017 ZTE CORPORATION. The contents of this document are protected by copyright laws and international treaties. Any reproduction or distribution of this document or any portion of this document, in any form by any means, without the prior written consent of ZTE CORPORATION is prohibited.
1 Safety Precautions Usage Cautions � Read all the safety cautions carefully before using the device. � Only use the accessories included in the package, such as power supply adapter. � Do not extend the power cord, otherwise the device will not work. � The power supply voltage must meet the requirements of the device input voltage (The voltage fluctuation range is less than 10%). � Keep the power plug clean and dry to prevent any risk of electric shock or other dangers.
2 Package Content Please make sure the ZXHN F660 package contains the following items. Item Quantity ZXHN F660 unit One AC-DC power supply adapter One RJ-45 Ethernet cable One User manual One Note: A socket outlet that is installed near equipment and that shall be easily accessible. If any of the items included in the package is incorrect, lost or damaged, please contact your service provider. If you need to replace the product, please keep the package and all the items in good condition.
Figure 3-1 Table 3-1 describes the indicators on the front panel of the ZXHN F660 unit. Table 3-1 Indicator Status Description Off No power Power PON LOS Solid green Power on Off The ONT registration fails or the system is not powered on. Solid green The ONT registration is successful. Flashing green The ONT is being registered. Off The ONT received optical power is normal. Solid red Flashing red The optical transmitter of the PON interface is powered off.
Indicator Status Off Internet Solid red Flashing red Off Solid green Wi-Fi Flashing green Off Phone1 – Phone2 Solid green Flashing green Off LAN1 – LAN4 WPS Solid green The data is being transmitted or received. The device is not powered on or it cannot be registered to the soft switch. The device has been registered to the soft switch, but there are no POTS services. The POTS communication service is being provided. The device is not powered on or the network link is not established.
Figure 4-1 Table 4-1 describes the interfaces and buttons on the back panel of the ZXHN F660 unit. Table 4-1 Interface/Button Description On/Off Power switch. Power 12 V DC power connector. USB USB 2.0 interface. Reset Reset button, when the power is on, use a needle to press the button for over 5 seconds to restore the default settings. Wi-Fi Enable/disable the Wi-Fi function. WPS Enable/disable the Wi-Fi protection.
5 Product Features Interfaces � GPON � � � � interface: GPON standard, SC/APC, comply with ITU G.984.1–G.984.5 standards. Ethernet interface: Four GE interfaces, RJ-45, comply with IEEE 802.3 and IEEE 802.3u standards. Phone interface: RJ-11. Wi-Fi interface: Comply with IEEE 802.11n standard. USB Interface: Standard USB 2.0 interface. Technical Features � Broadband service access: Connected to Internet through the GPON access method.
Frequency bands Maximum Output Power 802.11b 15 ~ 19 dBm 802.11g 14 ~ 18dBm 802.11n(HT20) 14 ~ 18dBm 802.11n(HT40) 14 ~ 18dBm 7 Cable Connection shows the devices that are connected to the ZXHN F660 device. After the devices are connected to the ZXHN F660 device, press the power button. When the corresponding indicators on the front panel are On, you can enjoy various services provided by the service provider.
The power adapter is not correctly connected to the device. Be sure to use the power adapter supplied with the device. The LOS indicator is flashing red or solid red after the device is powered on. � The optical fiber is not correctly connected to the ONT PON interface. � The optical fiber is broken or damaged. � If the indicator is solid red or keeps flashing, please contact the service provider for maintenance. The PON indicator on the front panel is off or flashing green after the device is powered on.
users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.