LEGAL INFORMATION Copyright © 2009 ZTE CORPORATION. The contents of this document are protected by copyright laws and international treaties. Any reproduction or distribution of this document or any portion of this document, in any form by any means, without the prior written consent of ZTE CORPORATION is prohibited. Additionally, the contents of this document are protected by contractual confidentiality obligations.
Contents Safety Instructions ................................................................. i During Installation and Application.......................................................i For Service .......................................................................................ii Chapter 1................................................................................ 1 Introduction........................................................................... 1 Overview..............................
ZXV10 W300 Wireless ADSL Router User Manual Chapter 4 ............................................................................. 10 Network Configuration........................................................ 10 Creating WAN Connection................................................................10 Wireless Configuration.....................................................................14 Configuring WLAN Basic Parameters ............................................................
Safety Instructions During Installation and Application Use the power adapter included in this package. Other power adapters may make the device unable to work normally or even damage the device. Pay attention to the load of the power socket and power cable. The overloading power socket or broken power cable may cause electric shock or fire. It is recommended to check the cables periodically and replace the broken one immediately.
ZXV10 W300 Wireless ADSL Router User Manual For Service Do not attempt to disassemble, repair, or open this product, which will lose the warranty services. Contact qualified service personnel in case of problems, especially under the following conditions: The power socket or cable is damaged. Liquid is splashed into the product. The product is exposed to rain or water. The product does not work normally when the operating instructions are followed.
Chapter 1 Introduction Overview W300 is a home and SOHO oriented wireless broadband router integrating ADSL, AP and LAN Switch. It provides triple-play services such as Internet data, voice access, and video access. W300 provides priority access for different services with sophisticated ATMbased and IP-based QoS to meet different requirements for highspeed Internet access, IPTV Video on Demand (VoD), live-broadcast access and voice access.
ZXV10 W300 Wireless ADSL Router User Manual T ABLE 1 P AC KING LIST Component Quantity ZXV10 W300 Wireless ADSL Router 1 External splitter 1 Power adapter 1 Telephone line 1 Straight-through Ethernet cable 1 Warranty card 1 ZXV10 W300 Wireless ADSL Router User Manual 1 Note: Components actually delivered depend on the service provider. If any component is missing or damaged, contact the service provider immediately. Please keep the packing box and components well in case of replacement.
Chapter 1 - Introduction Indicator Internet DSL Color Green Green LAN1 LAN2 LAN3 Green LAN4 Wi-Fi WPS Green Green Description Steady on: the connection is established and the IP address is allocated. In multi-WAN connection mode, it indicates that the default routing WAN connection is established. Flashing: Data is transmitting. The flashing frequency indicates the LAN traffic.
ZXV10 W300 Wireless ADSL Router User Manual FIGURE 2 REAR PANEL TABLE 3 DESCRIPTIONS OF THE PORTS AND BUTTONS Identification Description POWER Connected to the companion power adapter. On/Off Power switch Wi-Fi WLAN switch Reset When W300 is in operating status, pressing this button for more than 5 seconds will restore the device default settings and then the device will reboot automatically.
Chapter 2 Product Installation Hardware Connections Follow the steps below to perform hardware connections. 1. Place the W300 router on the plane surface. Minimize obstacles and the distance between the W300 router and the wireless terminal. 2. Perform ADSL uplink connection A W300 router can access the ISP’s network in ADSL uplink mode, as shown in Figure 3.
ZXV10 W300 Wireless ADSL Router User Manual If a telephone needs to be installed before the splitter, the user must connect a voice filter in the Line port of the splitter; then connect the telephone after the voice filter. The other port connections can be referred to Figure 3. A splitter consists of three ports: ¾ Line: The port connected to the ADSL subscriber line. ¾ Modem: The port connected to DSL port of W300. ¾ Phone: The port connected to a telephone. 3.
Chapter 2 - Product Installation Note: If the W300 router fails to work due to error configuration or if the user forgets the login password, press the Reset button for more than 5 seconds to restore the settings to the default, then the system restarts automatically. Computer Configuration Checking Computer Configuration If the computer uses a proxy server to access the Internet, it is suggested to disable this proxy service before performing the configurations.
ZXV10 W300 Wireless ADSL Router User Manual 1. In Windows taskbar, click Start > Control Panel. 2. Double-click the Network Connection icon. 3. Right-click Local Area Connection and choose Properties from the pop-up short-cut menu. 4. Select Internet Protocol Properties button. (TCP/IP), and then click the 5. In the Internet Protocol (TCP/IP) Properties dialog box, check Obtain an IP address automatically and check Obtain DNS server address automatically. 6. Click OK to confirm and save the settings.
Chapter 3 Configuration Preparation Logging into Web Configuration Page Follow the procedure below to log into the Web configuration page. 1. Open a browser (e.g, IE) and type http://192.168.1.1 (i.e., default IP address of the W300’s LAN port) in the address bar. 2. Press the Enter key of the keyboard to display the login page. 3. Input the user name and password (marked on the label of W300 cover), and then click the Login button to open the main page for configuration.
Chapter 4 Network Configuration Creating WAN Connection Follow the steps below to create a WAN Connection. 1. Click Network > WAN Connection to open the WAN configuration page, as shown in Figure 4. FIGURE 4 THE WAN CONFIGURATION P AG E 2. From the Connection Name pull-down list box, choose Create WAN Connection to create a new WAN connection or choose an existing WAN connection, as shown in Figure 5.
