ZXV10 W812N V2 Indoor Wireless Access Point User Manual ZTE CORPORATION NO. 55, Hi-tech Road South, ShenZhen, P.R.China Postcode: 518057 Tel: +86-755-26771900 Fax: +86-755-26770801 URL: http://ensupport.zte.com.cn E-mail: support@zte.com.
LEGAL INFORMATION Copyright © 2012 ZTE CORPORATION. The contents of this document are protected by copyright laws and international treaties. Any reproduction or distribution of this document or any portion of this document, in any form by any means, without the prior written consent of ZTE CORPORATION is prohibited. Additionally, the contents of this document are protected by contractual confidentiality obligations.
Contents Chapter 1 Safety Precautions.................................................................... 1-1 Chapter 2 Product Introduction ................................................................ 2-1 2.1 Product Introduction ........................................................................................... 2-1 2.2 Typical Application.............................................................................................. 2-1 2.3 Indicators Status Description..........................
6.2.7 Scanning an Access Point ...................................................................... 6-18 6.2.8 Configuring WDS ................................................................................... 6-19 6.2.9 Configuring STA WMM ........................................................................... 6-20 6.2.10 Configuring AP WMM ........................................................................... 6-21 6.2.11 Setting Channel Auto-Switch .............................................
9.2.1 Managing SNMPv3 Users......................................................................... 9-2 9.2.2 Managing SNMPv1/v2c Users................................................................... 9-3 9.3 SNMPv3 Access Control Management (VACM).................................................... 9-3 9.3.1 Managing Context .................................................................................... 9-3 9.3.2 Managing Security Groups..............................................................
IV SJ-20121126100147-001|2012-11-26(R1.
Chapter 1 Safety Precautions Installation l l l l l l Use the power adapter provided. If you use other power adapters, the device may be damaged or fails to operate properly. Make sure that the electric load of a power socket or a power cable meets the requirements. Overloading of power sockets or broken power cables may cause an electric shock or a fire. Check the cables periodically. Replace the damaged cables immediately.
ZXV10 W812N V2 User Manual This page intentionally left blank. 1-2 SJ-20121126100147-001|2012-11-26(R1.
Chapter 2 Product Introduction Table of Contents Product Introduction ...................................................................................................2-1 Typical Application......................................................................................................2-1 Indicators Status Description ......................................................................................2-2 Interface Description .......................................................................
ZXV10 W812N V2 User Manual Retailers, manufacturers and the working site needs to be changed frequently. l It is necessary to establish a LAN temporarily for a special project. The place that needs to establish a LAN temporarily such as commercial exhibitions, exhibition halls and construction sites; situations when the space needs to be expanded during the working peak hours such as retailers, airports and airlines; The condition when the financial approver needs to establish a client work group.
Chapter 2 Product Introduction 2.4 Interface Description The following table shows the description of various interfaces and buttons on the ZXV10 W812N V2. Name Description DC 12 V The power interface is to connect to the associated power adapter. WAN/PoE The Ethernet interface to connect the Network Interface Card (NIC) on a PC or other network devices through the RJ-45 network cable.
ZXV10 W812N V2 User Manual This page intentionally left blank. 2-4 SJ-20121126100147-001|2012-11-26(R1.
Chapter 3 Product Installation Table of Contents Installation Requirements ...........................................................................................3-1 Hardware Installation..................................................................................................3-1 Computer Configuration .............................................................................................3-2 3.
ZXV10 W812N V2 User Manual l The device can be powered directly through the switch supporting the standard PoE power supply, as shown in the following figure. The wall mounting installation description of ZXV10 W812N V2 in the actual environment is described as follows. 1. Place the positioning cardboard on the wall required to be mounted with a device. 2. Hammer nails on the round holes of the positioning cardboard (It is recommend to use expansion screws in the accessories). 3.
Chapter 3 Product Installation 2. In the Internet Options window, click the Connections tab and then click LAN Settings. 3. In the pop-up window, clear Use a proxy server for your LAN check box and then click OK. – End of Steps – 3.3.2 Setting TCP/IP Context This section takes the Windows XP operating system as an example to introduce TCP/IP configuration. Steps 1. In Windows task bar, select Start > Control Panel. 2. In Control Panel, double-click Network Connections. 3.
