ZXR10 WAS (V2.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Manual Version Product Version BOM 20040306-R1.0 V2.0 ×××××××× Copyright © 2003 ZTE Corporation All rights reserved. No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any means without the prior written permission of ZTE Corporation.
FAX: +86-755-26770160 Suggestions and Feedback To improve the quality of ZTE product documentation and offer better services to our customers, we hope you can give us your suggestions and comments on our documentation and fax this form to 0086-755-26770160; or mail to “ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China”. Our postcode is 518057. Document Name ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point User’s Manual Product version V2.
Preface About This Manual This manual, ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point — User’s Manual, is applicable to W800A wireless access point (W800A for short) of the ZXR10 WAS (V2.0) IP wireless access system. The ZXR10 WAS IP wireless access system is the IP wireless access system developed by ZTE. It consists of a series of wireless access network products, such as wireless network card, wireless access point (AP) and DSL 2-in-1 wireless router.
Statement: The actual product may differ from what is described in this manual due to frequent update of ZTE products and fast development of technologies. Please contact the local ZTE office for the latest updating information of the product.
Contents 1 Safety Precautions ...................................................................................................................1-1 1.1 Safety Precautions .............................................................................................................1-1 1.2 Symbol Description ...........................................................................................................1-2 2 Installation and Debugging.................................................................
3.3.6 Exiting the Privileged Mode ....................................................................................... 3-6 3.3.7 Exiting the Telnet Configuration ................................................................................. 3-6 3.4 Configure Mode................................................................................................................ 3-6 3.4.1 Bridge Configuration .................................................................................................
3.4.24 TELNET Configuration .......................................................................................... 3-32 3.4.25 Uploading/Downloading TFTP Files ........................................................................ 3-32 3.4.26 VLAN Configuration.............................................................................................. 3-33 3.4.27 Web Configuration ................................................................................................. 3-34 3.4.
A List of Figures Fig. 2.1-1 Sub-Channel Distribution........................................................................................2-1 Fig. 2.1-2 Channel Distribution Principle of Adjacent APs .........................................................2-2 Fig. 2.2-1 installation instruction ............................................................................................2-5 Fig. 2.2-2 Soldered Connectors......................................................................................
A list of Tables Table 1.2-1 Safety Symbols and Descriptions ...........................................................................1-3 Table 2.1-1 IDs and Frequencies of Channels ...........................................................................2-2 Table 3.6-1 W800A Working Channels .................................................................................. 3-45 Table A.1-1 Connections of Straight Through Ethernet Cables (RJ45) ............................................1 Table A.
1 Safety Precautions This chapter introduces the safety precautions of this product and safety symbols used in this manual. 1.1 Safety Precautions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ( 1) This device may not cause harmful interference, and( 2) this device must accept any interference received, including interference that may cause undesired operation.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual personnel who had passed the training can install, operate and maintain it. ZTE assumes no responsibility for consequences resulting from violation of general specifications for safety operations or of safety rules for design, production and use of equipment. 1.2 Symbol Description See Table 1.
Chapter 1 Safety Precautions Table 1.2-1 Safety Symbols and Descriptions Safety Symbols Meaning Call for notice Call for antistatic measures Warn against electric shock Caution against scald Warn against laser Caution against microwave Four types of safety levels are available: danger, warning, caution and note. To the right of a safety symbol is the text description of its safety level. Under the symbol is the detailed description about its contents. See the following formats.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Note: Any failure to take the reminder seriously may lead to injury accidents or damage to the equipment. & Remark, reminder, tip… The remarks, prompt and tips in addition to safety statements.
2 Installation and Debugging This chapter details the methods and procedure of installation and debugging of the W800A for your reference. 2.1 Installation Preparations 2.1.1 Installation Preparation Flow Before installing the W800A, the engineering personnel should confirm that such work as solution design, project survey and W800A basic configurations have been completed. Brief introductions to the preparations required for installation are as follows. 2.1.1.1 Channel Planning According to 802.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Table 2.
Chapter 4 Installation and Debugging When using APs, for the adjacent APs, we will select their working channels (channels 1, 6 and 11 are usually used) according to the principle shown in Fig. 2.1-1, to guarantee the normal work of the wireless LAN. The channel distribution principle of 802.11g standard is the same as that of 802.11b. 802.11a standard channels feature anti-interference performance, so no special configuration is required.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 2.1.3 Installation Environment Inspection The W800A can only be used indoors. To guarantee the normal work and longer useful life of the equipment, the indoor temperature range should be -5 °C ~ 45 °C, you should maintain good ventilation and dry air indoors, and the relative humidity range is 5% ~ 95%. 2.1.
