ZXV10 B760E RichMedia Box User Guide ZTE CORPORATION NO.55,Hi-techRoadSouth,ShenZhen,P.R.China Postcode:518057 Tel: (86) 755 26771900 800-9830-9830 Fax: (86) 755 26772236 URL: http://support.zte.com.cn E-mail: doc@zte.com.
LEGAL INFORMATION Copyright © 2012 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. History Revision Revision No. R1.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Content Chapter 1 Safety Instructions...............................................1 Chapter 2 Packing List ......................................................2 Chapter 3 Panels ...............................................................3 3.1 Front Panel .......................................................................................... 3 3.2 Rear Panel ........................................................................................... 3 3.3 Side Panel ................................
Chapter 1 Safety Instructions Special Note • Remove the plastic covering before using the Set-Top Box to provide normal ventilation. • Use the power adapter provided with the Set-Top Box. Important Safety Instructions • Ensure that the electric voltage meets the device requirements. Check the cables periodically, replace any damaged cables immediately. • To prevent electric shock, do not remove cover. There are no user serviceable parts inside. Refer servicing to qualified service.
• The power cable or power socket is damaged. • There is any liquid leaks into the device. • Fails to run normally even after following the instructions. • The device is physically damaged. Chapter Quantity 1 1 2 Packing List Item Remarks Set-Top Box (STB) Remote control 1 Ethernet network cable 1 Power adapter - 1 User Guide - Qualification Certificate/WARRA NTY - 1 1 Packing list - Tips: This packing list is for reference only.
Chapter 3 Panels 3.1 Front Panel 1 Key 2 Name Description Running status indicator Red: STB is in standby state. Green: STB is running normally Not Lit: STB is not powered ON Connection status indicator Blinking (Green): the network connection is normal. Not Lit: the network connection fails or no physical connection. Infrared indicator The green indicator flashes when the STB receives signals from the remote control. 1 2 3 3 3.
Key Name Description 2 SPDIF Optical digital audio output interface. 3 AV Composite video output interface, which can be used for connecting to TV's composite video and audio input interface.. 4 HDMI HDMI output interface. 5 DC+12V Power input socket, +12 V DC power adapter provided. Consult technical personnel before using other types of power adapter. 6 Power switch Make sure the power switch is turned to I after the STB is powered on 3.
WAN interface Telephone line Phone socket Network cable xDSL Modem Video/audio cable TV STB WAN interface LAN Network cable Network cable Network interface Video/audio cable TV STB Video/audio cable AP STB TV 4.2 Video and Audio Connections 4.2.1 Connecting Standard Definition Interface Steps 1. Connect the R and L interfaces on the TV to the corresponding interfaces with AV the cables. 2.
Power adapter —END OF STEPS— 4.2.2 Connecting High Definition Interface Steps 1. Connect the HDMI interface on STB to the corresponding interface on TV with HDMI cable, as shown in the following figure.
TV set Power adapter HDMI Note: HDMI output interface simultaneously generates uncompressed high-definition video and multi-channel audio data. One HDMI data cable is capable of conveying both video and audio data. —END OF STEPS— 4.2.3 Connecting Digital Audio There is one optical digital audio output interface, connect the S/PDIF interface on STB to digital audio amplifier for using digital audio.
4.3 Power ON Steps 1. Ensure that all cables are connected correctly. 2. Install the power cable to STB using the power adapter and to AC power source. 3. Ensure that all other devices are plugged in and receiving power. 4. Turn on the TV. —END OF STEPS— 4.4 Upgrade The STB can connect to the server on each power-on and check whether an upgrade is required. If so, the upgrade starts at once, which normally takes three to five minutes. Do not perform any operations during this period.
Chapter 5 Remote Control 5.
Note: The remote control provided depends on the IPTV service provider. The appearance of remote control shown is for reference only. Notes: • The remote control is powered by two AAA batteries. Insert two AAA batteries into the remote control according to the polarity instruction displayed on it. • During the operation, point the front part of the remote control to the infrared receiving area on the STB. 5.
Note: If the STB remote control fails to control TV after learning, please learn again following the above steps. —END OF STEPS— Chapter 6 Operation Guide 6.1 Standby/Working Status Press key once to switch STB between the standby and working state. Press key once to switch TV between the standby and working state. Use TV/AV key to switch the system mode of TV. 6.2 EPG Operations Press Menu key on the remote control to enter the EPG homepage.
Go to the previous page if there are multiple pages in the same level. Go to the next page if there are multiple pages in the same level. Use the following keys to switch program mode and open the requested page directly. Go to live TV. Go to TV On Demand. Go to Video-On Demand. Go to information surfing program. View program information. 6.3 Common Operations During Watching Programs Use the following keys to control the volume.
Use the following keys to switch channels while watching programs. Press key display the channel number on the screen, then enter channel number to directly turn to. Select the next channel, up and down, when watching TV. 6.4Controlling Program Playing When a program is playing (such as live TV, VOD, TSTV), use the following keys to control the progress of the program. Press program. key to pause the program; Press Press key to stop playing the program.
When playing a single VOD program, press the program. key to go to the end point of Press key to back to the previous chapter. Programs might be organized into chapters. key to go to the start point of the When playing a TSTV program, press program. When playing a single VOD program, press start point.
Press OK key to play the TSTV program from the interested point. Exit TSTV program Press Chapter key to exit TSTV and go back to Live program. 7 Troubleshooting Problem Possible Cause Solution The indicator is not lit after switching on the STB. The power adapter has not been connected. Connect the power adapter. The power adapter is damaged. Consult the service provider and replace power adapter with a new one. The power outlet has no power. Check and ensure the power outlet has power.
Problem Possible Cause Solution been connected properly. No sound from the speaker. The video input source of the TV has been set incorrectly. Switch the system mode of the TV until the EPG page is shown on the TV. The STB is in standby. Turn on STB by pressing key on the remote control. The audio cable has not been connected properly. STB or TV is muted, or the volume has been turned all the way down. The remote control fails. Reconnect audio cable.
Chapter 8 Technical Specification Compliant Standard GB4943.1-2011、GB9254-2008、YD/T993-1998 Power Adapter Input: 100 V ~ 240 V 50Hz/60Hz Output: +12.0 V DC Environment Requirement Working environment temperature: +32 ℉ ( 0 ℃ ) ~ +104 ℉ ( +40 ℃ ) Working environment humidity: 5% ~ 95% Protocol TCP/IP, HTML 4.0, HTTP 1.1/JavaScript 1.5, NTP,FTP, HTTPS/SSL2.0/3.