ZXV10 W812N V2 User Manual This page intentionally left blank. 3-4 SJ-20121126100147-001|2012-11-26(R1.
Chapter 4 Configuration Preparation Table of Contents Default Settings..........................................................................................................4-1 Requirements Before Configuration............................................................................4-1 Logging in to the System ............................................................................................4-2 4.1 Default Settings The default settings of the ZXV10 W812N V2 are described as follows.
ZXV10 W812N V2 User Manual l Ask the service provider for necessary configuration data. Consult the service provider for the specific information. 4.3 Logging in to the System Context The ZXV10 W812N V2 provides the configuration function based on a WEB page. Perform the configuration and management for the ZXV10 W812N V2 through the WEB browser. The default language of ZXV10 W812N V2 Web pages is English. Steps 1. Open Internet Explorer, and type http://192.168.0.
Chapter 4 Configuration Preparation l l Click to view the related help information on the current page. Click the Help tab to open the Help page to view the related help information. – End of Steps – 4-3 SJ-20121126100147-001|2012-11-26(R1.
ZXV10 W812N V2 User Manual This page intentionally left blank. 4-4 SJ-20121126100147-001|2012-11-26(R1.
Chapter 5 Device Status Table of Contents Checking Device Information......................................................................................5-1 Checking Information of Network Interfaces ...............................................................5-1 Checking WLAN Interface Information........................................................................5-3 5.1 Checking Device Information Steps 1. Click the Status tab and then select Device Information in the left pane.
ZXV10 W812N V2 User Manual 2. On the Ethernet page, check the Ethernet interface information such as Ethernet Port, MAC Address, Status, Mode, and Packets Sent/Bytes Sent. Note: Click Refresh on this page to refresh the related information of the current device. – End of Steps – 5.2.2 Checking Network Connection Information Steps 1. Click the Status tab and then select Network Interface > WAN Connection. The WAN Connection page is displayed. 2.
Chapter 5 Device Status Note: Click Refresh on this page to refresh the related information of the current device. – End of Steps – 5.3 Checking WLAN Interface Information Steps 1. Click the Status tab and then select User Interface > WLAN. The WLAN page is displayed. 2.
ZXV10 W812N V2 User Manual Note: Click Refresh on this page to refresh the related information of the current device. – End of Steps – 5-4 SJ-20121126100147-001|2012-11-26(R1.
Chapter 6 Network Configuration Table of Contents Broadband Connection Configuration .........................................................................6-1 WLAN Configuration...................................................................................................6-4 LAN Management ....................................................................................................6-24 Routing Management .........................................................................................
ZXV10 W812N V2 User Manual 2. Configure the parameters according to the parameter description in the table below. Parameter IP Version AC Discovery Mode Description Supported protocol versions include IPv4, IPv6 and IPv4/v6. The default setting is IPv4. Include DHCP, Static, DNS and Broadcast. The default setting is DHCP. AP Type Adapter AC Name Configurable when AC Discovery Mode is DNS. Enable CAPWAP Encryption Enable/Disable CAPWAP encryption.
Chapter 6 Network Configuration Parameter Description Specify the processing priority. It only applies to multiple 802.1p WAN connections, the range is 0 to 7. The default value is 0, which means no priority. A bigger value indicates a higher priority. Enable DSCP DSCP MTU Enable/Disable the Differential Services Code Point (DSCP) function of data flow. Specify the DSCP value. The value range is 0 to 63. Specify the Maximum Transmission Unit (MTU) value. The default value is 1448.
ZXV10 W812N V2 User Manual 2. Configure the parameters. For detailed information, refer to Configuring Broadband Connection (Fit AP). l Working mode: supports bridge mode and route mode. By default, it is the bridge mode. l WAN mode: When IP Version is IPv4, DHCP, Static and PPPoE are all supported while when IP Version is IPv6 or IPv4/v6, DHCP and PPPoE are supported. By default, it is DHCP. 3. Click Submit . Note: The configuration modification on this page only takes effect after the device restarts.
Chapter 6 Network Configuration Steps 1. Select Network > WLAN > Basic. The following page is displayed. 2. Configure the parameters. l When Network Card1 is selected, the WEB page is as shown above. Refer to the parameter descriptions in the table below to configure parameters. Parameter Description Network Card Use Network Card1. Enable Wireless RF Enable/Disable the WLAN RF function. Enable Isolation Enable/Disable the SSID isolation function. It is disabled by default.