Chapter 4 Installation and Debugging Fig. 2.22-1 installation instruction When the W800A is installed on the ceiling, for the ceiling in plaster or floor, the W800A antenna can be directly installed on the ceiling; for the ceiling in metal, if the antenna is directly installed on the ceiling, the antenna signal will be shielded and W800A can not work normally, so you should lead the antenna to the place under the ceiling, through correct antenna feeder.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Fig. 2.22-2 Soldered Connectors b) Gluing together by using permanent, fast-setting epoxy glue and surround the entire periphery of the connector junction so it is not possible to disconnect. Follow the directions provided on the glue package for cleaning and mixing the two-part glue together. 2.3 Power-on and Power-off The following two power methods are used for the W800A system. 1.
Chapter 4 Installation and Debugging 1. Ensure that the route between W800A and Internet/customer server is smooth. 2. Ensure that each client in the W800A coverage area can access Internet normally. 3. Ensure that in the whole engineering coverage area, the clients can be roaming switched between the cells containing APs.
3 Command Line Configuration This chapter describes the operation methods and configuration commands of the W800A command line configuration. 3.1 Overview The W800A provides the Command Line Interface (CLI) for configuring the W800A data. The CLI configuration of the W800A has the following features: 1.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 7. CLI provides two layers of password protection to reject illegal users. The first layer password authentication appears on the Telnet welcome interface, the safety authentication for accessing the user mode is required at this time. The default user name is “root” and default password is “public”.
Chapter 5 Command Line Configuration Fig. 3.-1 Serial Port Configuration When the Telnet mode is used for configuring the W800A, you just need input “telnet/W800A working IP address”, as shown in Fig. 3.1-2. By default, the W800A working IP address is 192.168.1.254 and the subnet mask is 55.255.255.0. Fig. 3.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual follows: 1. abc refers to the command or keyword. 2. refers to the contents to be input by the user. 3. abc|def indicates that one of the two will be selected. 4. For the contents included in [ ], the user can choose to input or not input them.. 5. For the contents included in { }, the user must input them. 3.
Chapter 5 Command Line Configuration 3.3 Privileged Mode Entering mode: Input the enable command in the user mode and input correct password. Exiting mode: disable, entering the user mode; exit, exiting the privileged mode and returning to the system. Default prompt character: wlan # 3.3.1 Network Connectivity Check Command mode: Privileged mode Function: Checking the network connectivity. Command format: ping
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual and reset it. Command format: default enable 3.3.4 Resetting the Software Command mode: Privileged mode Function: Resetting the W800A. Command format: reboot 3.3.5 Entering the Configure Mode Command mode: Privileged mode Function: Entering the configure mode. Command format: configure terminal 3.3.
Chapter 5 Command Line Configuration 3.4.1 Bridge Configuration 1. bridge aging-time Command mode: Configure mode Function: Configuring the aging time of the Bridge Forward Table (FDB) MAC address. Command format: bridge aging-time Parameter descriptions: Parameter Name 2. Value Range Parameter Descriptions The aging time of the FDB MAC address (unit: 10~1000000 second), 300 by default.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3.4.3 Configuring the Configuration Server Command mode: Configure mode Function: Configuring the parameters of configuration server: IP address, interception port number of the TCP and the interception port number of UDP. Command format: config-server {ipaddress [tcp-port [udp-port ] | udp-port [tcp-port ]] | tcp-port [ipaddress
Chapter 5 Command Line Configuration Command mode: Configure mode Function: Configuring the IP address parameters of the default gateway of the DHCP server. Command format: dhcp server gateway Parameter descriptions: Parameter Name 3. Value Range IP address Parameter Descriptions IP address of the gateway. dhcp server leasetime Command mode: Configure mode Function: Configuring the address lease time of the DHCP server.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name Value Range Parameter Descriptions The start flag of the DHCP server. If it is “true”, the DHCP server will be started when {true|false} True, false the system is restarted. If it is “false”, the DHCP server will not be started when the system is restarted. 3.4.5 DISCOVER Configuration 1.
Chapter 5 Command Line Configuration Parameter Name Value Range Parameter Descriptions IP address with a The management multicast address of the range of 224.0.0.1 ~ integrated management server, 224.1.88.88 by 239.255.255.254. default. The management interception port number of the 0~65535 integrated management server, 2800 by default. 3.4.6 802.1X Parameter Configuration 1. dot1x enable Command mode: Configure mode Function: Enabling or disabling the 802.1x function.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Command mode: Configure mode Function: Configuring the domain name in the EAP-MD5 authentication mode. Command format: dot1x md5-domain Parameter descriptions: Parameter Name 5. Value Range 1 ~ 32 characters Parameter Descriptions The domain name in the EAP-MD5 authentication mode, USR by default. dot1x nas-id Command mode: Configure mode Function: Configuring the 802.
