ZXHN F680 GPON ONT User Manual Manual No: SJ-20170410154357-004 Edition Time: 2019-04-15(R1.0) LEGAL INFORMATION Copyright © 2018 ZTE CORPORATION. The contents of this document are protected by copyright laws and international treaties. Any reproduction or distribution of this document or any portion of this document, in any form by any means, without the prior written consent of ZTE CORPORATION is prohibited.
1 Safety Precautions Note: Before using the device, read the following safety precautions. ZTE bears no liability to the consequences incurred by violation of the safety instructions. Usage Cautions � Read all the safety cautions carefully before using the device. � Only use the accessories included in the package, such as power supply adapter. � Do not extend the power cord, otherwise the device will not work.
you reuse or recycle your end-of-life equipment by using an accredited electronics take-back system. The symbols below indicate that this product should be reused or recycled and not simply discarded. Please locate and use an appropriate reuse and recycling site. If you need more information on collection, reuse and recycling systems, contact your local or regional waste administration. You may also contact your equipment provider for more information on the environmental performances of these products.
Figure 3-1 Indicators of the ZXHN F680 Unit Table 3-1 describes the indicators on the front panel of the ZXHN F680 unit. Table 3-1 Indicators on the Front Panel Indicator Status Description Off The device is powered off. Solid green The device is powered on. Off The ONT registration fails or the system is not powered on. Solid green The ONT registration is successful. Flashing green The ONT is being registered.
Indicator Status Off The ONT received optical power is normal. Solid red The optical transmitter of the PON interface is powered off. Flashing red The received optical power is less than the optical receiver sensitivity, or the device is downloading a program package. LOS Internet USB LAN1– LAN4 Phone1 Phone2 Description Off The device is not powered on, there is no WAN connection with Internet properties configured, or the WAN configuration is not effective.
Indicator 2.4GHz 5GHz WPS BBU 4 Status Description Off The device is not powered on or the wireless interface is disabled. Solid green The wireless interface is enabled. Flashing green Data is being transmitted. Off The device is not powered on or the wireless interface is disabled. Solid green The wireless interface is enabled. Flashing green Data is being transmitted. Yellow Negotiation is in progress. Green Negotiation is successful.
Figure 4-1 Interfaces and Buttons on the Back Panel Table 4-1describes the interfaces and buttons of the ZXHN F680 unit. Table 4-1 Descriptions of the Interfaces and Buttons on the Back Panel Interface/Button Description Phone1/Phone2 BBU RJ-11 telephone interface, connected to the telephone with RJ-11 telephone cable. Standby power supply interface, connected to a standby power supply through a dedicated cable. LAN1– LAN4 RJ-45 Ethernet interface. USB1 Standard USB 3.
Interface/Button Description On/Off Power switch. Power 12 V DC power connector. PON PON interface. USB2 Reset WPS Wi-Fi • Standard USB 2.0 interface, connected to a USB storage device for file sharing, fast backup, and data restoration. Reset key used when the device is powered on and activated. � By using a thin needle, press the key inside the hole and then immediately release the key, and then the device is restarted. The configurations will not be lost.
� Security: Provides multi-level authentication based on the device, user and service, and provides the data channel encryption for safety. � QoS: Provides QoS services meeting the requirements of various services for the local devices and network � Network management: Provides multi-mode network management. 6 Pechnical Specification For the product specifications of the ZXHN F680 , refer to Table 6-1.
Figure 7-1 Entire Connection Verify that the cable connections are correct, and press the On/Off button. After the power indicator is lit and other indicators operate properly, services of the carrier can be used. 8 Troubleshooting The Power indicator on the front panel is off after the power button is pressed. The power adapter is not correctly connected to the device. Be sure to use the power adapter supplied with the device.
The Phone indicator on the front panel is off after the device is powered on. The telephone function is abnormal. Please contact the service provider for help. 9 FCC Statement FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.