ZXV10 W812N V2 User Manual Parameter Band Description If Network Card is Network Card1, the frequency band is 2.4 G. MIMO The options are 1*1, 1*2, 2*1 and 2*2. The default is 2*2. 11N Rate Specify the wireless transmission rate. The default is Auto. Specify a channel according to the country code. The available options are Auto or 1–13. The default channel is set as Auto.
Chapter 6 Network Configuration l Parameter Description Protection Mode Support None, CTS Only, and RTS/CTS. 5G Access First Enable/Disable the 5G access first function. When Network Card2 is selected, the WEB page is as shown in the following figure. Configure the parameters. Refer to the following table. Parameter Description Network Card Uses Network Card2. Enable Wireless RF Enables or disables the WLAN RF function. Enable Isolation Enables or disables the SSID isolation function.
ZXV10 W812N V2 User Manual Parameter Description Band If Network Card is Network Card2, the frequency band is 5 G. Band Width The available options are 20 MHz, 40 MHz and automatic. The default is 20 MHz. MIMO The options are 1*1, 1*2, 2*1 and 2*2. The default is 2*2. 11N Rate Specifies the transmission rate of 802.11n. There are 17 rates and the default value is auto. Channel Proper channel can be selected according to country code. The available options are Auto, 149, 153, 157, 161 or 165.
Chapter 6 Network Configuration Parameter Description Protection Mode Supports None, CTS Only, and RTS/CTS. 5G Access First Enables or disables the 5G access first function. 3. Click Submit. – End of Steps – 6.2.2 Configuring SSID Steps 1. Select Network > WLAN > SSID Settings . The following page is displayed. 2. Configure the parameters. Refer to the following table. Parameter Description Choose SSID Select the SSID required to be configured. The available options are from SSID1 to SSID32.
ZXV10 W812N V2 User Manual Parameter Description Isolation Mode Select the corresponding isolation mode. The available options are Unicast, Broadcast, Multicast and ALL. The default option is ALL. Maximum Clients Set the maximum number of users that are allowed to connect to the SSID. The default value is 32. The range is from 1 to 512. SSID Name Set a name for this SSID. A name is composed of 1–32 characters. Priority Set the SSID priority ranging from 0 to 7.
Chapter 6 Network Configuration 2. Configure the parameters according to the parameter description in the table below. Parameter Choose SSID Description Specifies the SSID to be configured. The range is SSID1 to SSID15. Supports Open System, Shared Key, Open System & Authentication Type Shared Key, WPA-PSK, WPA2-PSK, WPA/WPA2-PSK, WPA-EAP, WPA2-EAP, WPA/WPA2-EAP, WAPI-PSK, WAPI-CERT and WEP-EAP.
ZXV10 W812N V2 User Manual ii. Configure the parameters. Refer to the following table. Parameter Description Server Type Specifies the server type. The options are Master Auth Server, Master Acct Server, Backup Auth Server, and Backup Acct Server. The default is Master Auth Server. Server IP Address Specifies the IP address of the authentication server, for example 192.168.1.1. Server Port Specifies the port of the authentication server, for example, 1812. The range is 0 to 65535.
Chapter 6 Network Configuration i. Select Shared Key or Open System & Shared Key for Authentication Type. The following page is displayed. ii. Configure the parameters according to the parameter description in the table below. Parameter Description Enables or disables the WEP encryption function. The WEP Encryption default is enabled. There are two types of WEP key, namely 64 bit and WEP Encryption Level 128 bit. WEP Key Index Specifies corresponding key value. Specifies WEP encryption key value.
ZXV10 W812N V2 User Manual Parameter Description Supports two modes, namely ASCII and HEX. The WAPI Key Mode default is ASCII. Specifies WAPI key value. The length is 8 to 64 WAPI Key l characters. WAPI-CERT encryption i. Select WAPI-CERT as the Authentication Type. The following page is displayed. ii. Fill in Certificate Server IP and Certificate Server Port. iii. Click the Certificate Uploading button, and then select the proper type of certificate file in the dialog box that appears.