Chapter 5 Command Line Configuration Command mode: Configure mode Function: Configuring the time-out time of the 802.1x authentication server. Command format: dot1x server-timeout Parameter descriptions: Parameter Name 9. Value Range Parameter Descriptions The authentication server time-out time (unit: 1~255 second), 60 by default. dot1x sim-domain Command mode: Configure mode Function: Configuring the domain name in the EAP-SIM authentication mode.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter Name Value Range Parameter Descriptions The 802.1x sending period (unit: second), 3 by 1~255 default. 12. dot1x wpa-domain Command mode: Configure mode Function: Configuring the domain name in the WPA authentication mode.
Chapter 5 Command Line Configuration Function: Exiting the configure mode and entering the privileged mode. Command format: exit 3.4.10 IAPP Load Balance Configuration 1. iapp balance Command mode: Configure mode Function: Configuring the load balance mode and nominal capacity of the load balance group. Command format: iapp balance {flow |user } Parameter descriptions: Parameter Name 1 Value Range 1~65535 1~65535 1~30 2.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3. iapp max-user Command mode: Configure mode Function: Configuring the maximum user quantity (the quantity of the users can be accessed). Command format: iapp max-user Parameter descriptions: Parameter Name Value Range Parameter Descriptions The maximum quantity of the wireless users can be 1~150 accessed by the system, 30 by default. 3.4.
Chapter 5 Command Line Configuration has two wireless interfaces, so this value is 0 or 1. 3.4.12 IP Network Parameter Configuration 1. ip address Command mode: Configure mode Function: Adding the IP address of the W800A management interface. Command format: [no] ip address [second] Parameter descriptions: Parameter Name Value Range Parameter Descriptions 1 IP address IP address of the host. 2 Subnet mask Subnet mask of the host.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual IP address Initial IP address of the host address pool. 2 IP address End IP address of the host address pool. 3 Subnet mask Subnet mask of the address pool address. 3.4.13 Kicking Users 1. kick all Command mode: Configure mode Function: Kicking all the users. Command format: kick all 2.
Chapter 5 Command Line Configuration 3. l2-separate mode Command mode: Configure mode Function: Configuring the two-layer separation working mode. Command format: l2-separate mode {simple_mode | gateway_mode } Parameter descriptions: Parameter Name Value Range Parameter Descriptions {simple_mode| simple_mode, Selecting the simple mode or gateway mode for the gateway_mode } gateway_mode two-layer separation. 3.4.15 Log Printing Message Configuration 1.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter Name Value Range Specified Parameter Descriptions module names: BSP, DATABASE, 80211, BRIDGE, IAPP, DHCP, IPPOOL, DOT1X, RADIUS, ACL, The module containing the log printing messages. SVCMANAGE, TELNET, WEB, CONSOLE, SNMP, ALARM, R01, TFTP, DISCOVER, QOS 4.
Chapter 5 Command Line Configuration Parameter Name Value Range Parameter Descriptions The MAC address sending the MAC packet. Two methods can be used for specifying the source address: { |any} any address or One is to use the format of 48-bit 6 hexadecimal hyphens, for example: 00-d0-d0-f1-c4-ef. The other is to use the keyword any as the abbreviation of the source 00-00-00-00-00-00. This keyword is not recommended. 3.4.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name Value Range Parameter Descriptions 1 1 ~ 32 characters User name 2 1 ~ 32 characters User password. 3.4.19 QoS Configuration 1. qos enable Command mode: Configure mode Function: Enabling or disabling QoS function. Command format: [no] qos enable 2. qos policy Command mode: Configure mode Function: Configuring QoS policy.
Chapter 5 Command Line Configuration Parameter Name 2 2. Value Range 1 ~ 255 characters Parameter Descriptions Character string of the accounting shared secret key radius-server authen Command mode: Configure mode Function: Adding or deleting the authentication server of an ISP. Command format: [no] radius-server authen {master|slave }
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 5. radius-server retry-times Command mode: Configure mode Function: Configuring the retrying times of the RADIUS authentication of an ISP. Command format: radius-server retry-times Parameter descriptions: Parameter Name Value Range 1 ~ 32 characters 1~10 6. Parameter Descriptions ISP name, and only the created ISP can be input.