Chapter 4 - Network Configuration FIGURE 5 CREATING A WAN CONNECTION – 1 3. Choose a connection type from the Type pull-down list box, as shown in Figure 6. FIGURE 6 CREATING A WAN CONNECTION – 2 4. Configure parameters according to the specified network type. If PPPoE is selected, the WAN connection configuration page is shown as Figure 7. To create a PPPoE WAN connection, perform the following operations. i. Specify the New Connection Name. ii. Specify the VPI/VCI value (provided by ISP).
ZXV10 W300 Wireless ADSL Router User Manual If PPPoA is selected, the WAN connection configuration page is shown as Figure 7. To create a PPPoA WAN connection, perform the following operations. i. Specify the New Connection Name. ii. Specify the VPI/VCI value (provided by ISP). iii. Input the Username and Password (provided by ISP). iv. Leave the other parameters as default. v. Click the Create button.
Chapter 4 - Network Configuration FIGURE 9 CREATING A WAN CONNECTION – 5 If DHCP selected, the WAN connection configuration page is shown as Figure 10. To create a DHCP WAN connection, perform the following operations. i. Specify the New Connection Name. ii. Specify the VPI/VCI value (provided by ISP). iii. Leave the other parameters as default. iv. Click the Create button.
ZXV10 W300 Wireless ADSL Router User Manual If Bridge Connection selected, the WAN connection configuration page is shown as Figure 11. To create a bridge mode WAN connection, perform the following operations. i. Specify the New Connection Name. ii. Specify the VPI/VCI value (provided by ISP). iii. Leave the other parameters as default. iv. Click the Create button.
Chapter 4 - Network Configuration Channel: To select the channel for communication between the W300 router and the wireless terminal devices. It is recommended to use channel 1, 6 and 11. It is recommended to leave other parameters as default. If it is necessary to professionals. change the parameters, please consult the Click the Submit button to complete the basic configuration.
ZXV10 W300 Wireless ADSL Router User Manual FIGURE 13 THE WLAN SECURITY CONFIGURATION PAGE 2. Select an encryption type from the Authentication Type pulldown list box, as shown in Figure 14.
Chapter 4 - Network Configuration ¾ WEP Key1 ~ WEP Key4: To input the encryption key. For a 128-bit key, input 26 hexadecimal digits or 13 ASCII characters; for a 64-bit key, input 10 hexadecimal digits or 5 ASCII characters. Click Submit to complete the configuration of WEP encryption. FIGURE 15 SETTING WLAN SECURITY PARAMETERS – 2 Note: WEP (Wired Equivalent Privacy) encryption is a popular adopted WLAN security protocol to enhance the security and confidentiality of wireless communication.
ZXV10 W300 Wireless ADSL Router User Manual FIGURE 16 SETTING WLAN SECURITY PARAMETERS – 3 Note: WPA encryption is Wi-Fi encryption (Wi-Fi Protected Access). Configuring Multiple SSIDs SSID is the name of a wireless access point to be distinguished from another. It is case sensitive and must not exceed 32 characters. Users can set multiple SSIDs for W300. Click Network > WLAN > Multi-SSID Settings to open the SSID configuration page, as shown in Figure 17.
Chapter 4 - Network Configuration ¾ Hide SSID: If this option is enabled, this SSID will not be searched by the wireless terminal devices. ¾ Enable SSID: Choose this option to enable this SSID. ¾ SSID Name: Input an SSID name (1~32 characters). ¾ Priority: Set a priority level: 0~7 Click Submit to complete the configuration of multiple-SSID settings. Checking Associated Device Follow the steps below: 1.
Chapter 5 Application Configuration Configuring UPnP Follow the steps below: 1. Click Application > UPnP to open the UPnP configuration page. 2. Enable the UPnP function and specify the WAN connection type. 3. Click Submit to save the configurations. Configuring DMZ Host It is required to enable the DMZ host function in the case that W300 is operating in routing mode and a local host needs to be accessed by the external network. Follow the steps below: 1. Click Application > configuration page.
Chapter 6 Troubleshooting This chapter describes how to troubleshoot problems when installing and using a W300. For any problems not addressed here; contact the service provider for help. TABLE 4 TROUBLESHOOTING Problem The power indicator is OFF when the device is powered on. The DSL indicator is OFF when the telephone line is connected. When the telephone line is connected, the DSL indicator is in slowly flashing status. The LAN indicator is OFF when the Ethernet cable is connected.
Appendix A WLAN Configuration To access the W300 router in the wireless way, users need to configure WLAN settings for computer. The following example assumes that a laptop computer with a built-in wireless network adatper is used and the operating system is Windows XP. Follow the steps below to configure WLAN on computer: 1. From the Windows taskbar, click Start > Control Panel. 2. Double-click the Network Connections icon to open the Network Connections window. 3.
Appendix A - WLAN Configuration FIGURE 18 WIRELESS NETWORKS 6. Check if the desired WLAN SSID is included in the Preferred networks area. If yes, select it. If no, click the Add button to open the configuration page shown in Figure 19.
ZXV10 W300 Wireless ADSL Router User Manual 7. In the Network name (SSID) field, input an SSID (the same as the one set for the W300 router, case sensitive). If the W300 router enables wireless security, supposing that the user adopts WEP 64-bit as Authentication Type and Ee68o as Encryption key, select Open for Network Authentication and WEP for Data encryption. Uncheck The key is provided for me automatically. In the Network key fields, input Ee68o, and then click OK to return. 8.
Appendix A - WLAN Configuration FIGURE 21 CHOOSING WIRELESS NETWORK FIGURE 22 SUCCESSFUL WIRELESS CONNECTION Confidential and Proprietary Information of ZTE CORPORATION 25