Chapter 6 Network Configuration ii. Configure the parameters according to the parameter description in the table below. Parameter Description Specify the server type. The options are Master Auth Server Type Server, Master Acct Server, Backup Auth Server and Backup Acct Server. The default is Master Auth Server. Server IP Address Server Port Secret Reauth Period Enable Preauth WEP Encryption Specify the IP address of the authentication server, for example 192.168.1.1.
ZXV10 W812N V2 User Manual 6.2.4 Setting Rate Limits Context Note: The value of the rate limit is 0, which represents there is no rate limit. Steps 1. Select Network > WLAN > Rate Limit from the menu bar. The following page is displayed. 2. Configure the parameters according to the parameter description in the table below. Parameter Description Control Type Support SSID/STA and MAC. Choose SSID Specify the SSID to be configured. The range is SSID1 to SSID16.
Chapter 6 Network Configuration Parameter Description STA Uplink Rate Limit The available range is from 0 kbps to 100000 kbps. It is 0 by default, which represents there is no rate limit. 3. Click Submit to submit the current configuration. – End of Steps – 6.2.5 Setting an Access Control List Steps 1. Select Network > WLAN > Access Control List from the menu bar to open the Access Control List page as shown below. 2. Configure the parameters according to the parameter description in the table below.
ZXV10 W812N V2 User Manual 6.2.6 Checking Associated Devices Steps 1. Select Network > WLAN > Associated Devices from the menu bar to open the Associated Devices page as shown below. 2. In Choose SSID, select the SSID interface required to be viewed. The user can view the detailed information of the associated device corresponding to the SSID interface. By default, the system displays the device information associating with SSID1 interface.
Chapter 6 Network Configuration Caution! When the SSID is disabled or the WIDS mode is Access, this page cannot be configured. 3. Click Scan and then the corresponding scan result will be displayed on the refreshed page. – End of Steps – 6.2.8 Configuring WDS Steps 1. Select Network > WLAN > WDS from the menu bar to open the WDS page as shown below. 2. Select the NIC required to be configured and then configure the parameters according to the WDS mode.
ZXV10 W812N V2 User Manual l When WDS Mode is WDS+Repeater, the configuration page is as shown below. Configure the parameters according to the parameter description in the table below. Parameter Description Display the MAC address information of the WDS WDS Interface MAC Address interface. Root MAC Address Set the MAC address of the root AP. 3. Click Submit to submit the current configuration. – End of Steps – 6.2.9 Configuring STA WMM Steps 1.
Chapter 6 Network Configuration Parameter Description Choose AC The available options are VO, VI, BE or BK. AIFSN The available range is 2-15. ECWMin The available range is 0-15. ECWMax The available range is 0-15. TXOP The available range is 0-255. Qlength The available range is 0-1000. SRL The available range is 0-255. LRL The available range is 0-255. 3. Click Submit to submit the current configuration. – End of Steps – 6.2.10 Configuring AP WMM Steps 1.
ZXV10 W812N V2 User Manual Parameter Description Qlength The available range is 0-1000. SRL The available range is 0-255. LRL The available range is 0-255. 3. Click Submit to submit the current configuration. – End of Steps – 6.2.11 Setting Channel Auto-Switch Steps 1. SelectNetwork > WLAN > Channel Auto-Switchfrom the menu bar. The following page is displayed. 2. Configure the parameters according to the parameter description in the table below.
Chapter 6 Network Configuration 6.2.12 Setting Wireless Mode Steps 1. Select Network > WLAN > Wireless Mode from the menu bar. The following page is displayed. 2. Select the network card to be configured. Coverage or Only Backhaul. Specify Wireless Mode to be Only 3. Click Submit to submit the current configuration. – End of Steps – 6.2.13 Setting Mesh Configuration Steps 1. Select Network > WLAN > Mesh Configuration from the menu bar. The following page is displayed. 2.
ZXV10 W812N V2 User Manual 6.3 LAN Management 6.3.1 Managing Addresses Context The DHCP start IP address and the DHCP end IP address should be inside the subnet of LAN IP. Steps 1. Select Network > LAN > Address Management from the menu bar to open the Address Management page as shown below. 2. Configure the parameters according to the parameter description in the table below. Parameter LAN IP Address Description IP address of LAN group (interface subnet). The default IP address is 192.168.1.1.