Chapter 5 Command Line Configuration 2. snmp access-mode Command mode: Configure mode Function: Configuring the local agent can be accessed by all the hosts or the host in access-host. Command format: snmp access-mode {all|list} Parameter descriptions: Parameter Name {all|list} 3. Value Range Parameter Descriptions all: All the users can access it. All, list list: The users in access-host can access it.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name Value Range Any character. Parameter Descriptions Serving as the end mark of inputting character string. A management variable content in the MIB II 1 ~ 255 characters system group, containing the name and contact method of the equipment manager. 6.
Chapter 5 Command Line Configuration Parameter Name 9. Value Range 0~241920000 Parameter Descriptions A management variable in the MIB system group, describing the NE code of the managed equipment. snmp nodecreatdate Command mode: Configure mode Function: Configuring the creation time information of the NE of the managed equipment.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter Name Value Range Any character. Parameter Descriptions Serving as the end mark of inputting character string. RFC1213, a management variable in the MIB 1 ~ 255 characters system group, and it is the name of the managed equipment. 12. snmp trap enable Command mode: Configure mode Function: Enabling or disabling SNMP Agent to send trap.
Chapter 5 Command Line Configuration Command mode: Configure mode Function: Generating SSH server secret key. Command format: ssh server generate-key rsa 4. ssh server auth isp-name Command mode: Configure mode Function: Configuring SSH with the ISP name of the authentication server authenticated by radius. Command format: ssh server auth isp-name Parameter descriptions: Parameter Name 5.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Command mode: Configure mode Function: Configuring the forwarding delay time of the spanning tree protocol bridge. Command format: stp bridge forward-delay Parameter descriptions: Parameter Name 2. Value Range Parameter Descriptions The forwarding delay time of the spanning tree 4~30 protocol bridge (unit: second), 15 by default.
Chapter 5 Command Line Configuration Parameter Name 5. Value Range Parameter Descriptions The priority of the spanning tree protocol bridge, 0~65535 32768 by default. stp enable Command mode: Configure mode Function: Enabling or disabling the spanning tree protocol function. Command format: [no] stp enable 6. stp interface path-cost Command mode: Configure mode Function: Configuring the path cost of the spanning tree protocol interface.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name Value Range {eth0|wlan0|wlan1} eth0, wlan0, wlan1 {enable|disable} Enable, disable Parameter Descriptions Configured interface. The state of the spanning tree protocol interface, enable by default. 3.4.24 TELNET Configuration 1. telnet enable Command mode: Configure mode Function: Enabling or disabling Telnet function.
Chapter 5 Command Line Configuration Command format: tftp get {runbin | zxipcmd.dat | database.dat} Parameter descriptions: Parameter Name Value Range Parameter Descriptions The TFTP server IP address represented by dotted IP address {runbin| Runbin, The full file name (including the extension name) zxipcmd.dat| zxipcmd.dat, of the version file set to be transmitted on the TFTP database.dat} database.dat server. 3. decimal.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Command mode: Configure mode Function: Enabling or disabling VLAN function. Command format: [no] vlan enable 2. vlan manager-vlanid Command mode: Configure mode Function: Configuring the VLAN of the management interface. Command format: vlan manage r-vlanid Parameter descriptions: Parameter Name Value Range Parameter Descriptions 0: The management interface is without VLAN.
Chapter 5 Command Line Configuration Parameter descriptions: Parameter Name Value Range NA: Not been configured; NA CA: Canada; CA CN: China; CN TW: Taiwan; TW {NA|CA|CN|TW| FR FR|GE|HK|KR| GE MX|GB|US } HK Parameter Descriptions FR: France; GE: Germany; HK: Hongkong; KR: Korea; KR MX: Mexico; MX GB: Britain; GB US: USA; US The default value is CN. 3.4.29 Showing Parameter Configuration 1.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name 2. Value Range 1~3 Parameter Descriptions Alarm levels. show bridge Command mode: Configure mode Function: Showing the bridge configuration parameter information. Command format: show bridge 3. show config-server Command mode: Configure mode Function: Showing the parameter information of the configuration server.
Chapter 5 Command Line Configuration Command format: show iapp 8. show interface Command mode: Configure mode Function: Showing the parameter information of the interface configuration. Command format: show interface {ethernet|wlan} {0|1} 9. show ip 1) show ip address Command mode: Configure mode Function: Showing IP address information. Command format: show ip address 2) show ip pool = show ip pool config Command mode: Configure mode Function: Showing all the IP address pool information.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 10. show l2-separate Command mode: Configure mode Function: Showing the parameter information of the 2-layer separation configuration. Command format: show l2-separate 11. show logmsg Command mode: Configure mode Function: Showing all the configuration information and configuration historical commands of log printing. Command format: show logmsg {config|logcmd} 12.