Chapter 6 Network Configuration Parameter Description l When the access point mode of the device is fit, the supported status includes DHCP Server and OFF. It is DHCP Service DHCP Server by default. l When the access point mode of the device is fat, the supported status includes DHCP Server, DHCP Relay and OFF. It is DHCP Server by default. The start IP address allocated by the DHCP Server.
ZXV10 W812N V2 User Manual 2. Type Start IP Address and End IP Address, Click Modify. – End of Steps – 6.3.3 Managing an IPv6 Address Steps 1. Select Network > LAN > IPv6 Address Management from the menu bar to open the IPv6 Address Management page as shown below. 2. On this page, you can re-configure the IPv6 address of this terminal. 3. Click Submit to submit the current configuration. – End of Steps – 6.4 Routing Management (IPV4) ) 6.4.1 Configuring a Static Route( Steps 1.
Chapter 6 Network Configuration 2. Configure the parameters according to the descriptions in the table below. Parameter Description WAN Connection Select the corresponding interface as required. Network Address Network address of the destination network Subnet Mask Subnet mask of the destination network Gateway IP address of the gateway (next hop) Modify Click to edit the corresponding static route rule. Delete Click to delete the corresponding static route rule. 3.
ZXV10 W812N V2 User Manual Parameter Description prefix Type IPV6 address in the former space, and type subnetwork prefix length in the later space Gateway Gateway (next hop) IP address Modify Click to edit the corresponding static route rule. Delete Click to delete the corresponding static route rule. 3. Click Add to submit the current configuration. – End of Steps – 6.4.3 Setting a Dynamic Route Context This section describes how to set a dynamic route. Steps 1.
Chapter 7 Security Configuration Table of Contents Configuring a Firewall.................................................................................................7-1 Configuring IP Filter....................................................................................................7-2 Configuring MAC Filter ...............................................................................................7-4 Viewing a Service List ...................................................................
ZXV10 W812N V2 User Manual Parameter Description Select high, middle, low or off as required. Firewall level description l High: Allow legal WAN side access, but prohibit PING from the WAN side. Firewall Level l Middle: Allow legal WAN side access and resist certain types of dangerous data traveling over Internet. l Low: Allow legal WAN side access and PING from the WAN side. l Off: This option is not recommended.
Chapter 7 Security Configuration 2. Configure the parameters according to the parameter description in the table below. Parameter Description Enable Enable/Disable the IP filter function. Protocol Specify a protocol (including ANY, TCP, UDP, TCP AND UDP and ICMP. Where, ANY refers to any protocol). Name IP filter name. The length is 1 to 256 characters. Start Source IP Address The start source (LAN side) IP address. End Source IP Address The end source (LAN side) IP address.
ZXV10 W812N V2 User Manual Parameter Description Modify Click to modify the corresponding IP filter rule. Delete Click to delete the corresponding IP filter rule. 3. Click Add to submit the current configuration. – End of Steps – 7.3 Configuring MAC Filter Context Note: In the Permit mode, please type the local MAC address, otherwise the network cannot be accessed. Steps 1. Select Security > MAC Filter from the menu bar to open the MAC Filter page as shown below. 2.
Chapter 7 Security Configuration Parameter Description Source MAC Address The device MAC address on the LAN side Destination MAC Address The device MAC address on the WAN side Modify Click to modify the corresponding MAC filter rule. Delete Click to delete the corresponding MAC filter rule. 3. Click Submit to submit the current configuration. – End of Steps – 7.4 Viewing a Service List Steps 1. Select Security > Service List from the menu bar to open the Service List page as shown below. 2.
ZXV10 W812N V2 User Manual 2. Select the corresponding ALG switches to be enabled as required. 3. Click Submit to submit the current configuration. – End of Steps – 7-6 SJ-20121126100147-001|2012-11-26(R1.
Chapter 8 Application Configuration Table of Contents Configuring UPnP ......................................................................................................8-1 Setting a Device Name...............................................................................................8-2 QoS Configuration......................................................................................................8-3 Configuring SNTP ..........................................................................
ZXV10 W812N V2 User Manual Parameter Description Enable Enable/Disable the UPnP function. It is disabled by default. WAN Connection Select the corresponding WAN connection as required. Advertisement Period (in minutes) Set the corresponding time as required. Unit: minute. Advertisement Time To Live (in Set the corresponding time to live (hop count) as required, hops) for example 4. 3. Click Submit to submit the current configuration. – End of Steps – 8.