Chapter 5 Command Line Configuration Command mode: Configure mode Function: Showing the parameter information of manage-user configuration. Command format: show manage -user 16. show multi-essid Command mode: Configure mode Function: Showing the parameter information of multi-essid configuration. Command format: show multi-essid Parameter descriptions: Parameter Name Value Range Parameter Descriptions 0 or 1 Number of the wireless interface. 17.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual configuration. Command format: show snmp community 3) show snmp nodeinfo Command mode: Configure mode Function: Showing the parameter information of snmp nodeinfo configuration. Command format: show snmp nodeinfo 4) show snmp sysinfo Command mode: Configure mode Function: Showing the parameter information of snmp sysInfo configuration.
Chapter 5 Command Line Configuration Command format: show stp bridge 2) show stp interface Command mode: Configure mode Function: Showing the parameter information of stp interface configuration. Command format: show stp interface 23. show telnet-idletime Command mode: Configure mode Function: Showing the parameter information of the automatic exiting time when the Telnet window is idle. Command format: show telnet-idletime 24.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Note: All the information of the corresponding interface can be configured in this mode. 3.5.1 Exiting the Ethernet Interface Configuration Mode Command mode: Ethernet interface configure mode Function: Exiting the Ethernet interface configuration mode and entering the configure mode. Command format: exit 3.5.
Chapter 5 Command Line Configuration Parameter descriptions: Parameter Name Value Range Parameter Descriptions {OpenSystem| OpenSystem, The wireless authentication mode is configured as ShareKey} ShareKey open system or shared secret key mode. 2. 80211 essid Command mode: Wireless interface configure mode Function: Configuring the wireless network ESSID. Command format: 80211 essid Parameter descriptions: Parameter Name 3.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Function: Configuring the wireless standard working mode of the wireless interface. Command format: 80211 wirelessmode {11a|11b|11g|help} [channel ] [rate ] Parameter descriptions: Parameter Name Value Range Parameter Descriptions 11a: Configuring 800A as the 802.11a working mode. 11b: Configuring 800A as the 802.11b working mode.
Chapter 5 Command Line Configuration Table 3.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3.6.3 Exiting the Wireless Interface Configuration Mode Command mode: Wireless interface configure mode Function: Exiting the wireless interface configuration mode and entering the configure mode. Command format: exit 3.6.4 Enabling the Link Integrity Detection Function Command mode: Wireless interface configure mode Function: Enabling or disabling the AP link integrity detection function.
Chapter 5 Command Line Configuration [priority ] Parameter descriptions: Parameter Name Value Range Parameter Descriptions 1 ~ 32 characters ESSID name. 1~4094 The VLAN ID corresponding to the ESSID. 1~30 1 3 The maximum user quantity corresponding to the ESSID. 0~7 The priority corresponding to the ESSID. 3.6.7 Security Parameter Configuration 1.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name Value Range Parameter Descriptions {key1|key2| key1, key2, The article number of the secret key to be key3|key4} key3, key4 configured.
Chapter 5 Command Line Configuration Parameter descriptions: Parameter Name 5. Value Range 8 ~ 36 characters Parameter Descriptions Configuring the shared secret key of the WPA encryption. security wpa rekey-interval Command mode: Wireless interface configure mode Function: Configuring the WPA mode to be used.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name {ap|repeater} Value Range ap, repeater Parameter Descriptions The working mode of the equipment.
A.1 Making of Ethernet Cables A.1.1 Making of Straight Through Ethernet Cables (RJ45) In IP wireless access system, the following network cables must adopt the straight through Ethernet cables: 1. The Ethernet cable between the Ethernet switch (end A) and W112P (end B). 2. When no Ethernet switch is used, AP will directly connect with the AC downlink port, at this time, the Ethernet cable between the AC (end A) and AP (end B) must be straight through Ethernet cable. 3.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Table A.
Appendix A Making of Ethernet Cable & Note: The signals and connection methods mentioned here are designed according to the signal definitions of the ZTE AC equipment interface. If the AC in the actual engineering is not from ZTE, modify the cable making methods according to the actual conditions. A.1.4 Ethernet Cable Label After the Ethernet cable is crimped, paste labels on ends A and B of the network cable, indicating name and length of this cable. 1.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual RJ45J **m Fig. A.1-3 Label of the Crossover Ethernet cable In the diagram, “**m” indicates the actual length of the cable; “J” after “RJ45” indicates that this is the crossover Ethernet cable.