Chapter 8 Application Configuration Note: The items with the dimmed button are allocated from a DHCP server, which are inoperable. l Click to edit the corresponding host information. l Click to delete the corresponding host information. – End of Steps – 8.3 QoS Configuration Quality of Service (QoS) defines the quality agreement on the information transmission and sharing between network users.
ZXV10 W812N V2 User Manual Parameter Enable Queue Management Description Enable/Disable the function of congestion management. It is disabled by default. The available algorithms are SP, DWRR and SP_DWRR. SP: Send the group in a queue with higher priority in descending Scheduler Algorithm order of priorities. When the queue with higher priority is empty, the device will send the group in a queue with lower priority. DWRR: the priority cycle by weighting. Each queue is served by turn.
Chapter 8 Application Configuration 2. Configure the parameters according to the parameter description in the table below. Parameter Description Enable Enable/Disable the function of QoS classification configuration. The entrance of packets. Select a LAN interface or the SSID DevIn having been configured. You can only select one interface at a time. L2Protocol L3Protocol Source MAC Address Select the layer-2 protocol for packets including IPV4, IPv6, ARP and PPPoE.
ZXV10 W812N V2 User Manual Parameter Description Destination IPv6 Address Fill in the minimum value and maximum value of packet MIN/MAX destination IPv6 address. Traffic Class Traffic type ranging from 0 to 255. Flow Label Set the flow flag ranging from 0 to 1048575. 3. Click Add to submit the current configuration. – End of Steps – 8.3.3 Configuring Congestion Management Context The default congestion management algorithm is SP. The default queue is Queue 8. It is enabled by default. Steps 1.
Chapter 8 Application Configuration 4. Click Modify to submit the current configuration. – End of Steps – 8.4 Configuring SNTP Context Configure the related information of SNTP on the device to realize the time synchronization with the time server. Steps 1. Select Application > SNTP from the menu bar to open the SNTP page as shown below. 2. Configure the parameters according to the parameter description in the table below.
ZXV10 W812N V2 User Manual 8.5 IGMP Configuration The multicast function supports sending the same data to several devices. The IP host uses an Internet Group Management Protocol (IGMP) to report the qualifications of multicast group members to the neighboring router by sending data. At the same time, the multicast router uses the IGMP to find which hosts belong to the same multicast group. The device supports processing IGMP packets through the IGMP proxy.
Chapter 8 Application Configuration 2. Configure the parameters according to the parameter description in the table below. Parameter Description Enable IGMP Proxy Enable/Disable the IGMP function. Enable IGMP Snooping Enable/Disable the IGMP listening function. Enable IGMP Snooping Enhancement Enable/Disable IGMP Snooping Enhancement function. 3. Click Submit to submit the current configuration. – End of Steps – 8.6 Configuring MLD Listening Steps 1.
ZXV10 W812N V2 User Manual 3. Click Submit to submit the current configuration. – End of Steps – 8-10 SJ-20121126100147-001|2012-11-26(R1.
Chapter 9 Management Configuration Table of Contents Managing SNMPv1/v2c ..............................................................................................9-1 SNMPv3 Security Management (USM).......................................................................9-2 SNMPv3 Access Control Management (VACM)..........................................................9-3 User Management......................................................................................................
ZXV10 W812N V2 User Manual 3. Click Submit to submit the current configuration. – End of Steps – 9.2 SNMPv3 Security Management (USM) 9.2.1 Managing SNMPv3 Users Steps 1. Select Administration > SNMPv3 Security (USM) > SNMPv3 Users. The following page is displayed. 2. Configure the parameters. Refer to the following table.
Chapter 9 Management Configuration 9.2.2 Managing SNMPv1/v2c Users Steps 1. Select Administration > SNMPv3 Security(USM) > SNMPv1/v2c Users. following page is displayed. The 2. Configure the parameters. Refer to the following table. Parameter Description Security Name User Name Source IP IP address of the source Modify Click to modify the corresponding SNMPv1/v2c user information Delete Click to delete the corresponding SNMPv1/v2c user information 3. Click Add. – End of Steps – 9.
ZXV10 W812N V2 User Manual 9.3.2 Managing Security Groups Steps 1. Select Administration > SNMPv3 Access Control (VACM) > Security To Group. The following page is displayed. 2. Configure the parameters. Refer to the following table. Parameter Description Security Model Support USM, SNMPv1, and SNMPv2c. Security Name Specify the security user name. Group Name Specify the group name. Modify Click to modify the corresponding security group information.
Chapter 9 Management Configuration 2. Configure the parameters. Refer to the following table. Parameter Description View Name View name. Subtree Subtree name. Mask (Optional) Subnet mask. Type The options are included and excluded. Modify Click to modify the corresponding view information. Delete Click to delete the corresponding view information. 3. Click Add. – End of Steps – 9.3.4 Managing Access Table Steps 1. Select Administration > SNMPv3 Access Control (VACM) > Access Table.
ZXV10 W812N V2 User Manual 2. Configure the parameters. Refer to the following table. Parameter Description Group Name Group name. Context Prefix Information of the context prefix. Security Model Support USM, SNMPv1, SNMPv2c, and any. Security Level Support noAuthNoPriv, autoNoPriv, and authPriv. Context Match Support exact and prefix. Read View Name Support none and all. Write View Name Support none and all. Notify View Name Support none and all.
Chapter 9 Management Configuration 2. Configure the parameters. Refer to the following table. Parameter User Privilege Username Old Password New Password Confirm Password Description Determine whether to modify the management maintenance account or common account. The management maintenance account is admin and it cannot be modified. The common account is user and it can be modified. To modify the password of the management maintenance account, enter the original login password.
ZXV10 W812N V2 User Manual 9.5 Device Management 9.5.1 Setting System Management Steps 1. Select Administration > System Management > System Management. following page is displayed. The 2. The user can restart the device and restore default settings. l Click Reboot to restart the device. l Click Restore Default to restore the factory settings. – End of Steps – 9.5.
Chapter 9 Management Configuration 2. Click Browse to select the desired software version file. 3. Click Upgrade to upgrade the software version. – End of Steps – 9.5.3 Managing User Configuration Steps 1. Select Administration > System Management > User Configuration Management. The following page is displayed. 2. Choose backup operation or configuration import based on the actual requirement.
ZXV10 W812N V2 User Manual 2. Choose backup operation or configuration import based on the actual requirement. l Export the default configuration file Click Backup Configuration to back up the current configuration file of the device. l Import the default configuration file i. Click Browse and select the default configuration file to be imported. ii. Click Restore Configuration. Then, the specified default configuration file is imported.
Chapter 9 Management Configuration 2. Configure the parameters according to the descriptions in the table below. Parameter Enable Save Log Description Enable/Disable the function of log server management. It is disabled by default. Log levels are Debug, Informational, Notice, Warning, Error, Log Level Critical, Alert, and Emergency in the ascending priority order. After a log level is selected, only logs of the selected level and with higher levels will be recorded.
ZXV10 W812N V2 User Manual 2. Set AP mode, Fat or Fit, based on the actual requirement. The default AP mode is Fit. Note: After the AP mode is switched, the device restarts automatically. 3. Click Submit. – End of Steps – 9.7.2 Setting an Access Point Name Steps 1. Select Administration > AP Management > AP Name. displayed. The following page is 2. In AP Name field, set the corresponding name as required. 3. Click Submit to submit the current configuration. – End of Steps – 9.
Chapter 9 Management Configuration 2. Configure the parameters. Refer to the following table. Parameter Description IP Address or Host Name The host IP address or host name Ping num Specify the ping number Ping packet size Specify the size of the ping packet. The range is from 1 to 4096 Egress Select the egress to be diagnosed 3. Click Submit. The PING result is displayed in the text box in the lower part. – End of Steps – 9.8.2 Configuring Trace Route Diagnosis Steps 1.
ZXV10 W812N V2 User Manual 2. Configure the parameters. Refer to the following table. Parameter Description IP Address or Host Name The host IP address or host name. WAN Connection Select the WAN connection to be diagnosed. Maxinum Hops Select the maximum number of hops to be diagnosed. Wait Time Select the time-out period. 3. Click Submit. The Trace Route result is displayed in the text box in the lower part. – End of Steps – 9-14 SJ-20121126100147-001|2012-11-26(R1.
Appendix A Troubleshooting The solutions for the common problems during the installation and operation of the ZXV10 W812N V2 are provided in this section. For any unresolved problems, contact the service provider for help. Problem Solution A MAC address is the unique identifier of a network device. This problem can be resolved in the following two ways: How to know the MAC address of the device? l Check the MAC address of this device on the little label at the bottom of each device.
ZXV10 W812N V2 User Manual Problem Solution The bandwidth of a device is not high due to environment interference in most cases. However, sometimes, an ageing device may be causing the low transmission power. You can try the following methods to solve this problem: l Wireless channels. You can try to select other channels to check whether the rate can be improved dramatically. Why the bandwidth is not l Wireless interference.
Appendix B Technical Specifications Physical Specifications l l Size (Lengh× Width × Height): 7.075 inch (180 mm) × 6.486 inch (165 mm) × 1.789 inch (45.5 mm) Weight (excluding the power adapter): 1.764 lbs (800 g) Electric Standards l l Power adapter: Input 100 VAC to 240 VAC 50/60Hz; output 12 VDC/1500 mA POE power supply Power Consumption Power consumption of the equipment is less than 12.5 W.
ZXV10 W812N V2 User Manual This page intentionally left blank. B-2 SJ-20121126100147-001|2012-11-26(R1.
Appendix C Computer WLAN Configuration Context To access WLAN (Wi-Fi) from the user’s computer, it is required to configure WLAN settings of the computer. The following example assumes that a laptop computer with a built-in network interface card (NIC) is used and the operating system is Windows XP. Steps 1. In Windows taskbar, select Start > Control Panel. 2. Double-click Network Connection and right-click Wireless Network Connection. Then click Properties, as shown in the following figure. 3.
ZXV10 W812N V2 User Manual If there is no desired SSID, click the Add button. Then the Association page appears. 5. On the Association page, type an SSID (it should be the same as the one set in the terminal and is case sensitive) in the network name text box. Supposing that the terminal adopts WPA-PSK for Network Authentication and 12345678 for the Data encryption, perform the following procedure in the computer: Network Authentication is selected as WPA-PSK while Data encryption is selected as TKIP.
Appendix C Computer WLAN Configuration 6. Click View Wireless Networks to view the wireless network list in the figure above. Check the wireless network list to see if the newly added wireless network connection exists. If not, click Refresh network list on the left pane of the page. If the wireless network is found, select it and then click Connect, as shown below. 7. Type the encryption key again and click Connect. 8. After the wireless network is connected successfully, the following page appears.
ZXV10 W812N V2 User Manual – End of Steps – C-4 SJ-20121126100147-001|2012-11-26(R1.
Appendix D CE and FCC Compliance Statement ZXV10 W812N V2 is compliant with the requirements of CE and FCC. CE Compliance Statement Country CE Compliance Statement Bulgarian С настоящето, ZTE corporation декларира, че това безжично устройство е в Български съответствие със съществените изисквания и другите приложими разпоредби на Директива 1999/5/EC.
ZXV10 W812N V2 User Manual Country CE Compliance Statement German Hiermit erklärt ZTE corporation dass sich dieser/diese/dieses Radio LAN device Deutsch in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi) Hiermit erklärt ZTE corporation die Übereinstimmung des Gerätes Radio LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG.
Appendix D CE and FCC Compliance Statement Country CE Compliance Statement Turkish ZTE corporation bu kablosuz cihazın temel gereksinimleri ve 1999/5/EC Turk yonergesindeki ilgili koşulları karşıladığını beyan eder. FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
ZXV10 W812N V2 User Manual This page intentionally left blank. D-4 SJ-20121126100147-001|2012-11-26(R1.
Glossary CE - CONFORMITE EUROPENDE DHCP - Dynamic Host Configuration Protocol DNS - Domain Name Server FCC - Federal Communication Commission IP - Internet Protocol LAN - Local Area Network MAC - Medium Access Control NAT - Network Address Translation OFDM - Orthogonal Frequency Division Multiplexing PoE - Power over Ethernet WAN - Wide Area Network WLAN - Wireless Local Area Network I SJ-20121126100147-001|2012-11-26(R1.